Philco Pc900sle Range Hood User Manual

PC900SLE Range Hood

Product Information

Product Usage Instructions

1. Before connecting the hood, check that the supplied voltage and
   frequency match with that indicated on the appliance rating plate.
   If in doubt, ask for advice instore or from a qualified
   installer.
2. Use only the same size of fittings and mounting screws as
   recommended in the instruction manual. Failure to follow these
   instructions may result in electrical hazards.
3. Ensure proper ventilation of the room when the hood is in
   use.
4. Position the range hood at least 650mm above the cooking
   vessels on the hob.
5. Consult local regulations regarding extraction outlets and
   ensure compliance.
6. Do not connect the hood to a ventilation external timer or
   separate remote control system.
7. Drill holes for flue cover wall mounting brackets, rangehood
   mounting points, and anti-tilt fixing points using the base as the
   reference point.
8. Attach the chimney brackets and hood mounting screws. Use ST
   4x32mm screws and expansion plugs if attaching to masonry.
9. Remove the aluminum filters from the rangehood body and hang it
   on the mounting screws. Secure it at the anti-tilt locations.
10. Fix flexible duct if exhaust air needs to be directed
    outside.
11. Attach the chimney to the top bracket.
12. Connect the ducting adapter.

USER M A NUA L

PC 9 0 0 SLE

2

EN
Dear Customer Thank you for buying our range hood. Please read the user manual carefully and store in a handy place for later reference. This hood is designed for install on walls.
Read the following carefully to avoid damage or injury.
SAFETY AND WARNINGS
Where applicable, this appliance is supplied with fixings. Please ensure you use the correct fixings suitable for the substrate where the appliance will be installed and that they are able to support the weight of the appliance.
Before connecting the hood, check that the supplied voltage and frequency match with that indicated on the appliance rating plate. If in doubt, ask for advice instore or from a qualified installer.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similar qualified persons in order to avoid a safety hazard.
Use only the same size of fittings and mounting screws as recommended in this instruction manual. Failure to follow these instructions may result in electrical hazards.
Means for full disconnection must be incorporated in the fixed wiring in accordance with the local wiring installation rules for your country. An all-pole disconnection switch having a contact separation of at least 3mm in all poles should be connected during installation.
When the cookerhood is located above an appliance, the minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the hood shall be at least 650mm.
Consult local regulations regarding extraction outlets and ensure these are complied with. Do not connect the hood to a ventilation
3

or hot air duct containing combustion fumes from burning gas or other fuels. Confirm that room ventilation is appropriate with the local authorities. The air must not be discharged into a flue that is used for exhausting fumes from appliances burning gas or other fuels The hood may stop working during an electrostatic discharge (e.g. lightning). This involves no risk of damage. Switch off the electricity supply to the hood and reconnect after one minute. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. Do not install the appliance outdoors in a damp place or in an area which may be prone to water leaks such as under or near a sink unit. In the event of a water leak affecting the appliance, do not use and contact customer services to arrange for inspection. Do not use flammable sprays in close vicinity to the appliance. Please dispose of the packing material carefully. There is a fire risk if cleaning is not carried out in accordance with the instructions. Refer to the Care and Maintenance sections carefully for details on how to clean and replace the aluminium and carbon filters (if fitted). Refer to the Care and Maintenance section for details on the type of lamps that can be used and how to replace them. Do not use a steam cleaner for care and maintenance. The appliance is not intended to be operated by means of an
4

external timer or separate remote control system. There shall be adequate ventilation of the room when the hood is
used at the same time as appliances burning gas or other fuels. Ensure that the negative pressure of the installation site does not exceed 4 Pa (0.04 mbar) to ensure combustion fumes are not drawn back into the room. Do not use the hood if it shows signs of damage or imperfection. Contact customer services for assistance. Switch off the appliance at the mains supply before carrying out any maintenance work or cleaning. CAUTION: Accessible parts may become hot when used with cooking appliances. Do not flambé under the hood. To avoid the risk of fire, clean or replace the grease filter regularly and closely monitor pans containing hot oil. The manufacturer declines all liability for personal or material damage as a result of misuse or incorrect installation of this appliance. The appliance is for domestic use only as an extractor hood.
INSTALLATION INSTRUCTIONS
All installation must be carried out by a competent person or qualified technician. Before connecting the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate. The appliance must be connected directly to the mains using an omnipolar circuit breaker with a minimum opening of 3mm between the contacts. The installer must ensure that the correct electrical connection has been made and that it complies with the wiring diagram. Regularly check the power plug and power cord for damage. If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
WARNING: This is a Class II appliance and MUST NOT be earthed.
5

Contents of packaging

Rangehood (1)

Chimney (Upper+lower) (1)

Ø150mm Ducting adapter (1)
Upper chimney bracket (1)
Chimney bracket (1) 6

Reducer Ø150mm to Ø125mm adapter (1)
Expansion plug (8)
Screws (8) (ST 4x32mm)
Screws (4) (ST 4x12mm)

INSTALLATION

NN
top of cooking surface

Fixing dimensions

Positioning

290

320

538 Min 745/Max 1030

56
900 500
WARNING! these instructions may result in electrical hazards.
7

Drilling holes
Mark the location for flue cover wall mounting brackets, rangehood mounting points and anti-tilt fixing points above the rangehood using the base as the reference point (Fig. 1).

