DESK-E-100W White Electric Single Motor Desk Frame
White Electric Single Motor Desk Frame
SKU: DESK-E-100W
The White Electric Single Motor Desk Frame is an adjustable desk
frame designed to provide flexibility and convenience to its users.
It comes with a motorized leg and a non-motorized leg that can be
adjusted to the desired height with the help of a controller that
comes with the package. The desk frame can support up to 176lbs
(80kg) of weight and can be assembled using the instructions
provided below.
For more information and helpful videos related to this product,
please scan the QR code with your mobile device or visit https://vivo-us.com/products/desk-e-100b.
If you have any queries, please get in touch with us via phone,
email, or live chat. Our customer service team is available Monday
to Friday from 7:00am-7:00pm CST.
- Phone: 309-278-5303
- Email: [email protected]
- Website: www.vivo-us.com
Product Usage Instructions
WARNING!
ELECTRICAL SAFETY INSTRUCTIONS
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT
SUPERVISION IS REQUIRED.
DO NOT EXCEED WEIGHT CAPACITY.
TOOLS NEEDED: Phillips Screwdriver, Drill, Tape
Measure, Allen Wrench (2mm and 5mm)
PACKAGE CONTENTS:
- A (x1) Telescopic Cross Bar Set
- B (x1) Motorized Leg
- C (x1) Non-motorized Leg
- D (x2) Side Brackets
- E (x2) Foot
- F (x1) Sync Rod Center Shaft
- G (x2) Sync Rod Hex Shaft
- H (x16) ST4.8×16
- I (x2) ST2.9×15
- J (x4) M6x8
- K (x12) M6x10
- P (x6) Cable Clip
- L (x8) M6x30
- M (x1) Controller
- N (x1) AC Adapter
- O (x1) Power Cord
- Q (x2) Screw-on Eyelet
- R (x2) 10 Ziptie
- S (x1) 2mm Allen Wrench
- T (x1) 5mm Allen Wrench
ASSEMBLY STEPS:
STEP 1:
Loosely assemble the Telescopic Cross Bar Set (A) making sure
the locking holes are facing up as shown below. Partially insert
M6x8 bolts (J) into the locking holes using Allen Wrench (T),
making sure the Cross Bar is still able to slide freely.
STEP 2:
Attach Cross Bar (A) to both the Motorized Leg (B) and
Non-motorized Leg (C) using M6x10 bolts (K), making sure the
locking bolts are still facing up on the Cross Bar. Tighten with
Allen Wrench (T).
STEP 3:
Attach Side Brackets (D) to both ends of the frame using M6x10
bolts (K). Tighten with Allen Wrench (T).
STEP 4:
Place a foot (E) on each leg as shown below. Attach each foot
using M6x30 bolt (L). Tighten with Allen Wrench (T).
STEP 5:
Attach the Cable Clip (P) to the underside of the Cross Bar (A)
using ST4.8×16 bolts (H), and then attach the AC Adapter (N) to the
Cable Clip (P) using ST2.9×15 bolts (I).
STEP 6:
Insert one of the Sync Rod Hex Shafts (G) through the motor and
into the Motorized Leg (B). NOTE: If the hex does not line up with
the leg, temporarily plug the Motorized Leg (B) and the AC Adapter
(N) into the Controller (M) (see step 10 for details). Then, while
pushing on the hex shaft, very briefly press the up and down arrows
(alternating between the two buttons so the legs will still be even
when assembled) until the shaft slides into the leg.
STEP 7:
Loosen the preinstalled set screws on the Sync Rod Center Shaft
(F) using Allen Wrench (S). Slide the Sync Rod Center Shaft (F)
onto the installed motor Sync Rod Hex Shaft (G) as far as it will
go. Then install the second Sync Rod Hex Shaft (G) into the Sync
Rod Center Shaft (F). Then slide the second Hex Shaft into the
Non-motorized Leg (C).
NOTE: If the hex does not line up with the leg, temporarily plug
the motorized leg (B) and the AC Adapter (N) into the Controller
(M) (see step 10 for details). Then, while pushing on the shaft,
very briefly press the up and down arrows (alternating between the
two buttons so the legs will still be even when assembled) until
the shaft slides into the leg.
