Moon Down Series Surface Mounted Light
Product Information
The Moon Down Series (Surface Mounted) is a lighting fixture
designed for installation on the ceiling. It comes in various
sizes, including 11.8″ (300mm), 15.7″ (400mm), 18.9″ (450mm), 23.6″
(600mm), 35.4″ (900mm), and 47.2″ (1200mm) brackets.
Product Usage Instructions
- Shut OFF the electricity at the electrical panel. Place the
wall switch in the OFF position of the room you are installing the
fixture. - Use a screwdriver to relieve the canopy screw a little (Do NOT
REMOVE). Rotate the mounting bracket and remove it from the bottom
bracket. - Remove the plastic pin and drill 4 or 6 holes with a diameter
of 6mm on the ceiling according to the mounting bracket. Note that
if the fixture diameter is larger than 2ft, 6 holes are required (4
for bracket screws and 2 for safety bracket screws). Safety cable
suspension is only applicable for diameters of 3ft and above; for
diameters of 2ft and below, no safety cable suspension is
required. - Insert the expansion bolts into the holes. Use 2 pcs M4*25mm
screws to attach the mounting bracket to the J-Box. Refer to the
provided picture for reference. Note that the J-Box should be
Garvin 54171-S or equivalent, provided by others. - Use 4 or 6 pcs (2 for Safe Bracket) M4*25 self-tapping screws
to attach the mounting bracket on the ceiling. Connect the safety
cable between the mounting bracket and canopy. Ensure that the
mounting plate is secured at all connection points (junction box
plus four outer points for small and medium sizes, or six outer
points for larger sizes) to support the fixture weight
appropriately. Not using all mounting points could damage the
fixture and void the product warranty. - Use wire connectors to connect the L, N, G, DIM+, DIM- wires.
Then place all wires with connectors into the J-Box. - Keep the slot hole in a vertical line with the side screw.
Then, screw into the slot. Next, rotate the lamp body to complete
the installation. - After installation is complete, turn on the electricity at the
electrical panel.
Warnings
- Read the installation manual carefully before installation and
keep it for future reference. - Strictly follow the instructions listed in the manual to avoid
mis-operation or damage caused by not following the installation
manual. - Ensure that the mounting plate is secured at all connection
points to support the fixture weight appropriately. Not using all
mounting points could damage the fixture and void the product
warranty.
MOON DOWN SERIES (SURFACE MOUNTED)
INSTALLATION INSTRUCTIONS
Please read this installation manual carefully before installation. Keep it for future reference! Products are well packed and tested before leaving our factory. Please strictly follow the instructions listed in the manual. Factory cannot be held responsible for any mis-operation or damage caused by not following the installation manual!
Installation Diagram
Step 1 Shut “OFF” the electricity at electrical panel. Place the wall switch in the “OFF” position ofthe room you are installing the fixture.
Step2 Use Screw driver to relieve Canopy screw a little.(Do NOT REMOVE). Rotate Mounting Bracket and Remove it from Bottom Bracket as shown below.
luxlogiclighting.com | tel. 416-833-5515 toll free. 1-888-553-8003 | [email protected] Rev 1.0 27.11.2022
INSTALLATION INSTRUCTIONS
Step3 Remove Plastic Pin ,drill 4 pcs or 6 pcs diameter 6mm holes on the ceiling according to Mounting Bracket. (note: If the fixture dia is larger than 2″ , 6 holes are required, 4 for Bracket screw, 2 for safety Bracket screw). Please note: safety cable suspension is only applicable for diameters of 3ft and above. For
diameters of 2ft and below, no safety cable suspension is required.
Insertthe expansion bolts into the holes.( Use 2 pcs M4*25mm Screws to attach Mounting Bracketto the J-Box. Refer to picture shown below. NOTE:J-BOX Garvin 54171-S or equivalent / Provided by others
Step4
Use 4pcs or 6 pcs (2 for Safe Bracket) M4*25 Self-Tapping screw to attach Mounting Bracket on the ceiling. And Connect the safety cable between Mounting Bracket and Canopy.
luxlogiclighting.com | tel. 416-833-5515 toll free. 1-888-553-8003 | [email protected] Rev 1.0 27.11.2022
INSTALLATION INSTRUCTIONS
Attention: Must secure mounting plate at all connection points (junction box plus four outer points for small and medium sizes, or six outer points for larger size) to support fixture weight appropriately. Not using all mounting points could damage the fixture and void product warranty.
Step 5 Use wire connectors to connect L,N,G,DIM+,DIM- wires. Then place all wires with connectors into J-Box
Step 6 Keep the Slot hole in a vertical line with Side screw. Then, screw into slot. Next, rotate lamp body To complete installation.
luxlogiclighting.com | tel. 416-833-5515 toll free. 1-888-553-8003 | [email protected] Rev 1.0 27.11.2022
INSTALLATION INSTRUCTIONS
Step 7 After installation is complete, turn on the electricity at the electrical panel.
Warnings
MIN 90 °C SUPPLY CONDUCTORS/LES FILS D’ALIMENTATION 90 °C MIN DAMP LOCATIONS ONLY/POUR EMPLACEMENTS SECS SEULEMENT CAUTION RISK OF FIRE/ATTENTION RISQUE D’INCENDIE
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED/CE PRODUIT DOIT ÊTRE INSTALLÉ SELON LE CODE D’INSTALLATION PERTINENT, PAR UNE PERSONNE QUI CONNAÎT BIEN LE PRODUIT ET SON FONCTIONNEMENT AINSI QUE LES RISQUES INHÉRENTS Application temperature for ring light is -20 ° ~40 ° humidity is 0~95 . Otherwise there may be harm to the lifespan of the ring light. Please TURN OFF POWER before installation. This lamp must be installed and maintained by electrician or qualified personnel. Pay attention to fire prevention, electricity and shock resistance. Please do not cover the combustibles on the fixture. All screws and terminals should be tightened and tightly inserted. No loosening and improper connection are allowed. Attention should be paid to the polarity of components, power supply, driver and so on. Terminals should be tightened and tightly inserted. No loosening and improper
luxlogiclighting.com | tel. 416-833-5515 toll free. 1-888-553-8003 | [email protected] Rev 1.0 27.11.2022
BRACKET DIMENSIONS 11.8″ (300mm) / 15.7″ (400mm)
INSTALLATION INSTRUCTIONS
18.9″ (450mm) / 23.6″ (600mm)
luxlogiclighting.com | tel. 416-833-5515 toll free. 1-888-553-8003 | [email protected] Rev 1.0 27.11.2022
BRACKET DIMENSIONS 35.4″ (900mm)
INSTALLATION INSTRUCTIONS
47.2″ (1200mm)
luxlogiclighting.com | tel. 416-833-5515 toll free. 1-888-553-8003 | [email protected] Rev 1.0 27.11.2022
LED, Downlight, Track Lights, Linear Lights – LuxLogic Lighting Inc.
