User Manual 35in Computer Monitor
Model: V3L6W

Notices————————————————————————————————————————————– 3 Product introduction ——————————————————————————————————————- 3
Packing list—————————————————————————————————————————- 3 Instructions for use———————————————————————————————————————- 4
Description of buttons————————————————————————————————————- 4 Explanation of indicators———————————————————————————————————- 4 Adjusting the monitor————————————————————————————————————- 4 Installation of base———————————————————————————————————————- 5 Cable connection———————————————————————————————————————— 6 OSD menu——————————————————————————————————————————— 7 Menu description——————————————————————————————————————- 7 Basic parameters———————————————————————————————————————— 10
2

Notices

Before using this product, please read this User Manual carefully and keep it well

Keep the monitor away from water sources or damp places, such as bath rooms, kitchens, basements and swimming pools.
Make sure the monitor is placed on a flat surface. lf the monitor falls down, it may cause human injury or device damage. Store and use the monitor in a cool, dry and well ventilated place, and keep it away from emission and heat sources. Do not cover or block the vent hole in the rear casing, and do not use the product on a bed, sofa, blanket or similar objects. The range of the supply voltage of the monitor is printed on the label on the rear casing. If it is impossible to determine the supply voltage, please consult the distributor or local power company.
lf the monitor will not be used for a long period, please cut off the power supply to avoid electric shock in rainy days and damage due to abnormal supply voltage.
Please use a reliable earthing socket, do not overload the socket, or it may cause fire or electric shock.
Do not put foreign matters into the monitor, or it may cause short circuits resulting fire or electric shock.
Do not disassemble or repair this product by self to avoid electric shock. If faults occur, please contact the after-sales service directly.
Do not pull or twist the power cable forcedly.
There is a polarizer layer (not a protective film) on the surface of the screen. Do not peel it off, or the product may be damaged and the warranty will be invalid.

Product introduction
Packing list
Please check that the package of the monitor contains all parts. The color and shape of parts may vary with models. Figures in this User Manual are for reference only. Wires supplied may vary with purchased products. Figures in this User Manual are for reference only.

Display screen

Stand

Base

(PM4)Screws

(KM4)Screws

Power Cable

DP cable

User Manual

Note: The redundant screws are used as spare screws. 3

Instructions for use
Description of buttons

1

Menu button: Press to enter sub-menus.

2

Down button: Press to move down in the menu.

3

Up button: Press to move up in the menu.

4

Exit/hot key: Press to return to the previous menu.

5

Power button: Press to turn on/off the monitor.

Explanation of indicators
Indicator Light
Adjusting the monitor

Indicator light: A steady blue light indicates that the power is on and the monitor is operating normally. Blue light flashes to indicate There is no video source and no horizontal or vertical signal or low voltage is detected. Make sure your computer is turned on and all video cables are fully plugged in and/or connected.
Tilting angle -5.0°(±2.0°)- +15°(±2.0°)

4

Installation of base
Unpack the carton, remove the foam, and lay the monitor flat on the table. Keep the foam under the monitor until you install the stand. 1. Take out the base and bracket and tighten them with screws. Take out the shaft assembly and lock it with the base of the bracket with screws.
Tighten with two screws
Tighten with three screws 2. Remove the upper foam cover (note: the machine cannot leave the lower foam cover).
Use the assembled base bracket assembly to align the slot of the machine and buckle down . (note: press and hold the quick release button with your fingers to take out the base bracket assembly).
3. Press and hold the quick release button with your fingers to remove the base stand assembly.
4. After assembly, simply hold the stand with hand to stand the monitor upright.
Do not press the LCD
Note: During standing of the whole monitor, do not press the liquid crystal screen with hand to avoid damage to the screen.
5

Installation of mount
1.Open the carton package, take out the foam and put it flat on the table top.
2.Remove the upper foam box, take out the film-coated bag of the fuselage, and put the fuselage into theoriginal lower foam box again.
3.Find the PM4*16 screws from the accessory kit, and lock the screws and wall-mounted components in the threaded holes of the rear shell. when disassembling the wall-mounted components, the monitor cannot leave the foam box to prevent the screen from cracking.
Wall Mount Screws(not supplied) 4. Note: Hang the assembled product on a hard wall. Do not pinch the screen with your hands during the
hanging process to avoid damaging the screen. Mount (not supplied)
Notes: To prevent the monitor on the mount from failing, please install it firmly and protect it fully. Do not place or hang any object on the mount, and the using height of the mount should be less than 2 meters.
6

Cable connection

* The bottom interface configuration at the back of the monitor varie with products.
* Note: If the power cable or signal cable is damaged, you must replace it with special soft cables or special components purchased from the manufacture or maintenance department.

