NAC3MX-W-TOP Cable Connector
Product Information:
The powerCON TRUE1 TOP is a connector used for power
applications. It is designed for appliances that require both power
input and output connections. The connector has various models with
different specifications. It meets the approval standards of VDE EN
60320-1, UL 60320-1, and CAN/CSA-C22.2 No. 60320-1. The rating of
the connector depends on the cable type and diameter.
Connector Models:
- APPLIANCE INLET: NAC3MPX-TOP, NAC3MPX-WOT-TOP
- Power IN
- APPLIANCE OUTLET: NAC3FPX-TOP, NAC3FPX-WOT-TOP,
NAC3FPX-ST-TOP - Power OUT
- Combination Inlet/Outlet: NAC3PX-TOP
- Power IN/OUT
- Connector: NAC3FX-W-TOP
- Plug Connector: NAC3MX-W-TOP
Approval Standards:
- VDE EN 60320-1
- UL 60320-1
- CAN/CSA-C22.2 No. 60320-1
Rating:
Cable Type: H05VV-F3G, H07RN-F3G, SJTOW, SJOOW
Cable O.D.: 1.0 mm2 to 2.5 mm2 (H05VV-F3G), 1.5 mm2 (H07RN-F3G),
3 x 12 AWG (SJTOW, SJOOW)
Product Usage Instructions:
- Insert the cable into the bushing and housing. Apply cable
pulling lubricant to the cable jacket. - Separate the housing from the bushing while leaving the cable
in the bushing. - Place the chuck over the cable.
- Prepare the cable as shown in the instructions.
- Insert the wires into the terminals and fasten the screw with
Torx size T8. Apply a torque value of 0.7 Nm. - Push and turn simultaneously to slide the chuck and insert
together into the housing. Align the chuck and insert by
positioning the nose into the keyway. - Apply a torque value of 2.0 Nm to secure the connection.
- To disassemble, open the twist lock on the bushing. Slide the
bushing up the cable and tighten it with the provided tool. Use a
wrench size of 13 mm. Ensure the black O-ring is hidden to achieve
IP protection.
Safety Information:
- Do not expose the connection to bending forces or attach loads
to the cable. - Replace the connector if any parts are broken or excessively
worn for safety and certification reasons.
For more details and information about powerCON TRUE1 TOP, visit
www.neutrik.com.
R
APPLICATION & ASSEMBLY INSTRUCTION NAC3MX-W-TOP | powerCON® TRUE1® TOP
A APPLICATION INSTRUCTION
Application other equipment:
· The powerCON® TRUE1® system is certified as a connector with breaking capacity according IEC 60320, VDE 0625.
· It is intended for use as an appliance coupler and interconnection coupler. · It serves to supply power to an appliance and from an appliance to other equipment. · To be installed by qualified person only.
CONNECTOR ASSIGNMENT:
APPLIANCE INLET
NAC3MPX-TOP NAC3MPX-WOT-TOP
Power IN
APPLIANCE OUTLET
NAC3FPX-TOP NAC3FPX-WOT-TOP NAC3FPX-ST-TOP Power OUT
APPLIANCE INLET / OUTLET u Combination NAC3PX-TOP
Power IN
Power OUT
NAC3FX-W-TOP (Connector)
NAC3MX-W-TOP (Plug connector)
NAC3FX-W-TOP (Connector)
NAC3MX-W-TOP (Plug connector)
powerCON® TRUE1® TOP line is full backward compatible with the preceding powerCON TRUE1 products.
Approval based:
VDE EN 60320-1
UL 60320-1 CAN/CSA-C22.2 No. 60320-1
Rating: Cable Type: Cable O.D.:
250 V ac / 16 A H05VV-F3G 1.0 mm2, Length max. 2 m H05VV-F3G 1.5 – 2.5 mm2 H07RN-F3G 1.5 mm2 6.0 – 12.0 mm
250 V ac / 20 A SJTOW, SJOOW 3 x 12 AWG 6.0 – 12.0 mm
The manufacturer of cord sets and of interconnection cord sets is responsible for the conformity assessment according to the applicable regulatory documents.
B ASSEMBLY INFORMATION
A Insert cable into the bushing and housing.
Note: “Apply cable pulling lubricant to cable jacket.”
40 – 50 mm
NAC3MX-W 12650
22050
P S JET E
i
22500
B Separate the housing from the bushing (cable remain in bushing)
C
NAC3MX-W 12650 22050 22500
P S JET E
C Place chuck over the cable.
D Prepare cable as shown.
20 mm
[0.787″]
8 mm
[0.32″]
i Recommendation: Wire Pulling Lubricant – LUB-I/0.95
from 3MTM
20 mm
[0.787″]
8 mm
[0.32″]
VDE EN 60320-1
PE 23 mm [0.9″]
PE 23 mm [0.9″] UL 60320-1 CAN/CSA-C22.2 No. 60320-1
BDA 542
Page 1
R ASSEMBLY INSTRUCTION I powerCON® TRUE1® TOP – NAC3MX-W-TOP
E
Torx size T8
Insert the wires into the terminals and fasten the screw with Torx size T8.
Torque Value 0.7 Nm
Wiring
VDE
UL
L Þ
brown
black
N Þ
blue
white
Þ
green / yellow
green
Important: Align rubber key and latch.
NAC3MX-W 12650
22050
P S JET E
2.
22500
F
1. Important: Push and turn simultaneously.
3.
Slide the chuck onto the insert (1) and then both together into housing (2). Important: Align the chuck and insert by positioning the nose into the keyway.
5.
Torque Value 2.0 Nm
G
PRESS FIRMLY
NAC3MX-W 12650
22050
P S JET E
6.
22500
4.
Wrench size 13 mm
C FOR DISASSEMBLY OPEN TWIST LOCK!
1. Press with screw driver to unlock 2. Turn bushing 360°. 3. Repat step 1 + 2 until bushing is unscrewed.
1. 2.
Slide the bushing up the cable and tighten it with the tool as shown. Important: Black O-ring to hide to achieve IP protection (6).
(Tool available: Art. No. HTAC)
Find more details of powerCON TRUE1 TOP on www.neutrik.com.
D SAFETY INFORMATION
NAC3FXP -SW JET E
22050 LIECHTENSTEIN
FORCE
CAUTION
To ensure protection category, do not expose the connection to bending forces (e.g. do not attach loads to the cable, no free-dangling cable windings etc.).
SAFETY WARNING
For safety and certification reasons the connector must be replaced in case of any broken parts or excessive wear and tear.
Draft. Nr.: BDA 542 V4 Update: 2023-06-28
Neutrik AG I LI-9494 Schaan www.neutrik.com
Data subject to change without prior notice. © 2023 NEUTRIK®. NEUTRIK®, powerCON are registered trademark of Neutrik AG. ALL RIGHTS RESERVED.
Page 2
A brand of the Neutrik Group
Homepage - Neutrik