STEP 8:
Center the Sync Rod Center Shaft (F) so it rests evenly on both
Sync Rod Hex Shafts (G). When in place, tighten the preinstalled
set screws using the smaller Allen Wrench (S). Note: Be sure not to
pull out the hex shafts from either leg.
STEP 9:
Attach Screw-on Eyelets (Q) to both ends of the frame using
ST4.8×16 bolts (H).
STEP 10:
Attach the Controller (M) to the frame using ST4.8×16 bolts (H).
Plug in the AC Adapter (N) and Power Cord (O) to an electrical
outlet. Connect the Motorized Leg (B) and Non-motorized Leg (C) to
the Controller (M) using the cables provided and secure them with
Zipties (R).
NOTE: Please refer to the user manual for
detailed instructions on how to use the controller to adjust the
desk frame height.
White Electric Single Motor Desk Frame
Instruction Manual
SKU: DESK-E-100W
Scan the QR code with your mobile device or follow the link for helpful videos and specifications related to this product.
Electric Single Motor Desk Frame with Memory Controller
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST
www.vivo-us.com Chat live with an agent!
309-278-5303
WARNING!
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a qualified technician. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual and do not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly, or inappropriate use.
ELECTRICAL SAFETY INSTRUCTIONS
THIS PRODUCT IS POWERED BY ELECTRICITY. IN ORDER TO AVOID BURNS, FIRE AND ELECTRIC SHOCK, PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY. · DO NOT CLEAN PRODUCT WHILE POWER IS CONNECTED. · DO NOT DISASSEMBLE OR REPLACE COMPONENTS WHILE POWER IS CONNECTED. · NEVER OPERATE THE SYSTEM WITH A DAMAGED CORD OR PLUG. PLEASE CONTACT YOUR
SELLER TO REPLACE DAMAGED PARTS. · NEVER OPERATE SYSTEM IN DAMP ENVIRONMENTS OR IF ANY ELECTRICAL COMPONENTS HAVE
MADE CONTACT WITH LIQUIDS. · ALTERATIONS OF THE GIVEN POWER UNIT ARE NOT ALLOWED. · OUTDOOR USE IS PROHIBITED.
WARNING: CHOKING HAZARD
SMALL PARTS – NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
PACKAGE CONTENTS
A (x1) Telescopic Cross Bar Set
B (x1) Motorized Leg
C (x1) Non-motorized
Leg
D (x2) Side Brackets
E (x2) Foot
F (x1) Sync Rod Center Shaft
G (x2) Sync Rod Hex
Shaft
H (x16) ST4.8×16
I (x2) ST2.9×15
J (x4) M6x8
K (x12) M6x10
P (x6) Cable Clip
2
L (x8) M6x30
M (x1) Controller
N (x1) AC Adapter
O (x1) Power Cord
Q (x2) Screw-on
Eyelet
R (x2) 10″ Ziptie
S (x1) 2mm Allen
Wrench
T (x1) 5mm Allen
Wrench
DO NOT EXCEED WEIGHT CAPACITY.
176lbs
Failure to do so may result in serious injury.
(80kg)
TOOLS NEEDED
Phillips
Drill
Tape
Screwdriver
Measure
ASSEMBLY STEPS
STEP 1
Loosely assemble the Telescopic Cross Bar Set (A) making sure the locking holes are facing up as shown below. Partially insert M6x8 bolts (J) into the locking holes using Allen Wrench (T), making sure the Cross Bar is still able to slide freely.
J
A
3
STEP 2
Attach Cross Bar (A) to both the Motorized Leg (B) and Non-motorized Leg (C) using M6x10 bolts (K), making sure the locking bolts are still facing up on the Cross Bar. Tighten with Allen Wrench (T).
C
B K
A
STEP 3
Attach Side Brackets (D) to both ends of the frame using M6x10 bolts (K). Tighten with Allen Wrench (T).
D K
4
STEP 4
Place a foot (E) on each leg as shown below. Attach each foot using M6x30 bolt (L). Tighten with Allen Wrench (T).
