A04965A 1-Light Matte Black and Polished Gold Drum
Product Information
- Item Number: A04965A
- Working Hours: Mon – Fri 9:00 – 16:00 EST
- Contact Number: +1 850 296 2377
- Email: [email protected]
Product Usage Instructions
- We suggest installation by a licensed electrician.
- Read the instruction carefully and save it for future
reference. - Before starting any work, always shut off the electricity.
- Ensure the mounting surface is clean, dry, flat, strong enough,
and 1/4 larger than the canopy on all sides. Correct any gaps
exceeding 3/16. - Check if the ceiling or wall can support the weight of the lamp
before installation. - Make sure to use a voltage of 120V. The maximum wattage for LED
bulbs is 20W. - Avoid contact with acidic and alkaline substances to prevent
damage to the lamp’s surface. - When replacing bulbs, turn off or unplug the lamp and wait
until it cools down. - Use common sense, caution, and care when handling electrical
products.
Tools Required
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
Parts Included
- (A) Mounting plate – 1
- (B) Green ground screw – 1
- (E) Stud – 2
- (F) Canopy – 1
- (G) Lock nut – 4
- (H) Steel Wire – 3
- (I) Cable – 1
- (J) Body assembly – 1
- (K) Crystal hook – 53
- (L) Crystal – 53
Accessories Included
- (C) Plastic wire connector – 3
- (D) Mounting screw – 2
- (K) Crystal hook (spare part) – 2
- (L) Crystal (spare part) – 2
Assembly & Installation Instructions
- Remove the fixture from the carton and check that all parts and
accessories are included. - Turn off the power before starting the installation.
- Remove the mounting plate (A) using the mounting screws
(D). - Connect the wires according to the provided wire connection
chart. Note that the ground wire is a bare copper wire and should
not be connected to other wires. - Connect the ground wires as indicated in the chart.
- Connect the black or red supply wire to the outlet box ground
using the green ground screw. - Connect the white supply wire to the fixture ground using the
dimples and cupped washer. - Follow the additional wiring instructions based on the type of
parallel cord being used.
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
Item Number: A04965A
WARNING (To reduce the risk of fire, electric shock, or personal injury): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation. 6. Make sure the voltage you are using is 120V. The maximum wattage is LED, 20W. 7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp. 8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
quickly. 9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It
must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED Before starting assembly and installation please prepare the needed (NOT INCLUDED): tools as below picture
Ladder
Philips Head or Flat Blade Screwdriver
Electrical Tape
Pliers
Wire Cutter/Stripper
Page: – 1 – / 4
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
PARTS TYPE & QTY INCLUDING: (A) Mounting plate (1) (B) Green ground screw (1) (E) Stud (2) (F) Canopy (1) (G) Lock nut (4) (H) Steel Wire (3) (I) Cable (1) (J) Body assembly (1) (K) Crystal hook (53) (L) Crystal (53)
ACCESSORIES & QTY ENCLOSED: (C) Plastic wire connector (3) (D) Mounting screw (2) (K) Crystal hook (2) (spare part) (L) Crystal (2) (spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
Page: – 2 – / 4
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
3 » Unscrew studs (E) from canopy (F).
Remove mounting plate (A).
4 » Attach mounting plate (A) to the outlet box with
mounting screws (D).
5 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
A
B
Connect wires according to the below chart
Connect Black or Red Supply Wire to:
Connect White Supply Wire to:
OUTLET BOX GROUND GREEN GROUND SCREW
OUTLET BOX GROUND
FIXTURE GROUND
DIMPLES
GREEN GROUND SCREW
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
FIXTURE GROUND
Clear, Brown, Gold or Black without tracer
Insulated wire(other than green) with copper conductor
Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with silver conductor
CUPPED WASHER
* Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Neutral Wire
· Twist wires together with plastic wire connectors until tightly joined. · Wrap each connector with approved electrical tape. · Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Page: – 3 – / 4
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
7» Raise canopy (F) to the ceiling and secure canopy
(F) in place by tightening studs (E) onto the preassembled screws in mounting plate (A).
8 » 1) Hang crystals (L) to holes of body assembly
(J) with crystal hooks (K) as shown in the illustration.
2) To adjust the hanging height of the fixture:
Press down and hold lock nuts (G) by hand. Pull or push steel wires (H) and cable (I) in and
out of canopy (F) to increase or decrease the hanging height. · Please adjust steel wires first.
9. Check everything is already installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Page: – 4 – / 4
