Sena 10s Motorcycle Bluetooth Communication System User Manual

10S Motorcycle Bluetooth Communication System

Product Information

• Product Name: 10S
• Description: Bluetooth headset with intercom
  functionality
• Features:
  • Charging with LED indicators
  • Power on/off
  • Volume adjustment
  • Battery check
  • Phone and music pairing
  • Music control (play/pause, track forward/back)
  • Mobile phone call handling (answering, ending, voice dial,
    speed dial, call rejection)
  • Intercom pairing and communication
  • Configuration settings menu
  • Sena Device Manager for headset configuration
  • Troubleshooting and factory reset options
  • FCC compliance and safety approvals

Product Usage Instructions

Charging

Connect the headset to a power source using the provided cable.
While charging, the LED indicator will be red. Once fully charged,
the LED indicator will turn blue.

Power On/Off

To power on the headset, press and hold the Jog Dial and Phone
Button for 1 second. To power off, tap the Jog Dial and Phone
Button.

Volume Adjustment

To increase or decrease the volume, rotate the Jog Dial
clockwise or counterclockwise.

Battery Check

To check the battery level, press and hold the Jog Dial and
Phone Button for 1 second.

Phone and Music Pairing

1. Press and hold the Jog Dial and Phone Button for 1 second.
2. On your mobile phone, search for Bluetooth devices and select
   the headset from the list of detected devices.
3. Enter 0000 as the PIN when prompted. Note that some mobile
   phones may not ask for a PIN.

Music Operation

• To play or pause music, press and hold the Jog Dial for 1
  second.
• To skip to the next or previous track, rotate the Jog Dial
  while pressing it clockwise or counterclockwise.

Mobile Phone Call Making and Answering

• To answer a call, tap the Phone Button.
• To end a call, tap the Phone Button.
• To initiate voice dialing, tap the Phone Button.
• To speed dial, double tap the Phone Button.
• To reject a call, press and hold the Jog Dial for 2
  seconds.

Intercom

Note: Intercom functionality requires two headsets.

1. Press and hold the Jog Dial of both headsets for 5 seconds
   until the red LEDs of both units start flashing rapidly.
2. Simply tap the Jog Dial of any one of the two headsets to pair
   them for intercom communication.

To start or end an intercom conversation, tap the Jog Dial of
either headset.

Setting

To access the configuration menu, press the Jog Dial for 10
seconds.

Using the Sena Device Manager

1. Connect the headset to your computer using a USB cable.
2. Launch the Sena Device Manager software.
3. Click on DEVICE SETTING to configure the headset settings.

For detailed instructions on downloading the Sena Device
Manager, please refer to the leaflet included in the package.

Troubleshooting

Factory Reset

If you want to restore the headset to factory default settings,
press and hold the Phone Button for 10 seconds and tap the Jog
Dial. The headset will automatically restore the default settings
and turn off.

Certification and Safety Approvals

FCC Compliance Statement

To ensure compliance with FCC regulations:

• Increase the separation between the equipment and the
  receiver.
• Connect the equipment to an outlet on a different circuit from
  the receiver.
• Consult the dealer or an experienced radio/TV technician for
  assistance.

FCC RF Exposure Statement

This equipment complies with FCC radiation exposure limits.
Users must follow specific operating instructions to comply with RF
exposure regulations. The antenna used for this transmitter must
not transmit simultaneously with any other antenna or transmitter,
except as allowed by FCC multi-transmitter product procedures. When
equipped, maintain a distance of 40mm between the antenna and one’s
head surface.

10S Manual
Charging
Red LED: Charging Blue LED: Fully charged
Power On/Off
Press and hold the Jog Dial and Phone Button for 1 second Tap the Jog Dial and Phone Button.
Volume Adjustment
Increase/Decrease the volume : Rotate the Jog Dial clockwise or counterclockwise
Battery Check

Phone, Music Pairing
Initially Pairing the headset The headset will automatically enter the phone pairing mode when you initially turn on the headset or in the following situation: · Rebooting after executing Factory Reset
1. Press and hold the Jog Dial and Phone Button for 1 second. 2. Search for Bluetooth devices on your mobile phone. Select the headset in the list of the devices
detected on the mobile phone. 3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
Music Operation
Play or pause music: Press and hold the Jog Dial for 1 second. Track forward/ back: Rotate while pressing the Jog Dial clockwise or counterclockwise.
Mobile Phone Call Making and Answering
Answering a call: Tap the Phone Button Ending a call: Tap the Phone Button Voice dial: Tap the Phone Button Speed dial: Double tap the Phone Button Rejecting a call: Press and hold the Jog Dial for 2 seconds.
Intercom
Intercom Pairing 1. Press and hold the Jog Dial of two headsets for 5 seconds until red LEDs of both units start to flash rapidly. 2. Simply tap the Jog Dial of any one of the two headsets.
Intercom Start/End : Tap the Jog Dial.

