GHO 26-82 Wired Planer
Product Information
The GHO 26-82 is a planer tool designed for planing, beveling
edges, and rebating of firmly supported wooden materials such as
beams and boards. It has a maximum planer width of 82mm and weighs
approximately 2.6kg without accessories. The tool has a rated power
of 710W, output power of 400W, and a no-load speed of 16,500rpm.
The machine is equipped with a safety switch and an on/off switch
for easy operation. It is recommended to wear safety glasses,
protective gloves, and sturdy shoes while using the machine.
Product Usage
- Before using the machine, ensure that the voltage of the power
source matches the voltage specified on the nameplate of the
machine. - Wear safety glasses, protective gloves, and sturdy shoes while
using the machine. For long hair, wear hair protection and work
only with closely fitting clothes. - Connect the machine to a residual current device (RCD) with an
actuating current of 30 mA maximum if used in the open. Use only
extension cables that are approved for outdoor use. - Hold the machine firmly while working and ensure a secure
stance. Keep hands away from rotating parts and do not allow
fingers to enter the chip ejector. - The planer shoe must lay flat on the surface when working.
Never plane over metal objects such as nails or screws. - Use only sharp planing blades and always direct the cable to
the rear away from the machine. - Apply the machine to the workpiece only when switched on.
Always switch the machine off and wait until it has come to a
standstill before placing it down. - Never use the machine with a damaged cable and never allow
children to use the machine. - Bosch is only able to ensure perfect operation of the machine
if the original accessories intended for it are used.
EURO · Printed in Malaysia · BA 2 609 140 180 · GHO 26-82 · Titelseite · OSW 02/04 2 609 140 180.book Seite 1 Mittwoch, 3. April 2002 9:19 09
Bedienungsanleitung Operating Instructions Instructions d’emploi Instrucciones de servicio Manual de instruções Istruzioni d’uso Gebruiksaanwijzing Betjeningsvejledning Bruksanvisning Brukerveiledningen Käyttöohje O µ Kullanim kilavuzu
GHO 26-82
Deutsch English Français Español Português Italiano Nederlands Dansk Svenska Norsk Suomi E Türkçe
Downloaded from www.Manualslib.com manuals search engine
Euro · BA 2 609 140 180 · GHO 26-82 · Leerseite · OSW 02/04 2 609 140 180.book Seite 2 Mittwoch, 3. April 2002 9:19 09
2 · 2 609 140 180 · 02.04
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · Zubehörseite · OSW 02/04 2 609 140 180.book Seite 3 Mittwoch, 3. April 2002 9:19 09
1 608 132 006
2 608 635 376 (1x) 2 608 635 350 (2x)
2 607 000 102
2 605 411 035
2 607 001 077 (0 – 45°)
2 605 438 532
2 605 702 022
3 · 2 609 140 180 · 02.04
Ø 35 mm
3 m 2 607 000 837 5 m 1 609 202 230
GAS …
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · Bildseite 1 · OSW 02/04 2 609 140 180.book Seite 4 Mittwoch, 3. April 2002 9:19 09
2* 1*
7 8 3 6 5
4
3
9 10
11 12
4 · 2 609 140 180 · 02.04
13*
16
14
15
17*
15
16
18
14
GHO 26-82
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · Bildseite 2 · OSW 02/04 2 609 140 180.book Seite 5 Mittwoch, 3. April 2002 9:19 09
A
19*
B
20* Ø-35-mm
3
C
25
26 11
22 23 24
E
D
F
11 21
11 25
10
28
9
5 · 2 609 140 180 · 02.04
29 28 27
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · GB · OSW 02/04 2 609 140 180.book Seite 1 Mittwoch, 3. April 2002 9:19 09
Tool Specifications
Planer
GHO 26-82
Order number
0 601 594 1..
Rated power
[W] 710Output power
[W] 400No-load speed
[rpm] 16 500Planing depth
[mm] 0 2.6Rebating depth
[mm] 0 9.0Planer width (max.)
[mm] 82Weight (without
accessories) approx.
[kg] 2.6Protection class
/ II
Please observe the order number of your machine. The trade names of the individual machines may vary.