HDMI interface
Use the HDMI cable to connect the HDMI IN interface of the product to the HDMI OUT interface of a PC.

Use the HDMI-DVI cable to connect the HDMI IN interface of the product to the DVI OUT interface of a PC.

DP interface
Use the DP cable to connect the DP IN interface of the product to the DP OUT interfac of a PC.

AUDIO OUT
Connect audio outputting devices such as earphones to the AUDIO OUT interface.

AC interface
Please connect the power cable plug to the corresponding port of the mo nitor, and connect the other end to a properly grounded power outlet.

OR

7

OSD menu
Menu description
The color and shape of the OSD menu of the actual computer may be slightly different from them shown in the figure. Specifications of the OSD menu may change with improvements of functions without prior notice. The screen display (OSD) menu can be used to adjust settings of the monitor and is shown on the screen after the monitor is powered on and the button is pressed. 1. Press one of the buttons ( M, , , E, ) to activate the browser screen.
2. Press ( ) to enter the OSD screen.
3. Press or to browse through the functions. -Select the desired function, then press the button to enter the submenu -Press or to browse the sub-menus, and then press the key to confirm the selection of the desired function. -Press or to select an option, then press to confirm the setting and exit the current menu. 4. Press to exit the menu interface
8

Functions of the monitor vary with models, and the functions in this manual are for reference only.

Input Source

DP1 DP2 HDMI1 HDMI2

None None None None

Brightness

0-100

Brightness/ Contrast

Blacklevel Contrast DCR

0-100 0-100 On/Off

Gamma

1.8/2.0/2.2/2.4/2.6

Pictrue Mode

Standard/Photo/Movie/Game/FPS/RTS

Color Setting

Color Temperature Warm/Cool/User Low Blue Light 0-100

Hue

0-100

Saturation

0-100

Sharpness

0-100

Response Time Off/High/Middle/Low
Picture Quality Noise Reduction Off/High/Middle/Low Setting
Super Resoultion Off/High/Middle/Low
Dynamic Luminous On/Off Control

Display Audio

Aspect Ratio LedMode Mute Volume Audio Source

Wide Screen/4:3/1:1/Auto Flicker/Normal/Off On/Off 0-100 DP1/DP2/HDMI1/HDMI2

Multi-Window

Off/PIP Mode/PBP 2Win

Sub Win2 Input Multi-Window PIP Size

DP1/DP2/HDMI1/HDMI2 Small/Medium/Large

PIP Position Swap Language OSD H-Position

TopRight/TopLeft/BottomRight/BottomLeft None English////Español//Francais 0-100

OSD

OSD V-Position 0-100 OSD Transparency 0-100

OSD Time Out 5-100

OSD Rotation

Normal/90/180/270

DP Version

DP1.1/DP1.2/DP1.4

Other

Adaptive-Sync HDR

On/Off On/Off/Auto Detect

Reset

None

9

Basic parameters

Product Name

Liquid Crystal Display

Product model Screen Size

V3L6W 35 inches

Aspect Ratio Viewing Angle

21:9 178°(H) / 178°(V)

Pixel pitch

0.2382 (H) x 0.2402 (V) mm

Contrast ratio

2500:1(Typ)

Colors Resolution

16.7M 3440 x 1440

Maximum refresh rate

120Hz

Power specifications

100-240V~,50/60Hz,2.0A The standard voltage and current may vary with countries, please refer to the label at the back of the product.

Product Dimentions Without base 837.39 x377.93 x 120.79 mm/ approx. 6.78kg

Normal base

With base

837.39 x 484.85 x 245.11mm/ approx. 8.9 kg

Carton size 928x202x483mm

Gross Weight 10.5KG

Tilting angle

Forward titling: -5°±2° ; Backward tilting : 15°±2°

Rotation angle Height angle Pivot angle Environmental conditions

Action Storage

NA

NA

NA Temperature: 0°C~ 40°C (32°F ~ 104°F) Temperature: -20°~ 60° (-4°F ~ 140°F)

Humidity: 10%~90% RH (non-condensing) Humidity: 5%~95% RH (non-condensing)

The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing Administrator, Inc. in the United States and other countries.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, (2)this device must accept any interference received, (3)including interference that may cause undesired operation. CAN ICES-3 (B)/NMB-3(B)

Made in China
10

V3L6W

Fiodio

140*210mm

Fiodio 2022.3.22

120G80G, , SGSROHS

V01

: