6 Tier A Frame Dumbble Rack
Product Information:
The 6-Tier A-Frame Dumbbell Rack is designed to provide a safe
and secure storage solution for your dumbbells. It meets industry
standards for stability when used for its intended purpose in
accordance with the instructions provided. The owner is responsible
for ensuring that all users of this rack are adequately informed of
all precautions. The manufacturer is not responsible for any injury
or death caused by improper use or improper assembly. This product
is designed and intended for consumer/home use only in an indoor
environment. It is not recommended for commercial, rental, or
institutional settings. The safety and integrity designed into this
rack can only be maintained when the equipment is regularly
examined for damage and repaired.
Product Usage Instructions:
Before beginning any exercise program, consult your physician,
especially if you are over the age of 35 or have pre-existing
health conditions. Keep children and pets away from this product at
all times. Place the rack on a clean, flat, and level surface
indoors, away from moisture and any other water. Do not use this
rack for support during stretching or attaching resistance bands,
straps, ropes, or any other means, as it may result in serious
injury. Inspect and properly tighten all parts regularly. Replace
any worn parts immediately.
Maintenance:
It is the sole responsibility of the user/owner to ensure that
regular maintenance is performed. Worn or damaged components should
be replaced immediately, and the equipment should not be used until
the repair is made. Wipe the rack regularly to prevent the
accumulation of dust. Use a dry cloth to clean the metal frames.
Avoid acid chlorine-based cleaners and those containing abrasives
as these could scratch or damage the equipment. Check regularly to
ensure all parts are tight and in working condition. If a part is
damaged, do not use until the parts are replaced or repaired.
Assembly:
- Connect the two U-Frame Supports (#5) to the Center Cross Base
(#6) using two bolts (#10), four washers (#8), and two nuts (#9) on
each side. Insert the end caps (4) on the U-Frame Supports (#5) if
not already attached. - Insert the two Main Frames (#1) into the U-Frame Supports (#5)
using two bolts (#7), four washers (#8), and two nuts (#9) on each
side. - Place the Top Cap (#3) onto the Main Frames (#1), secure them
with four bolts (#7), eight washers (#8), and four nuts (#9). Place
the 24 Dumbbell Cradles (#2) onto the dumbbell slots to cushion the
dumbbell handles. Secure each cradle with the included 24
plugs. - Fully Tighten Your Hardware: These particular nuts are lock
nuts, so they are near impossible to hand-tighten. You need the
included allen wrench on one end tightening the bolt, along with a
wrench (not included) around the nut on the other end to fully
tighten everything together.
WARNING
Serious injury or death can occur if caution is not used. To reduce the risk of serious injury, read the following instructions and warnings. Keep these instructions for future reference. Before beginning any exercise program, consult your physician. This is especially important for those over the age of 35 or those with pre-existing health conditions.
1. This product meets industry standards for stability when used for it’s intended purpose in accordance with the instructions provided.
2. Using this rack for support during stretching or attaching resistance bands, straps, ropes, or any other means to this rack may result in serious injury.
3. It is the responsibility of the owner to ensure that all users of this rack are adequately informed of all precautions.
4. Inspect and properly tighten all parts regularly. Replace any worn parts immediately.
5. Keep children and pets away from this product at all times. 6. Keep this product indoors, away from moisture and any other water. 7. Place the rack of a clean, flat, and level surface. 8. Manufacturer is not responsible for any injury or death caused by improper
use or improper assembly. 9. This product is designed and intended for consumer/home use only in an
indoor environment. Do not use it in a commercial, rental, or institutional setting.
MAINTENANCE
The safety and integrity designed into this rack can only be maintained when the equipment is regularly examined for damage and repaired. It is the sole responsibility of the user/owner to ensure that regular maintenance is performed. Worn or damaged components should be replaced immediately and stop using the equipment until the repair is made.
1. Wipe rack regularly to prevent accumulation of dust. 2. Use a dry cloth to clean the metal frames. 3. Avoid acid chlorine based cleaners and those containing abrasives as these could
scratch or damage the equipment. 4. Check regularly to ensure all parts are tight and in working condition. If a part is
damaged, do not use until the parts are replaced or repaired.
OWNERS MANUAL
6-Tier A-Frame Dumbbell Rack
A S S E M B LY
STEP 1 Connect the two U-Frame Supports (#5) to the Center Cross Base (#6) using two bolts (#10), four washers (#8) and two nuts (#9) on each side. Insert the end caps (4) on the U-Frame Supports (#5) if not already attached.
STEP 2 Insert the two Main Frames (#1) into the U-Frame Supports (#5) using two bolts (#7), four washers (#8), and two nuts (#9) on each side.
STEP 3 Place the Top Cap (#3) onto the Main Frames (#1), secure them with four bolts (#7), eight washers (#8), and four nuts (#9). Place the 24 Dumbbell Cradles (#2) onto the dumbbell slots to cushion the dumbbell handles. Secure each cradle with the included 24 plugs.
Fully Tighten Your Hardware: These particular nuts are lock nuts, so they are near impossible to hand-tighten. You need the included allen wrench on one end tightening the bolt, along with a wrench (not included) around the nut on the other end to fully tighten everything together.
PART LIST
1) Main Frame (X2) 2) Dumbbell Cradles (X24) 3) Top Cap (X1) 4) End Caps (X4) 5) U-Frame Supports (X2) 6) Center Cross Base (X1)
7) Bolts M10x19mm (X8) 8) Washers M10 (X24) 9) Nuts M10 (X12) 10) Bolts M10x86mm (X4) 11) Allen Wrench (X1) 12) Cradle Plugs (X24)
Not included: Wrench for Self-Locking Nuts
