Skimmer Box Cover
Product Information
The Hide Skimmer Cover is a patented product designed to cover
the skimmer box in swimming pools. It is made up of a frame, lid,
and key, and is available in different kit sizes. The skimmer box
cover is protected by international and U.S. design patents.
The kit includes the following materials and tools:
- A Hide Safety Key: This key is used to safely open and close
the installed Hide cover. Single key models are available in kits
10, 20, and 30mm, while double key models are available in kits 40,
50, and 60mm. - D Edge Protector: This frame is inserted into a recess within
the landscaped area to protect the coping/surrounds from chipping
or breakage. - B Height Adjuster: This is a tray that holds the inlay material
and provides an extra 5mm (3/16) height if the inlay material is
not thick enough to achieve a flush finish with the top of the
Inlay Cover. It suits both single key and double key models. - E Adhesive: Hide Adhesive is used when assembling the Inlay
Cover. It needs to be inserted into a caulking gun for use. - F Info Pack for the Homeowner: This pack includes the
Homeowners Manual and Warranty information, which should be passed
on to the homeowner after installation.
Additional equipment needed for installation includes a circular
saw, angle grinder, personal protective equipment (PPE), level work
surface, tape measure and marker, sponge and water, caulking gun,
general purpose bucket, mortar, mortar bed mix, grout, grout and
spacers, trowel, and expansion joint gap filler.
Depending on the installation location, the Hide product may
need to be installed with different types of landscaping materials
or grout lines. It can be installed to be virtually invisible with
extra care.
Product Usage Instructions
1. Assembling the Inlay Cover
- Cut the tile or stone inlay to the desired size.
- Mark up and cut a keyway at the center of the inlay material,
with a width of 6mm (1/4). - Clean and dry the inlay material. If using tumbled or chiselled
edge tile/stone, cut all four edges for a better finish. - Position the keyway on the tile edge closest to the pool.
Ensure that the key fits the keyway before gluing. Note: Two-key
models require two keyways.
2. Fitting Tile/Stone Inlay
Note: Failure to complete these steps may result in a weak
adhesive bond. Ensure that bonding materials are fully dry before
bonding, especially in cold weather.
- Calculate the amount of adhesive required by measuring the
height difference between the Inlay Cover and the inlay material
thickness. - If the height difference is under 3mm (1/8), proceed to the
next step.
FOR THE
CONTRACTOR
INSTALLATION INSTRUCTIONS HIDE SKIMMER COVER
International Patent Protection: The skimmer box cover – frame, lid and key product contained herein is covered by International Application PCT/AU2018/000149 1
The skimmer box cover – frame and lid product contained herein is covered by U.S. Design Patent Application No. 29/663,823
MATERIALS + TOOLS
IN THE KIT
A HIDE SAFETY KEY
DO NOT LEAVE IN THE COVER! Pass to the Homeowner. Enables the installed HIDE cover to be safely opened/closed.
Kits 10, 20 & 30mm are single key models. Kits 40, 50 & 60mm are double key models.
D EDGE PROTECTOR
A frame inserted into a recess within the landscaped area. It protects the coping/ surrounds from chipping/ breakage.
B HEIGHT ADJUSTER
C INLAY COVER
A tray which holds the inlay material
Provides 5mm (3/16″) extra
e.g. tile, paver, decking, cement.
height if inlay material is
not thick enough to achieve
a flush finish with the top of the Inlay Cover.
or
Suits both single key and double key models.
Single Key model or double key model
HIDE
E ADHESIVE
HIDE Adhesive to be inserted into a caulking gun. For use when assembling the Inlay Cover.
ADHESIVE
F INFO PACK
FOR THE
HOME OWNER
PLEASE PASS TO THE HOME OWNER
Homeowners Manual and Warranty pack. To be passed on after installation.
EQUIPMENT YOU’LL NEED
(The type of inlay materials to be fitted will determine the tools required.)
CIRCULAR SAW
ANGLE GRINDER
For cutting a keyway in the inlay material.