23.5 mm

250 mm

Upper chimney extension bracket attachment points

250 mm

Chimney bracket attachment points

559 mm 286 mm 36 mm

250 mm

Upper hood attachment points

Lower hood attachment points

Fig.1

580 mm

Attach chimney brackets and hood mounting screws
Attach the upper hood mounting screws in the locations shown in Fig.2. Use the ST 4×32 mm screws and expansion plugs if attaching to masonry.

8

2mm
Fig.2 Attached hood on wall Remove the aluminium filters from the rangehood body and hang
it on the mounting screws then secure at the anti-tilt locations as indicated in Fig. 3.
Fig.3
9

Connect ducting adapter Connect Ø150mm ducting adapter to the blower outlet and use
screws ST 4x12mm to fix it to the range hood (Fig. 4).
Ø150 to Ø125mm adapter Ø150mm Ducting adapter
Fig.4 If necessory, connect the Ø150 to Ø125mm adapter to the
Ø150mm ducting adapter (Fig. 4). Important! For best performance, Ø150mm ducting is recommended (Ø125mm ducting can be used, but will reduce the airflow of the cooker hood).
Fixing flexible duct If need exhaust air to the outside.
Connect Ø150 mm or Ø125 mm flexible duct to the adapter and fix it (Fig. 5).
Fig.5
10

Attach the chimney
Fig.6 Connect ducting adapter Fix the chimney to the top bracket
using two screws ST 4x12mm. Connect top of the ducting tube to vent kit as per manufacturers instructions (Fig. 7). Install back the aluminium filters to rangehood, and remove the protection film from rangehood and chimney.
Fig.7
11

OPERATING INSTRUCTIONS

Turn the hood on for a few minutes before you start cooking. The hood should be left on for a minimum of 5 minutes after cooking or
until all odours have dispersed.

Control panel features

1

2

3

4

5

1 ­ Filter clean warning display/button. Remind to replace the filter after the extractor fan working 50 hours. Press it to deactivate once the filter has been cleaned or replaced.
2 ­ Enable and disable extractor fan timer. The extractor fan works at current speed for 5 minutes and downs to the lower speed for 5 minutes until it stops.
3 ­ Lighting on and off. Keep pressed down to adjust the lighting intensity. 4 ­ On/Off button 5 ­ Fan speed ­ 1, 2 and 3.
Warning: the lighting should not be used as permanent light source but only for cooking.
CLEANING AND MAINTENANCE
Warning: always switch off the electricity supply before carrying out maintenance work on the hood. In the event of a fault, contact an official distributor or Customer Service. Exterior Cleaning : Use non-corrosive, liquid detergent and avoid the use of abrasive cleaning products.
Replacing the lamp
Ensure that the rangehood is unplugged, then slide out the retractable hood and remove the filters. Turn the lamp anti-clockwise to remove then replace the lamp by turning it clockwise. Note that lamps become hot when in use. Allow the lamps to cool down for a few minutes before changing them.
12

FUSE OFF

10′

from the manufacturer.
1 MONTH

65ºC
13

Replacing Activated charcoal filters Replace Activated charcoal every 3 months
3 MONTHS

Troubleshooting

Problem Excessive vibration.

Possible cause
The appliance is not installed properly on the brackets.

The fan blade is damaged.

The light is on, but the fan does not work.
Both the light and motor do not work.
Suction performance reduced.

The fan blade is jammed. The motor is damaged. Light bulb blown.
Power connection loose. Speed may be too low.
are dirty. Top vent might be obstructed. Optional vent kit might be twisted.

Solution Take down the appliance and check
Switch off the appliance. Repair to
personnel only.
Replace with a bulb of the correct rating. Check power supply. Select a higher speed.
Care and maintenance section). Clear any obstruction.
Ensure that the vent kit

Works normally but cooking smells linger.

manufacturer’s instructions.

The installation may not comply with The vent hose should be correct

the manufacturers instructions.

diameter throughout with no

reductions or restriction.(See

installation section).

recirculation mode or is full of grease.

maintenance section).

14

Recycling & disposal
The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.
15

16

f d°f

f

f

f d dd

f

d fd f

dd df

d fdf

df dd

3f

d 650 f
f ef

f

f

f

fddf

17

d d e ee f f° f d ee d fd f df df df f f ddf df ° f °f f f d f
df df df df d f df fdf df
f
18

19

(8) (ST 4x32mm)
(4) (ST 4x12mm) 20

21

ST 4×32 f
22

23

Ø

ST

Ø Ø
24

6
dST4x12 f f d f

25

(1d2 3)f df
d d
d
26

27

~f
3 ~

f

f f f f f
f f f

f

f
d f
f f f f °
f

f

f

f df

d

f

d f °

28

d f f d f dd df
29

30

31

Model No.: Serial No.: Dealer: Date of Purchase: Invoice No.:
The product specifications may be changed without prior notice. Please contact customer service for details if necessary.
If there is any inconsistency or ambiguity between the English version and the Chinese version,
the English version shall prevail.
Warranty Registration
Register your product online www.dchtoolbox.com
60815650.07.09.2022
DCH ToolBox Customer Service Centre
204 4/F, DCH Building, 20 Kai Cheung Road, Kowloon Bay, Hong Kong
Customer Service Hotline: (852) 8210 8210 E-mail: [email protected] Website: www.gilman-group.com

References

• Group Publishing
• DCH Toolbox
• Homepage | Gilman Group