L E
STEP 5
FOR VIVO DESKTOP: Adjust frame width until the Side Bracket (D) holes line up with the pre-drilled holes on the desktop. Adjust center crossbar section until all M6x8 bolts (J) are able to make contact, then fully tighten using Allen Wrench (T). To attach the desktop, refer to the manual included with your desktop. Set aside x2 of the ST4.8×16 screws (H) for mounting the AC Adapter (N). FOR OTHER DESKTOP: Adjust the frame to the desired width while making sure the overhang does not exceed 10″ on either side. Adjust center crossbar section until all M6x8 bolts (J) are able to make contact, then fully tighten using Allen Wrench (T). Mark and drill pilot holes to a depth of 3/8″ (10mm) using a 1/8″ (3mm) bit where the Side Brackets (D) align on the desktop. Secure the frame using ST4.8×16 screws (H) to the desktop. Set aside x2 of the ST4.8×16 screws (H) for mounting the AC Adapter (N).
H
J
D
STEP 6
Insert one of the Sync Rod Hex Shafts (G) through the motor and into the Motorized Leg (B). NOTE: If the hex does not line up with the leg, temporarily plug the Motorized Leg (B) and the AC Adapter (N) into the Controller (M) (see step 10 for details). Then, while pushing on the hex shaft, very briefly press the up and down arrows (alternating between the two buttons so the legs will still be even when assembled) until the shaft slides into the leg.
B
G
5
STEP 7
Loosen the preinstalled set screws on the Sync Rod Center Shaft (F) using Allen Wrench (S). Slide the
Sync Rod Center Shaft (F) onto the installed motor Sync Rod Hex Shaft (G) as far as it will go. Then install
the second Sync Rod Hex Shaft (G) into the Sync Rod Center Shaft (F). Then slide the second Hex Shaft
into the Non-motorized Leg (C).
NOTE: If the hex does not line up with the leg, temporarily plug the motorized leg (B) and the AC
Adapter (N) into the Controller (M) (see step 10 for details). Then, while pushing on the shaft, very briefly
press the up and down arrows (alternating between the two buttons so the legs will still be even when
assembled) until the shaft slides into the leg.
F
C
G
F
G
G
STEP 8
Center the Sync Rod Center Shaft (F) so it rest’s evenly on both Sync Rod Hex Shafts (G). When in place, tighten the preinstalled set screws using the smaller Allen Wrench (S). Note: Be sure not to pull out the hex shafts from either leg.
G
F
SET SCREWS
G
STEP 9
Attach the Controller (M) to the desktop using ST2.9×15 screws (I), making sure it is on the side of the Motorized Leg (B).
B
I M
6
STEP 10
Plug cables together as shown below. Tidy up cables using Cable Clips (P). Attach AC Adapter (N) to desktop using ST4.8×16 screws (H), the Screw-on Eyelets (Q), and 10″ Zipties (R) as shown below. Note: A desk reset is required before use. Refer to the Controller User Guide for operational instructions. Ensure there is enough slack in the cables at the lowest and highest positions before use.
M
2.75″ (70mm)
N
P
R
O
N
STEP 11
If necessary, adjust foot pads at the bottom of foot (E) to level the desk.
H Q
E
E
CAUTION!
Do not exceed desk weight limit.
Keep area of vertical motion free of obstacles.
Keep weight on desk balanced for correct operation and longer life of components.
Leave enough slack in cables to allow for full range of vertical motion.
Failure to follow these instructions may result in property damage and/or personal injury.
7
Love your new VIVO setup and want to share? Tag us in your photo! @vivo_us
LAST UPDATED: 03/08/2022 REV3.1
Open Monday – Friday 7:00am – 7:00pm CST, our dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact us. We are happy to replace parts to ensure you have a fully functioning product.
309-278-5303
AVG. RESOLUTION TIME (within office hrs): 5M 4S
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within office hrs): < 15 M
AVG. RESPONSE TIME (within office hrs): 1HR 8M – 23% within < 15m – 38% within < 30m – 61% within < 1hr – 83% within < 2hr – 92% within < 3hr
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
Register a .US.COM domain today!
VIVO - Desks, Monitor Mounting, and More Home & Office Solutions – VIVO - desk solutions, screen mounting, and more
Electric Single Motor Desk Frame with Memory Controller – VIVO - desk solutions, screen mounting, and more