PERSONAL PROTECTIVE EQUIPMENT (PPE)
LEVEL WORK SURFACE
TAPE MEASURE + MARKER
SPONGE + WATER
CAULKING GUN
GENERAL PURPOSE BUCKET
MORTAR
MORTAR BED MIX
GROUT
GROUT & SPACERS
For installing the Edge
If grouting tiled/stone inlay.
Protector.
2
TROWEL
EXPANSION JOINT GAP FILLER.
INLAY SOLUTIONS
Depending on where the HIDE product is to be installed, it may run across two different types of landscaping materials. Similarly, it may need to be inserted where grout lines are present, or fitted with an intricate tile pattern.
With a little extra care, the HIDE product can be installed so it is virtually invisible.
1 GROUT MATCHED
2 TILE BANDING
3 INTRICATE PATTERNS
4 TIMBER DECKING
3
ASSEMBLING THE INLAY COVER FITTING TILE/STONE INLAY
NOTE NUMBER OF KEYWAYS REQUIRED: 10, 20 & 30mm (0.4″, 0.8″, & 1.2″) lids require one keyway cut and 40, 50 & 60mm
1 CUT TILE (INLAY) TO SIZE
2 MARK UP & CUT
KEYWAY AT
6mm (1/4″)
CENTER
3 CLEAN & DRY
25mm (1″)
If using tumbled/chiselled edge tile/stone cut all 4 edges for a better finish. See previous page to view options for aligning inlay and grout lines to coping/surrounds.
Ensure keyway is positioned on the tile edge which will be closest to the pool. Check that the key fits the keyway before gluing.
NOTE: Two key models require two keyways.
Failure to complete these steps may result in a weak adhesive bond.
You must insure that bonding materials are fully dry before bonding especially in cold weather.
4 CALCULATE THE AMOUNT OF ADHESIVE
REQUIRED by measuring the height difference between
Inlay Cover and Inlay material thickness.
INLAY COVER
INLAY (TILE)
INTERNAL MINUS HEIGHT
HEIGHT
HEIGHT DIFFERENCE MM (INCH)
C
5 HEIGHT DIFFERENCE UNDER 3MM (1/8″)
1 – 2mm (1/16″) = Qty 5 x beads 5mm (3/16″) wide or 2 – 3mm (1/8″) = Qty 7 x beads 8mm (5/16″) wide
(For distances over 3mm see step 7)
C
E
ADHESIVE
HIDE
Avoid placing adhesive within 10mm (3/8″) of keyway and drainage holes. Ensure the adhesive supports each corner of the inlay material. Ensure all bonding materials are fully dry.
6 Flip Inlay Cover C over and press down onto inlay (tile):
So that both inlay cover and tile sit upside down flush on a flat surface
for 15 minutes to let adhesive stiffen. Curing time is longer in cold weather.
15
MINS
C CROSS SECTION VIEW: C
ADHESIVE
INLAY TILE
7 HEIGHT DIFFERENCE OVER 3MM: (1/8″)
USE THE HEIGHT ADJUSTER SUPPLIED
B
2mm Height Adjuster used allowing for two applications of Adhesive. (See step 8)
C CROSS SECTION VIEW: B
INLAY TILE
4
LEVEL WORK SURFACE
LEVEL WORK SURFACE
(1.6″, 2″, & 2.5″) lids require two keyways cut at opposite ends of the stone to suit inlay lid.
8 HEIGHT DIFFERENCE OVER 3MM: (1/8″)
To calculate TOTAL adhesive to use with the Height
Ensure the adhesive supports
Adjuster, remember there will be two lots of adhesive
each corner OF THE INLAY
applied ie. adhesive is applied inside the Inlay Cover (C)
MATERIAL above and below
AND the reverse side of the inlay material (tile).
the Height Adjuster.
9
Place Height Adjuster on inlay (tile), then flip Inlay Cover (C) over and press down
onto Height Adjuster (B):
C
B
?QTY x ?MM
C
Avoid placing adhesive within 10mm (3/8″) of keyway and drainage holes. Mark their position through the height adjuster with a cross.
10 PRESS DOWN FOR A LEVEL FINISH
CORRECT FINISH:
11 WAIT WHILE ADHESIVE STIFFENS
Curing time is longer in cold weather.