Setting
Configuration Menu: Press the Jog Dial for 10 seconds.
Using the Sena Device Manager
Connect the headset to your computer via a USB cable. Launch the Sena Device Manager and click DEVICE SETTING to configure the headset settings.
For details about downloading the Sena Device Manager, please refer to the leaflet included in the package.
Troubleshooting
Factory Reset
If you want to restore the headset to factory default settings, Press and hold the Phone Button for 10 seconds and tap the Jog Dial . The headset automatically restores the default settings and turns off.
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antennae

-Increase the separation between the equipment and the receiver -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. The antenna used for this transmitter must not transmit simultaneously with any other antenna or transmitter, except in accordance with FCC multi-transmitter product procedures. When equipped, the distance between antenna and one’s head surface is 40mm.
FCC Caution Any changes or modifications to the equipment not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment. Certification et homologation de sécurité Déclaration de conformité FCC Cet appareil est en conformité avec la partie 15 des règles de la FCC. Son fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas créer d’interférences préjudiciables et (2) Cet appareil doit accepter toutes les interférences reçues, y compris celles qui pourraient entraver son bon fonctionnement. Cet équipement a été testé et jugé conforme aux limites pour un appareil numérique de classe B, conformément à la partie 15 des règles de la FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles dans une installation résidentielle. Cet équipement génère et utilise de l’énergie radio fréquence et, s’il n’est pas installé et utilisé conformément. aux instructions, il peut occasionner des interférences nuisibles au niveau des communications radios. Cependant, il n’existe aucune garantie que ces interférences ne se produiront pas dans une installation particulière. Si cet équipement génère des interférences nuisibles à la réception de la radio ou de la télévision (ce qu’il est possible de déterminer en mettant l’équipement hors tension, puis sous tension), l’utilisateur est invité à suivre une ou plusieurs des mesures suivantes pour corriger le problème des interférences en prenant l’une des mesures suivantes : -Modifier l’emplacement ou l’orientation de l’antenne de réception. -É loigner l’appareil du récepteur. -Brancher l’appareil sur une prise située sur un circuit différent de celui du récepteur. -Consulter le revendeur ou un technicien expérimenté pour obtenir de l’aide.
É noncé FCC sur l’exposition aux radiations RF Cet équipement est conforme aux réglementations FCC d’exposition aux radiations définies pour un environnement non contrôlé. Les utilisateurs doivent respecter les instructions d’exploitation spécifiques

pour répondre aux exigences de conformité sur l’exposition aux RF. L’antenne utilisée pour cet appareil ne doit pas fonctionner en même temps qu’une autre antenne ou émetteur, sauf s’il y a conformité avec les procédures FCC des produits multi-émetteurs. Cet appareil est conforme à l’exigence d’exposition aux RF. Lorsque équipé, la distance entre l’antenne et la surface de la tête est de 40mm.
Précautions FCC Tout changement ou modification non expressément approuvé par la partie chargée de la mise en conformité peut annuler le droit de l’utilisateur à utiliser l’équipement.
Industry Canada(IC) Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)this device may not cause interference, and (2)this device must accept any interference, including interference that may cause undesired operation of the device. Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisee aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d’en compromettre le fonctionnement.
IC RF Exposure Statement Cet équipement est conforme aux limites d’exposition aux radiations de la FCC définies pour un environnement non contrôlé. Les utilisateurs finaux doivent suivre les instructions d’utilisation spécifiques pour satisfaire à la conformité d’exposition RF. L’antenne utilisée pour cet émetteur ne doit pas émettre simultanément avec d’autres antennes ou émetteurs, sauf en conformité avec les procédures FCC relatives aux produits multi-émetteurs. Lorsque équipé, la distance entre l’antenne et la surface de la tête est de 40mm.