ASW45K-LT-G3 Three Phase Solar Inverters
Product Information
The product in question is the
ASW45K-LT-G3/ASW50K-LT-G3/ASW60K-LT-G3 Android device. This quick
installation guide provides essential information for the
installation and usage of the product. Please note that this guide
does not replace the user manual, and the contents may be updated
or revised due to product development. The latest version of the
user manual can be found in PDF format at www.solplanet.net.
Safety
It is important to adhere to safety guidelines when using this
product. The ASW45K-LT-G3/ASW50K-LT-G3/ASW60K-LT-G3 Android device
has been designed and tested according to international safety
requirements. However, residual risks may still exist. To prevent
personal injury, property damage, and ensure the long-term
operation of the product, it is crucial to read and follow all
safety instructions provided.
Intended Use
The product should only be used in countries where it is
approved by AISWEI and the grid operator. The type label must be
permanently attached and in a legible condition. It is important to
note that this document does not replace any regional, state,
provincial, federal, or national laws, regulations, or standards
that apply to the installation, electrical safety, and use of the
product.
Important Safety Instructions
The following safety instructions must be observed:
- Danger to life due to high voltages of the PV array
- Danger to life due to electric shock when touching live system
components in case of a ground fault - Danger to life due to electric shock from destruction of the
measuring device due to overvoltage - Risk of burns due to high temperature
- Risk of injury due to weight of the product
Symbols on the Label
The product label includes the following symbols:
- Beware of a danger zone: Indicates the need for additional
grounding or equipotential bonding at the installation site - Beware of high voltage and operating current: Only skilled and
authorized electricians should work on the inverter - Beware of hot surfaces: The inverter may become hot during
operation, so avoid contact - WEEE designation: Dispose of the product according to
electronic waste disposal regulations at the installation site - CE marking: The product complies with the requirements of
applicable EU directives - Certification mark: The product has been tested and received
quality certification mark from TUV - RCM Mark: The product complies with the requirements of
applicable Australian standards - Capacitor discharge: Danger to life due to high voltages in the
inverter. Do not touch live parts for 25 minutes after
disconnection from power sources - Observe the documentation: It is important to refer to all
documentation supplied with the product
EU Declaration of Conformity
This section pertains to the EU Declaration of Conformity for
the ASW45K-LT-G3/ASW50K-LT-G3/ASW60K-LT-G3 Android device.
Product Usage Instructions
To ensure proper usage and safety when using the
ASW45K-LT-G3/ASW50K-LT-G3/ASW60K-LT-G3 Android device, please
follow these instructions:
- Read the user manual: Before using the product, thoroughly read
and understand the user manual provided in PDF format at
www.solplanet.net. - Adhere to safety guidelines: Always prioritize safety. Follow
all safety instructions mentioned in the user manual and quick
installation guide. - Use in approved countries: Ensure that the product is used only
in countries where it is approved by AISWEI and the grid
operator. - Properly attach the type label: The type label must be
permanently attached to the product and in a legible
condition. - Handle with care: Avoid touching live system components in case
of a ground fault to prevent electric shock. - Avoid high temperatures: The product may become hot during
operation. Take precautions to prevent burns. - Consider product weight: Due to its weight, be cautious when
handling the product to avoid injury. - Follow disposal regulations: When disposing of the product,
adhere to electronic waste disposal regulations applicable at the
installation site. - Refer to documentation: Make sure to refer to all documentation
supplied with the product for proper installation, commissioning,
configuration, and decommissioning.
Note: For any further assistance or information, please consult
the user manual or contact customer support.
Quick Installation Guide
ASW45K-LT-G3/ASW50K-LT-G3/ASW60K-LT-G3
Android
iiOoSs
1 GENERAL INFORMATION
This quick installation guide does not replace the description in the user manual. The contents of this guide may be updated or revised due to product development. The information in this guide is subject to change without notice. The latest version of this document and the manual for installation, commissioning, configuration and decommissioning are to be found in PDF format at www.solplanet.net.
