Synco P1 Series Microphone User Manual (+ PDF)

TX Transmitter
- Power Key
- Working Indicator
- Built-in Microphone
- Contacts
- Back Clip
RX Receiver
- Volume Button
- Type-C Port
- Working Indicator
- Connector
- Contacts
- Lightning Connector
- Type-C Connector
Wireless Charging Case
- Pairing Key / Power Indicator Key
- Type-C port
- Working Indicator
- Contacts
Indicator *

Note: The indicator identification is shown as follows.

	Transmitter		Receiver
Working Indicators (White Light)	On	Flash	On
Working Indicators (Red Light)	On	Flash	Single indicator keeps on (In the case)

Note: The transmitter will shut down automatically if it
unpaired or disconnected for 5 minutes.

Operations

1. Basic operations

Tap the drawer to the right of the charging box and take out the
transmitter and receiver.

2. Turn it on/off

Transmitter: The transmitter(s) automatically
turn(s) on after being taken out, and automatically shut down when
put back into the charging box; (Force switch on and off: long
press the power button of the transmitter for 3 seconds)
Receiver: Insert the mobile phone device to
switch on automatically, and the indicator flashes. *Note: You can
check whether the mobile phone OTG is on when he receiver indicator
is not on after being inserted to the mobile phone.

3. Charge

Transmitter: Connect the contact of
transmitter to the charging box when put the transmitter back into
the charging box.
Charging case: Connect the charging box to the
power supply through the charging cable, and the charging box water
lamp circulates during charging. Short press the power indicator
button, the number of indicator lights shows the power
condition.
Charging Mobile phone: Insert your phone’s
charging cable into the Type-C port of the receiver when in use,
and the charging current is adjusted according to the phone’s
battery max up to 800mA *Note: The receiver does not need to be
charged and can be used directly when plugged in the phone.

4. Pairing

Pairing in the charging box:

Place the transmitter and receiver in the charging box, and
connect the contact with the contact of the charging box;
Open the charging box, press and hold the matching button on
the box for 3 seconds;
The indicator lights of the transmitter and receiver cycle, and
the pairing is successful.

View Fullscreen

Microphone P1 Series
User Manual
Thank you for choosing SYNCO product. Please read this manual carefully before use and follow all instructions mentioned herein.

Caring For Your SYNCO Product
· Please keep the product in a dry, clean, dust-free environment. · Keep corrosive chemicals, liquids and heat source away from the product to prevent mechanics damage. · Use only a soft and dry cloth for cleaning the product. · Malfunction may be caused by dropping, impact of external force. · Do not attempt to disassemble the product. Doing so voids warranty. · Please have the product checked or repaired by authorized technicians if any malfunctions happened. · Failure to follow all the instructions may result in mechanics damage. · Warranty does not apply to human errors.
Package List

Transmitter x1

Receiver (Type-C or Lightning Connector) x1

Wireless Charging Storage x1

Mic Windshield x1

Charging cable x1

Product Introduction
1. TX Transmitter
Power Key Working Indicator Built-in Microphone Contacts Back Clip

2. RX Receiver
Volume Button Type-C Port Working Indicator Connector Contacts

Lightning Connector Type-C Connector

3. Wireless Charging Case Pairing Key / Power Indicator Key Type-C port Working Indicator Contacts
4.Indicator * NoteThe indicator identification shown as follows.

Left

Right

Left

Right

Transmitter

Working Indicators (White Light) On Flash

Fast Flash

Pairing

Slow Flash

Unpaired

Illuminate sequentially

Paired, normal working

Single indicator keeps on Noise cancellation on

Working Indicators (Red Light) On Flash

Single indicator keeps on (In the case)

Charging, and turns off when fully charged

Receiver

Working Indicators (White Light) On Flash

Fast Flash

Pairing

Slow Flash

Unpaired

1~5 indicators on
Single indicator flashed slowly

Connected and working normally. The number of lights on indicates the current volume
Mute on

Wireless Charging Case

Working Indicators (White Light) On Flash

1~5 indicators on

The number of lights on indicates the current volume

Operations
1. Basic operations
Tap the drawer to the right of the charging box and take out the transmitter and receiver.

2. Turn it on/off
Transmitter: The transmitter(s) automatically turn(s) on after be taken out, and automatically shut down when be put back into the charging box; (Force switch on and off: long press the power button of the transmitter for 3 seconds) *Note: The transmitter will shut down automatically if it unpaired or disconnected for 5 minutes.
Receiver: Insert the mobile phone device to switch on automatically, and the indicator flashes. *Note: You can check whether the mobile phone OTG is on when he receiver indicator is not on after be inserted to the mobile phone.