Machine Elements
1 Fastening bolt for rebating depth stop* 2 Rebating depth stop* 3 Chip ejector (alternatively right/left) 4 Adjustment knob for planing depth 5 Planing depth scale 6 Change-lever for direction of chip ejection 7 Switch lock 8 On/Off switch 9 Belt cover 10 Screw for belt cover 11 Planer shoe 12 V-grooves 13 Parallel guide* 14 Fastening bolt for parallel and angle guide 15 Locking nut for adjustment of rebating width 16 Scale for rebating width 17 Angle guide* 18 Locking nut for angle adjustment 19 Dust/wood chip bag with adapter* 20 Vacuum hose* 21 Blade protector 22 Blade head 23 Blade-clamping element 24 Fastening screws for planer blade 25 Allen key 26 HM/TC planer blade 27 Large belt pulley 28 Drive belt 29 Small belt pulley
* Not all of the accessories illustrated or described are included as standard delivery.
For Your Safety
Working safely with this machine is possible only when the operating and safety information are read completely and the instructions contained therein are strictly followed. Before using for the first time, ask for a practical demonstration. In addition, the general safety notes in the enclosed booklet must be observed.
Wear safety glasses, protective gloves and sturdy shoes.
For long hair, wear hair protection. Work only with closely fitting clothes.
If the mains cable is damaged or cut through while working, do not touch the cable but immediately pull the mains plug. Never use the machine with a damaged cable.
Connect machines that are used in the open via a residual current device (RCD) with an actuating current of 30 mA maximum. Use only extension cables that are approved for outdoor use.
Always direct the cable to the rear away from the machine.
Apply the machine to the workpiece only when switched on.
Use only sharp planing blades.
Always hold the machine firmly when working and ensure a secure stance.
Keep hands away from rotating parts.
The planer shoe 11 must lay flat on the surface when working.
Never plane over metal objects such as nails or screws.
Do not allow fingers to enter the chip ejector 3.
Always switch the machine off and wait until it has come to a standstill before placing it down.
Never allow children to use the machine.
Bosch is only able to ensure perfect operation of the machine if the original accessories intended for it are used.
11 · 2 609 140 180 · TMS · 08.03.02
English – 1
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · GB · OSW 02/04 2 609 140 180.book Seite 2 Mittwoch, 3. April 2002 9:19 09
Intended Use
The machine is intended for planing of firmly supported wooden materials, such as beams and boards. It is also suitable for beveling edges and rebating.
Initial Operation
Observe correct mains voltage: The voltage of the power source must agree with the voltage specified on the nameplate of the machine. Equipment marked with 230 V can also be connected to 220 V.
Switching On and Off
To start the machine, press the safety switch against starting 7 first, then press and hold the On/Off switch 8.
To switch off the machine, release the On/Off switch 8.
For safety reasons the On/Off switch of the machine cannot be locked; it must remain pressed during the entire operation.
Adjusting the Planing Depth
The planing depth can be adjusted variably from 0 2.6 mm with the adjustment knob 4, using the planing depth scale 5 (scale graduation = 0.1 mm):
Rotation in counterclockwise direction
=
reduces the planing depth
Rotation in clockwise direction creases the planing depth
= in-
Dust/Chip Extraction (see figure A )
The dust that is produced while working can be detrimental to health, inflammable or explosive. Suitable safety measures are required. Examples: Some dusts are regarded as carcinogenic. Use suitable dust /chip extraction and wear a dust respirator.
Clean the chip ejector 3 regularly. Use a suitable tool (e. g. piece of wood, compressed air, etc.) to clean clogged chip ejector. Do not allow fingers to enter the chip ejector 3.
To ensure optimum extraction of dust /wood chips, attach the vacuum hose 20 or the dust / wood chip bag 19 tightly onto the chip ejector 3.
External Dust Extraction
The chip ejector 3 fits on both sides for direct connection of the Bosch vacuum hose Ø – 35 mm 20 (accessory). When using other vacuum hose systems a suitable extraction adapter may be required.
The vacuum cleaner must be suitable for the material to be worked. When vacuuming dry dust that is especially detrimental to health or carcinogenic, use a special vacuum cleaner.
Integrated Dust Extraction
A dust/wood chip bag 19 (accessory) can be used for smaller jobs.