2 SAFETY
2.1 Intended use
The product is a transformerless PV inverter which converts the direct current of the PV generator into grid-compatible three-phase alternating current and then feeds the three-phase alternating current into the public power grid. The product is intended for indoor and outdoor applications. The product must only be connected with PV modules of protection class II (in accordance with IEC 61730, application class A). Do not connect any sources of energy other than PV modules to the product. The product is not equipped with an integrated transformer and therefore has no galvanic isolation. The product must not be operated with PV modules which require functional grounding of either the positive or negative PV conductors. This can cause the product to be irreparablyy damaged. The product may be operated with PV modules with frames that require protective earthing. All components must remain within their permitted operating ranges and their installation requirements at all times. Use the product only in accordance with the information provided in the user manual and with the locally applicable standards and directives. Any other application may cause personal injury or damage to property.
1
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
The product must only be used in countries for which it is approved by AISWEI and the grid operator. The type label must be permanently attached to the product and must be in a legible condition. This document does not replace any regional, state, provincial, federal or national laws, regulations or standards that apply to the installation, electrical safety and use of the product.
2.2 Important safety instructions
The product has been designed and tested strictly according to the international safety requirements. As with all electrical or electronical devices, there are residual risks despite careful construction. To prevent personal injury and property damage and to ensure long-term operation of the product, read this section carefully and observe all safety information at all times.
DANGER
Danger to life due to high voltages of the PV array
When exposed to sunlight, the PV array generates dangerous DC voltage which is present in the DC conductors and the live components of the product. Touching the DC conductors or the live components can cause to lethal electric shocks. If you disconnect the DC connectors from the product under load, an electric arc may occur leading to electric shock and burns. · Do not touch non-insulated cable ends. · Do not touch the DC conductors. · Do not touch any live components of the product. · Do not open the product. · All work on the product must only be carried out by qualified personnel who have read and fully understood all safety information contained in this document and the user manual. · Disconnect the product from voltage and energy sources and ensure it cannot be reconnected before working on the product. · Wear suitable personal protective equipment for all work on the product.
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
2
DANGER
Danger to life due to electric shock when touching live system components in case of a ground fault
If a ground fault occurs, parts of the system may still be live. Touching live parts and cables may result in death or lethal injuries due to electric shock. · Disconnect the product from voltage and energy sources and ensure it cannot be reconnected before working on the device. · Only touch the insulation of the cables of the PV modules. · Do not touch any parts of the substructure or frame of the PV array. · Do not connect PV strings with ground faults to the product.
WARNING
Danger to life due to electric shock from destruction of the measuring device due to overvoltage
Overvoltage can damage a measuring device and result in voltage being present in the enclosure of the measuring device. Touching the live enclosure of the measuring device results in death or lethal injuries due to electric shock. · Only use measuring devices with the measurement span higher than the DC input voltage range equal to or higher than the voltage rating of the product.
CAUTION
Risk of burns due to high temperature.
Some parts of the enclosure can become hot during operation. · During operation, do not touch any parts other than the enclosure lid of the product.
CAUTION
Risk of injury due to weight of product .
Injuries may result if the product is lifted incorrectly or dropped while being transported or mounted. · Transport and lift the product carefully. Take the weight of the product into account. · Wear suitable personal protective equipment for all work on the product.
3
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
2.3 Symbols on the label
Beware of a danger zone This symbol indicates that the inverter must be additionally grounded if additional grounding or equipotential bonding is required at the installation site. Beware of high voltage and operating current The inverter operates at high voltage and current. Work on the inverter must only be carried out by skilled and authorized electricians.
Beware of hot surfaces The inverter may become hot during operation. Avoid contact during operation.
WEEE designation Do not dispose of the product together with the household waste but in accordance with the disposal regulations for electronic waste applicable at the installation site.
CE marking The product complies with the requirements of the applicable EU directives.
Certification mark The product has been tested by TUV and got the quality certification mark.
RCM Mark The product complies with the requirements of the applicable Australian standards.
