Nilight B08QN51JZQ Light Pods Waterproof
Specifications
- VEHICLE SERVICE TYPE: Golf Cart, ATV, Motorcycle, Van, SUV, UTV, Snowmobile, Pickup Truck, Tractor
- VOLTAGE: 32 Volts
- LIGHT SOURCE: Type LED
- POSITION: Inside
- COVER INCLUDED: 6PCS LED Rock Light
- FIT TYPE: Universal Fit
- ITEM WEIGHT: 1 Pounds
- MATERIAL ALUMINUM: Rubber
- WATER RESISTANCE LEVEL: Waterproof
- REMOTE CONTROL INCLUDED: No
- NUMBER OF PIECES: 6
- VEHICLE SERVICE TYPE: Golf Cart, ATV, Motorcycle, Van, SUV, UTV, Snowmobile, Pickup Truck, Tractor
- WORKING VOLTAGE: 10-32V DC
- THEORETICAL LED POWER: 9W per light
- WIRE GAUGE: 22AWG; Wire length: 14”
- WATERPROOF: IP67
- MATERIAL: Die-cast aluminum, PC lens.
- LIFETIME: 50,000 hours
- BRAND: Nilight
Introduction
Blue LED Rock Light Pods from Nilight, 6 PCS Single LED rock light pods that may be used in a variety of places and for multiple purposes. Work well for underbody lights, wheel well lights, back-up and reverse lights, truck beds, off-road lights, machinery lights, construction lights, forklift lights, boat deck lights, and other lighting fixtures. Applications include forklift loading and unloading, golf carts, ATVs, UTVs, SUVs, motorcycles, boat decks, and trucks and tractors.
What’s in the box?
- 6PCS LED Rock Light
- 6 x led rock light pods
- 6 x rubber pad
- 6 x hardware pack
- User Manual
Universally suitable, working voltage 10-32V DC
Any vehicle or position can use an external light with a working voltage of 10-32V DC. Car underflow lights, wheel well lights, reverse/backup lights, truck bed lights, off-road lights, machinery lights, construction lights, forklift lights, and boat lights are a few examples of exterior lighting fixtures that can be used on any type of vehicle or location. For example, vehicle underflow lights, wheel well lights, back-up and reverse lights, truck bed lights, off-road lights, machinery lights, construction lights, forklift lights, boat lights, etc.
Build to last and be stylish
Single LED rock light pods that may be used in numerous positions and for multiple purposes. Work well for underbody lights, wheel well lights, back-up and reverse lights, truck beds, off-road lights, machinery lights, construction lights, forklift lights, boat deck lights, and other lighting applications.
Outstanding Heat Dissipation
The entire housing is made of die-cast aluminums, including the rear. improves heat dissipation, reduces potential dead light, and lengthens lifespan.
Waterproof to IP67
The exterior light is totally sealed, while the interior is sealed with two silicon rings. Be prepared for any weather conditions as the lights are IP67 weatherproof.
Note
Products with electrical plugs are made with American consumers in mind. Because outlets and voltage vary from country to country, this product might need an adapter or converter to be used where you are traveling. Before buying, kindly verify compatibility.
Frequently Asked Questions
You will need to have a roll of wire and connectors or be ready to solder and heat shrink tube the kit is lights and bolts.
1600 and completely waterproof snow mud and whatever else I run through proof. Very bright. I have12 on my truck.
You have to make your own.
Make a daisy chain. Red to red and blk to blk all the way around and back to toggle.
No, these lights do not come with a remote. You will need to have them wired into a switch to turn them on and off.
Bruh there is no harness. You make it as you go just remember to ground your light close to where it is mounted. Every light gets grounders mount point. Once you hook up one just daisy chain your power to the next location same with ground. I have 24 green lights on my daily driver.
You bet use some dog chain that should do it.
Yes
I couldn’t get the light to sit flush enough because of the wire, so I wound up using the rubber pad. I just zip tied the rubber to the light (put the ties in each hole) and didn’t use the screws either. Hope that makes sense!
68
Simple install. Get toggle switch and mount it where ever. Toggle should have 4 prongs/2 for power in and/2 for power out. Run a wire from positive side of batt to the power in prong. Find a good solid body ground and run that wire to ground in prong on switch. Now run wire (+) to light double splice for the first light and move on double splice each light till you get to last one. The ground is easy. You can either do it the way you did power or don’t run to each light. Take the ground from each and add just enough wire to ground each light to a solid location. I myself grounded each light separately so if I lose ground I only lose 1 light not all.
Could these lights be wired to ignition switch instead of a toggle switch? Do they need a relay?
You will need a relay my friend.
Daisy chain the lights grounding at each location.
I used silicon wire that I had left over from a job I did. Nothing major is needed. Make sure each light has its own ground and your good. I ordered a switch from Amazon that lights up green when my lights are on. Simple installation.
