Ethan Allen 09-2013 Nat Farida Alabaster Floor Lamp Instruction Manual

09-2013 NAT Farida Alabaster Floor Lamp

Product Information

The Farida Floor Lamp is a stylish and functional lighting
fixture that adds a touch of elegance to any room. It features a
sleek design with a harp, saddle, shade, finial, socket, and plug
cap. The lamp requires a maximum 150W three-way Type A light bulb
(not included) for operation.

Product Usage Instructions

1. Use care when unpacking the lamp and make sure to locate all
   the parts before disposing of the packaging materials.
2. No tools are required for assembly.
3. Start the assembly process by inserting the harp (A) into the
   saddle (B).
4. Next, install the shade (C) onto the harp (A).
5. Screw the finial (D) onto the harp (A) to secure the shade in
   place.
6. Install a light bulb (maximum 150W three-way Type A) into the
   socket saddle (E).
7. Before changing the bulb, make sure to unplug the lamp and
   allow the bulb to cool down.
8. To use the lamp, remove the plug cap (F) from the plug.

Care and Cleaning

1. Wipe the lamp with a soft dry cloth for regular cleaning.
2. Avoid using cleaners, scouring pads, or any abrasive materials
   that may damage the lamp’s surface.

Troubleshooting

If you encounter any issues with the lamp, refer to the
following troubleshooting steps:

• Problem: Bulb does not light
• Possible Cause: Bulb is burnt out or
  damaged
• What to Do: Replace the bulb with a new
  one.

• Problem: Power to lamp is off
• Possible Cause: Confirm power is on
• What to Do: Check if the power is turned
  on.

• Problem: Lamp is not plugged in
• Possible Cause: Confirm lamp is plugged
  in
• What to Do: Make sure the lamp is properly
  plugged into a power outlet.

If the lamp still does not work after troubleshooting, please
contact your local Ethan Allen Design Center for further
assistance.

Farida Floor Lamp Assembly Instructions
09-2013 NAT

IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, AND PERSONAL INJURY: This lighting fixture is for indoor use only. This lamp is equipped with a polarized plug. One plug blade is wider than the other. DO NOT MODIFY the plug or power cord in any way. DO NOT EXCEED the recommended bulb wattage. Use only the type of bulb specified. Keep flammable materials away from bulb. DO NOT OPEN the product or alter the wiring in any manner. Extension cord: Follow precautions provided with power cord.
Use care when unpacking. Locate ALL PARTS INCLUDED before disposing of packaging materials.

ASSEMBLY, CARE, AND TROUBLESHOOTING No tools are required for assembly. Light bulb is not included. Parts Included (refer to figure):
A. Harp (styles may vary) B. Saddle C. Shade (may be packed in separate carton)
D. Finial
E. Socket (attached, no assembly required) F.Plug Cap Assembly Procedure (refer to figure):
1. Insert Harp (A) into Saddle (B). 2. Install Shade (C) onto Harp (A). 3. Screw Finial (D) onto Harp(A). 4. Install lightbulb (150W max, three-way, Type A) into Socket Saddle (E). 5. Remove Plug Cap (F) from plug. Care and Cleaning:
1. Wipe with a soft dry cloth.
2. AVOID cleaners, scouring pads, etc. 3. Before changing bulb, unplug lamp and
allow bulb to cool.

TROUBLESHOOTING:

Problem:

Possible Cause:

What to Do:

Bulb does not light

Bulb is burnt out or damaged

Replace bulb

Power to lamp is off

Confirm power is on

Lamp is not plugged in

Confirm lamp is plugged in

After troubleshooting, if the lighting fixture still does not work, contact your local Ethan Allen Design Center. SAVE THESE INSTRUCTIONS

Page 1 of 1

12/5/2022

©2018 Ethan Allen Global, Inc.

Instructions de montage du lampadaire Farida
09-2013B, 09-2013S CONSIGNES DE SÉCURITÉ IMPORTANTES

POUR RÉDUIRE LES RISQUE D’INCENDIE, D’ÉLECTROCUTION ET DE BLESSURES: Ce luminaire est pour usage intérieur seulement.Cette lampe est équipée d’une fiche polarisée. Une fiche des lames est plus large que l’autre.NE MODIFIEZ pas le cordon ou sa fiche alimentation en quelque sorte.NE PAS DÉPASSER la puissance de l’ampoule recommandée. Utilisez uniquement le type d’ampoule spécifié. Gardez les produits inflammables loin ampoule. NE PAS OUVRIR le produit ou modifier le câblage de toute manière. Rallonge : fourni avec cordon d’alimentation des précautions. Soyez prudent lors du déballage. TROUVER TOUTES LES PIÈCES INCLUSES AVANT DE VOUS DÉBARRASSER DE MATÉRIAUX D’EMBALLAGE.
ASSEMBLAGE, ENTRETIEN ET DÉPANNAGE Aucun outil nécessaire. L’ampoule n’est pas incluse. Pièces jointes : consultez la figure
A. Harp (les modèles peuvent varier)
B. Saddle
C. Ombre (peuvent être emballés en carton séparé)
D. Finial
E. Socket (joint, aucun assemblage ne requis)
F. Plug Cap

Procédure d’assemblage : consultez la figure 1. Insérez la harpe (A) en selle (B). 2. Installer Shade (C) sur faîteau harpe (A) en forme de.
3. Screw (D) sur la harpe (A). 4. Installer ampoule dans la douille selle (E). (Ampoule
150W maximum, Type A) 5. Enlever bouchon bouchon (F) de fiche.

Entretien et nettoyage : 1. Essuyez avec un doux cloth sec. 2. ÉVITER les nettoyants, les tampons à récurer, etc. 3. Before changement d’ampoule, débrancher la lampe et permettre ampoule refroidisse.

DÉPANNAGE :

Problème:

Cause possible:

Réparer en:

Ampoule ne s’allume pas

L’ampoule est brûlée ou endommagée. Le courant ne passe pas dans la lampe.
La lampe n’est pas branchée.

Remplacez l’ampoule. Confirmez que le courant est allumé. Confirmez que la lampe est branchée.

Page 1 of 1

Dans le cas où le luminaire ne fonctionnerait pas après le dépannage, communiquez avec votre centre de décoration Ethan Allen.

CONSERVEZ CES CONSIGNES

12/5/2022

©2018 Ethan Allen Global, Inc.