Empty the dust/wood chip bag regularly. Remove the dust/wood chip bag, open the zipper and empty the dust/wood chip bag.
Choice of Chip Ejector Side (Right / Left)
The chip ejector 3 can be switched to the right or left with the change lever 6.
Always press the change lever until it engages in the end position.
The selected ejector direction is marked with an arrow.
Operating Instructions
Blade Protector (see figure B )
The integrated blade protector 21 allows the machine to be set down directly after operation, without danger of damaging the working surface or the planer blade.
When planing, the blade protector 21 is tilted upwards thus enabling full contact of the rear part of the planer shoe 11.
12 · 2 609 140 180 · TMS · 08.03.02
English – 2
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · GB · OSW 02/04 2 609 140 180.book Seite 3 Mittwoch, 3. April 2002 9:19 09
Planing (see figure B )
Set the required planing depth and place the front part of the planer shoe 11 against the workpiece.
Caution! Danger of kickback!
Apply the machine to the workpiece only when switched on.
Switch the machine on and guide the machine with an even feed over the surface to be planed.
To achieve high-grade surfaces, work only with low feed and apply pressure on the centre of the planer shoe.
When machining hard materials (e. g. hardwood) as well as when utilising the maximum planer width, set only low planing depths and reduce planer feed, as required. Repeat the planing several times.
Excessive feed reduces the surface quality and can lead to rapid clogging of the chip ejector.
Only sharp blades achieve good cutting capacity and give the machine longer life.
Continuing interrupted planing
The integrated blade protector 21 also allows for continued planing at any given location on the workpiece after an interruption:
With the blade protector folded down, place the machine on the location of the workpiece where the planing is to be continued.
Switch the machine on.
Apply the supporting pressure onto the front part of the planer shoe and slowly push the machine forwards (). This tilts the blade protector 21 up () so that the rear part of the planer shoe 11 faces on the workpiece again.
Guide the machine alongside the surface to be planed () with an even feed.
Beveling Edges
The V-grooves 12 in the front planer shoe 11 allow quick and easy beveling of workpiece edges. Depending on required bevel width, use the corresponding V-groove.
12
45°
For this, place the planer with the V-groove 12 onto the edge of the workpiece and guide along the edge.
Using the Parallel/Angle Guide (Accessory)
Mount parallel guide 13 or angle guide 17 to the machine using fastening bolt 14 and rebating depth stop 2 using fastening bolt 1. Loosen locking nut 15 and adjust the required rebating width with the scale 16. Retighten locking nut 15 again. Adjust the required rebating depth accordingly with the rebating depth stop 2. Carry out the planing procedure several times, until the required rebating depth is reached. Pay attention that the planer is guided with sideward supporting pressure.
13 · 2 609 140 180 · TMS · 08.03.02
9 mm max
m8a2xmm
Beveling (only angle guide 17) When beveling rebates and surfaces, adjust the required slope angle with the angle adjustment 18.
English – 3
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · GB · OSW 02/04 2 609 140 180.book Seite 4 Mittwoch, 3. April 2002 9:19 09
Replacing the Planer Blade (HM / TC)
Before any work on the machine itself, pull the mains plug.
Be cautious when replacing the planer blades: Possible danger of injury due to the sharp cutting edges of the planer blades! Do not grasp the planer blades by the cutting edges.
Use only original Bosch HM /TC planer blades.
The carbide planer blade (HM/TC) has 2 cutting edges and can be reversed.
When both cutting edges are dull, the planer blade must be replaced. The HM /TC planer blade may not be resharpened.
Disassembling the Planer Blades (see figure C )
To reverse or replace the planer blade, rotate the blade head 22 until it is parallel to the planer shoe 11. Loosen the two fastening screws 24 with the
Allen key 25 by approx. 1 2 turns. If necessary, loosen the blade-clamping ele-
ment 23 by giving it a light blow with a suitable tool (e. g. a wooden wedge). Push the planer blade 26 sidewards out of the blade head with a piece of wood.
Assembling the Planer Blades (see figure D )
The guide groove of the planer blade always ensures continuous height adjustment when replacing or reversing it.
Clean the blade seat (clamping element) and the planer blade respectively, if required.