Capacitor discharge Danger to life due to high voltages in the inverter. Do not touch live parts for 25 minu-
25mins
tes after disconnection from the power sources.
Observe the documentation Observe all documentation supplied with the product.
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
4
3 EU DECLARATION OF CONFORMITY
Within the scope of the EU directives · Radio Equipment Directive 2014/53/EU (L 153/62-106. May 22. 2014) (RED) · Restriction of the use of certain hazardous substances 2011/65/EU (L 174/88, June 8, 2011) and 2015/863/EU (L 137/10, March 31,2015) (RoHS) AISWEI Technology Co., Ltd. confirms here with that the products described in this document are in compliance with the fundamental requirements and other relevant provisions of the above mentioned directives. The entire EU Declaration of Conformity can be found at www.solplanet.net.
5
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
4 OVERVIEW
1
2
34 5
6
+ PV1/40A –
+ PV2/32A –
+ PV3/32A –
+ PV4/40A –
+ PV5/32A –
No.
1 2 3 4 5 6
Name
DC-switch LED DC connector inputs
WiFi stick port Additional grounding screw RS485 communication port AC terminal
5 SCOPE OF DELIVERY
Mounting-bracket×1
AC/COM cover×1 DCconnector×10 WiFistick×1
Inverter×1
Screw accessory ×1 AC insulation sheet×3 Document packagex1
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
6
6 MOUNTING ENVIRONMENT
×
×
×
75°
×
××
×
No touching by children
+60
-25
IP66 4K4H
100%
max.4000m
500mm
500mm
500mm
500mm
500mm
500mm
7
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
7 DIMENSIONS
670
270
Unitmm
473 386
640
8 MOUNTING
8.1 Mounting-bracket
1
2
592
550
4-10
4
1
2
3 5
4-12
90°
70mm
6
19mm 13 N·m
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
8
8.2 Wall-Mounted Installation 1
2
M5
M5
2.5N·m
2.5N·m
OK
1
2
90°
3
9 SECOND PROTECTIVE GROUNDING
1
3
E
L=E+(2~3)mm L
2
4
5
M5 2.5N·m
9
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
10 AC CONNECTION
1
3
4
2
28-42mm
5
8.5mm<<10.5mm
130mm
E
E
L1 L2 L3 N PE
6
7 2
M4 1.6N·m
8
9
M6
M8
3.5N·m
12N·m
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
10
10
M4 1.6N·m
11
OK
11 DC CONNECTION
TYPE 1 1
2.5-6mm2
12mm
5-8mm
2
2
click
3
1
×
4
5
OK
1 2
1 2
TYPE 2 1
2.5-6mm2
8-10mm
2
5-8mm
11
3
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
4 1
2
3
6
1 2
3 7
5
OK
12 COMMUNICATION SETUP
12.1 WiFi/LAN/4G stick connection
1
2
3
1 2
4
5
2
×
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
OK
12
12.2 RS485 cable connection
1
2
3-5.5mm
8mm 30~100mm
4/1
3
M4
1.6N·m
1
3 2
4/2
ABG ABG
OFF ON
5
4
13
6
M4 1.6N·m
5
AB G ABG
OFF ON
RS485
……
RS485
……
ON
OFF
ON
RS485
OK
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
13 CONTACT
Please contact our Service Department if you have any technical questions about our products. The following information is needed to provide necessary assistance: —-Inverter model —-Inverter serial number —-Photovoltaic module model —-Photovoltaic modules number and strings number connected to each MPPT —-Fault code —-Installation location —-Warranty card
EMEA Service email: [email protected] APAC Service email: [email protected] LATAM Service email: [email protected] Aiswei Greater China Service email: [email protected] Hotline: +86 400 801 9996 Taiwan Service email: [email protected] Hotline: +886 809089212 https://solplanet.net/contact-us
Scan QR code:
Scan QR code:
Android
iOS
QG0047_ASW45-60K-LT-G3_EN-540-300224-00_0223
14
AISWEI Technology CO., Ltd
Home Page | Solplanet make solar for everybody
Contact Us | Solplanet