THEN FLIP RIGHT WAY UP
15 MINS
C
WRONG FINISH:
C
INLAY TILE
C
12 CENTER TILE IN THE COVER
CORRECT FINISH:
WRONG FINISH:
13
24
HOURS
LET ADHESIVE SET
Curing time is longer in cold weather.
INLAY TILE CENTRED
INLAY TILE NOT CENTRED
14 TO FIT DECKING BOARDS
Apply glue between timber and lid
allowing for sufficient clearance
for drainage.
C
C
For a seamless finish, pattern
Make sure the glue has stiffened and remains flush with the inlay cover.
match timber and grain through
Use tile spacers to center the infill.
the inlay cover.
5
INSTALLING THE EDGE PROTECTOR
15 POOL PREPARATION
NEW POOLS:
SET DEPTH – WHEN LAYING LEVELLING BED, PROVIDE SPACE FOR EDGE PROTECTOR SO IT WILL BE FLUSH WITH TOP OF INSTALLED TILE
EXISTING POOLS:
CUTOUT – MARK OUTLINE FOR CUTTING SURROUNDS AND CUT DEPTH TO MATCH SELECTED
EDGE PROTECTOR AND A MORTAR BED
D
D
Ensure edge protector is centred over skimmer to mark cutting area.
Allow for 1-2mm (1/16″) clearance on all sides.
16 INSTALL MORTAR
REMOVE DEBRIS FROM RECESS THEN FILL RECESS WITH A MORTAR BED
18 ALLOW MORTAR TO SET
D
MORTAR
17 PUSH IN EDGE PROTECTOR
D
Ensure edge protector sits level with surrounds. Remove excess mortar.
19 EDGE PROTECTOR
TOP VIEW OF INSTALL The Edge Protector may be left loose on its mortar bed or filled with an expansion joint gap filler.
6
IMPORTANT CONTRACTOR INFORMATION
EARTHING (BONDING) RULES AND REGULATIONS HIDE products are constructed from 316 marine grade stainless steel, and are considered a conductive material. Safety regulations vary and you should consult your local authority to determine what rules may apply in your area. Bonding is the responsibility of the installer, attachment points have been provided to allow for use of bonding devices if required. Check your local regulations to ensure the installation meets electrical safety requirements.
D
!!SAFETY FIRST!!
REMOVE KEY FROM COVER
PASS KEY TO HOMEOWNER
NEVER leave the HIDE Safety Key in the cover for any reason, especially after install.
Leaving the Safety Key in the top of an installed cover may be dangerous, as it enables children to access the Skimmer.
DO NOT RISK IT – HIDE recommends that once the cover is installed, the Safety Key is passed to the homeowner and is stored securely.
NO ACID / CHEMICAL WASH CONTACT
ACID and chemical washes will cause discolouration and/or rusting on the stainless steel HIDE components. Acid or chemical contact will void the HIDE warranty.
SAFE WORK PRACTICES
ALWAYS be conscious of your and co-workers’ safety while assembling and installing the HIDE components. Personal protective equipment (PPE) must be worn, especially when cutting tiles and using adhesive. Recommended PPE includes eye and ear protection, gloves, dust mask and safety boots.
7
ACCESS & INSPECTION
OTHER PRODUCTS DRAIN
CONCRETE WET POUR
The HIDE Access and Inspection Covers can be used for underground service points including: water table inspection pipe (typically close to the skimmer box); grey water inspections outlets (IO); water tanks; balance tanks; taps and irrigation; valves and meters.
The HIDE Drain Cover can be used in most outdoor areas, including patios, decks and pathways allowing for a water intake compatible with a standard 90mm or 100mm drainage network.
HIDE Drain Covers not only look amazing but provide superior safety and performance.
The HIDE Concrete Cover is filled and finished at the same time as the pool surrounds. This ensures this cover perfectly matches the selected surface finish in both texture and colour. If you are wanting to finish your pool surrounds in a material like polished or decorative concrete, this is the product for you!
International Patent Protection:
8
The skimmer box cover – lid and key product contained herein is covered by U.S. Patent Application. No. 15/336,801
The skimmer box cover – lid product contained herein is covered by U.S. Design Patent No. D819788
8PP-INSTAL-2019:01-V1