When assembling the planer blade, ensure that it is seated properly in the blade holder of the clamping element 23.
The planing blade must be assembled and aligned centrally to the planer shoe.
Afterwards tighten the fastening screws 24 again.
Before restarting, check if the clamping screws 24 are tightened well.
Rotate the blade head 22 by hand and ensure that the planer blade does not run into the planer shoe or housing.
Replacing the Drive Belt
Before any work on the machine itself, pull the mains plug.
Loosen screw 10 and take off the belt cover 9. Remove worn drive belt 28. (see figure E )
Before assembling a new drive belt, clean both belt pulleys 27 and 29. Place the new drive belt on the small belt pulley 29 first and then work it on the large belt pulley 27 by hand while rotating. (see figure F )
Take care that the drive belt runs exactly in the length grooves of the drive gear and the pulley.
Reattach the belt cover 9 and tighten with the screw 10.
Maintenance and Cleaning
Before any work on the machine itself, pull the mains plug.
For safe and proper working, always keep the machine and the ventilation slots clean.
Clean the blade protector 21 regularly and ensure that it runs free.
When the carbon brushes are worn out, the machine switches itself off. The machine must be sent to customer service for maintenance (for address, see the “Service and Customer Assistance” section).
If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools.
In all correspondence and spare parts orders, please always include the 10-digit order number given on the nameplate of the machine.
WARNING! Important instructions for connecting a new 3-pin plug to the 2 wire cable.
The wires in the cable are coloured according to the following code:
strain relief
live = brown neutral = blue
To be fitted by qualified professional only
Do not connect the blue or brown wire to the earth terminal of the plug.
Important: If for any reason the moulded plug is removed from the cable of this machine it must be disposed of safely.
14 · 2 609 140 180 · TMS · 08.03.02
English – 4
Downloaded from www.Manualslib.com manuals search engine
EURO · BA 2 609 140 180 · GHO 26-82 · GB · OSW 02/04 2 609 140 180.book Seite 5 Mittwoch, 3. April 2002 9:19 09
Environmental Protection
Recycle raw materials instead of disposing as waste The machine, accessories and packaging should be sorted for environmental-friendly recycling. These instructions are printed on recycled paper manufactured without chlorine. The plastic components are labelled for categorized recycling.
Noise/Vibration Information
Measured values determined according to EN 50 144. Typically the A-weighted sound pressure level of the product is 84 dB (A). The noise level when working can exceed 85 dB (A). Wear hearing protection! The typical hand/arm vibration is below 2.5 m/s2.
Service and Customer Assistance
Great Britain
Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park North Orbital Road Denham-Uxbridge GB-Middlesex UB 9 5HJ
Service………………………. +44 (0) 18 95 / 83 87 82 Advice line ……………….. +44 (0) 18 95 / 83 87 91
Fax ……………………………………… +44 (0) 18 95 / 83 87 89
Ireland
Beaver Distribution Ltd. Greenhills Road IRL-Tallaght-Dublin 24
Service…………………………….. +353 (0)1 / 414 9400
Fax ……………………………………………. +353 (0)1 / 459 8030
Australia
Robert Bosch Australia L.t.d. RBAU / SPT2 1555 Centre Road P.O. Box 66 Clayton AUS-3168 Clayton/Victoria
……………………………………….. +61 (0)1 / 800 804 777
Fax ……………………………………….. +61 (0)1 / 800 819 520
www.bosch.com.au E-Mail: [email protected]
New Zealand
Robert Bosch Limited 14-16 Constellation Drive Mairangi Bay Auckland New Zealand
…………………………………………….. +64 (0)9 / 47 86 158
Fax …………………………………………….. +64 (0)9 / 47 82 914
Declaration of Conformity
We declare under our sole responsibility that this product is in conformity with the following standards or standardization documents: EN 50 144 according to the provisions of the directives 89/336/EEC, 98/37/EC.
Dr. Gerhard Felten
Dr. Eckerhard Strötgen
15 · 2 609 140 180 · TMS · 08.03.02
Robert Bosch GmbH, Geschäftsbereich Elektrowerkzeuge Subject to change without notice
English – 5
Downloaded from www.Manualslib.com manuals search engine