3. Charge Transmitter: Connect the contact of transmitter to the charging box when put the transmitter back into the charging box.
Charging case: Connected the charging box to the power supply through the charging cable, and the charging box water lamp circulates during charging. Short press the power indicator button, the number of indicator lights shows the power condition.
Charging Mobile phone : Insert your phone’s charging cable into the Type-C port of the receiver when in use, and the charging current is adjusted according to the phone’s battery max up to 800mA *Note: The receiver does not need to be charged and can be used directly when plugged in the phone.

4. Paring Pairing in the charging box: Place the transmitter and receiver in the charging box, and connect the contact with the contact of the charging box; Open the charging box, press and hold the matching button on the box for 3 seconds; The indicator lights of the transmitter and receiver cycle, and the pairing is successful.
Pairing in use: The receiver has been inserted into the mobile phone and is switched on; Turn off the transmitter, press and hold for 8 seconds when it is turned off, and wait for five indicator lights to flash quickly to enter the frequency alignment state. The working indicator light of transmitter and receiver is broken, and the matching is successful.

5. Adjust the volume Click the receiver volume button to adjust the volume and the number of indicators shows the current volume level. Double click the volume button to enable or disable mute and single indicator keeps on when mute is on.
6. Noise reduction Click the power button of the transmitter to turn on the noise reduction, and single indicator keeps on. * Double click the power button of the transmitter to turn off/on the light effect.

Specifications

TX Transmitter

Wireless Transmission RF Frequency Band Frequency Response Working Distance
Sampling Rate Bit Depth Sensitivity SNR Battery Type Battery Charging Time Battery Life Dimensions Material Weight

Digital 2.4GHz 2400-2483.5MHz 20Hz-20KHz 492ft/150m(LOS area); 164ft/50m(NLOS area) 48KHz 16Bit -36dB 75dB Built-in Lithium Battery, 120mAh 1.5H 5H 49x19x19 (mm) ABS 10g

RX Receiver Wireless Transmission RF Frequency Band Working Distance
Sampling Rate Bit Depth Connector Power Input Dimensions Material Weight

Digital 2.4GHz 2400-2483.5MHz 492ft/150m(LOS area); 164ft/50m(NLOS area) 48KHz 16Bit Type-C or Lightning Output Type-C 49x30x9 (mm) ABS 5g

Wireless Charging Case

Battery Type Battery Charging Time Charging Port Power Requirements Dimensions Weight

Built-in Lithium Battery, 300mAh 1.5H Type-C Port 5V 2A 70x43x37 (mm) 58g

Warranty
Warranty Period
Thank you for purchasing SYNCO products.
1. Customers are entitled to free replacement or repair service in case of quality defect(s) found in the product under normal use within 30 days upon receipt of the product.
2. Original SYNCO products are entitled to 12-month limited warranty service. The warranty period begins on the date of purchase of brand new, unused products by the first end-user.

Within the warranty period, if product defect or failure is attributable to material defection or technological problem, the defective product or defective part will be repaired or replaced without charge (service and materials fee).
Warranty Exclusions and Limitations
Faults resulted from inappropriate use of a product without following its operation specification 1. Artificial damage, e.g. crash, squeeze, scratch, or soaking 2. Modifications to a product by its user or a third party without prior written consent of SYNCO, e.g. replacement of element or circuit, label alteration 3. The code on product is inconsistent with that of warranty certificate, or the code on the product or warranty certificate is altered or torn off 4. All consumable accessory attached to a product, like cable, wind muff, battery 5. Faults as a result of force majeure, such as fire, flood, lightning, etc.
Warranty Claim Procedure
1. If failure or any problem occurs to your product after purchase, please contact a local agent for assistance, or you can always contact SYNCO’s customer service through email at [email protected]. 2. Please retain your sales receipt and warranty certificate as proof of purchase. If any of these documents is missing, only sales return or chargeable service will be provided. 3. If the SYNCO product is out of the warranty coverage, the service and the parts cost will be charged.

WARRANTY CERTIFICATE
Product Model: Date of Purchase: Serial Number: Malfunction Description :
Buyer Name: Buyer Telephone : Buyer Mail : Buyer Address : Dealer : Dealer Telephone :
Delivery Date : Cause of Malfunction : Maintenance Personnel : Malfunction Processing :
*Please register your warranty. Meanwhile, you are welcomed to contact us via Email [email protected]
Guangzhou Zhiying Technology Co., Ltd Room 2401, 24 / F, South Tower, Lisheng Plaza, No. 68 Huadi Avenue, Liwan District, Guangzhou, China, 510000 [email protected] www.syncoaudio.cn