A04971W4 30-in 4 Light Matte Black Polished Gold
Product Information
The product is an electrical lamp with the item number A04971W4.
It operates on a voltage of 120V and has a maximum wattage of 60W
per bulb (Type A). The lamp should be installed by a licensed
electrician to reduce the risk of fire, electric shock, or personal
injury.
The mounting surface for the lamp should be clean, dry, flat,
strong enough, and 1/4 larger than the canopy on all sides. Any
gaps exceeding 3/16 between the mounting surface and canopy should
be corrected. The ceiling or wall where the lamp will be installed
must be able to support its weight.
It is important to keep the lamp away from acidic and alkaline
substances to avoid damaging its surface. When replacing bulbs, the
lamp should be turned off or unplugged, and the bulbs should be
replaced only when they have cooled down.
Product Usage Instructions
- Before starting assembly and installation, make sure you have
the following tools (not included):
- Ladder
- Philips Head or Flat Blade Screwdriver
- Electrical Tape
- Pliers
- Wire Cutter/Stripper
that all parts and accessories are included.
attempt any work without shutting off the electricity until the
work is done.
provided mounting screws (A).
chart. Note that the ground wire is a bare copper wire and should
never be connected to other wires.
or fixture ground, depending on the wire type.
smooth) and follow the instructions for connecting specific wire
colors.
Please refer to the user manual for any additional safety
instructions or information.
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
Item Number: A04971W4
WARNING (To reduce the risk of fire, electric shock, or personal injury): 1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time. 3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation. 6. Make sure the voltage you are using is 120V. The maximum wattage is Type A, Max 60W per bulb. 7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp. 8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot
quickly. 9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It
must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED Before starting assembly and installation please prepare the needed (NOT INCLUDED): tools as below picture
Ladder
Philips Head or Flat Blade Screwdriver
Electrical Tape
Pilers
Wire Cutter/Stripper
Page: – 1 – / 3
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
PARTS INCLUDING: (C) Mounting plate (1) (D) Green ground screw (1) (E) Back plate (1) (F) Stud (2) (G) Upper cover (4) (H) Thumbscrew (24) (I) Metal strip (12) (J) Ring (4) (K) Glass shade (4)
ACCESSORIES ENCLOSED: (A) Mounting screw (2)
(B) Plastic wire connector (3) (H) Screw (1) (Spare part)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
2. Turn off power Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
3. Make assembly
Page: – 2 – / 3
+1 850 296 2377 Working hours : Mon – Fri 9:00 – 16:00 EST
Step A1 » Unscrew studs (F) from back plate (E), then set them aside for later installation. Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (C).
Secure mounting plate (C) to the outlet box with mounting screws (A).
Step A3 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
A
B
Connect wires according to the below chart
Connect Black or Red Supply Wire to:
Connect White Supply Wire to:
OUTLET BOX GROUND GREEN GROUND SCREW
OUTLET BOX GROUND
FIXTURE GROUND
DIMPLES
GREEN GROUND SCREW
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
FIXTURE GROUND
Clear, Brown, Gold or Black without tracer
Insulated wire(other than green) with copper conductor
Clear, Brown, Gold or Black with tracer
Insulated wire(other than green) with silver conductor
CUPPED WASHER
* Note: When parallel wires (SPT I& SPT ll) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Neutral Wire
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (E) and mounting plate (C), then secure them with the previously
removed studs (F).
Step A5 » 1) Unscrew thumbscrews (H) from upper covers (G) and rings (J).
2) Pass thumbscrews (H) through the holes of metal strips (I), rings (J) and glass shades (K), then tighten thumbscrews (H) as shown in the illustration.
3) Pass thumbscrews (H) through the holes of metal strips (I) and upper covers (G), then tighten thumbscrews (H) as shown in the illustration.
4) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the socket.)
4. Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and non-abrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Page: – 3 – / 3
