Silverstone Sst-ex350-bf Extreme 350 Bronze User Manual (+ PDF)

Contents hide

SST-EX350-BF Extreme 350 Bronze

Product Information

The Extreme Series Extreme 350/450/500 Bronze is a power supply
designed for industrial grade systems. It comes in three variants:
350W, 450W, and 500W, all of which have an 80 Plus Bronze
certification. The power supply supports the standard SFX form
factor and provides a continuous power output at operating
temperatures up to 40 degrees Celsius. It features a silent running
92mm fan with a minimum noise level of 18dBA and utilizes
high-quality Japanese primary capacitors. The power supply has a
single +12V rail, PCIe 8pin and PCIe 6pin connectors, and is
equipped with Active Power Factor Correction.

Specifications:

SFX Form Factor
Models: SST-EX350-BF, SST-EX450-BF, SST-EX500-B
Power Output: 350W, 450W, 500W
Switching Power Supply With Active PFC
80 PLUS Bronze Certification

Product Usage Instructions

Ensure that the power supply is properly installed in your
system according to the SFX form factor.
Connect the AC input to a power source within the voltage and
frequency ranges specified in Table 1.
Connect the DC outputs to the appropriate components in your
system, ensuring that the voltages remain within the regulation
ranges specified in Table 2.
Distribute the load across the DC output rails according to the
typical load distribution shown in Table 3.
To maximize efficiency, aim to achieve the specified load
percentages mentioned in Table 4.
Monitor the temperature and operating conditions of the power
supply to ensure it remains within the specified limits.

Please refer to the complete user manual for more detailed
instructions and safety precautions.

View Fullscreen

Extreme Series Extreme 350/450/500 Bronze
80 Plus Bronze 350W/450W/500W SFX power supply
Support standard SFX form factor 24/7 continuous power output with 40 operating temperature
Silent running 92 mm fan with 18dBA minimum Japanese primary capacitor
High efficiency with 80 PLUS Bronze certification Class-leading single +12V rail
PCIe 8pin and PCIe 6pin connectors support

SPECIFICATION
SFX Form Factor
SST-EX350-BF
SST-EX450-BF
SST-EX500-B
350W 450W 500W Switching Power Supply With Active PFC 80 PLUS Bronze

1. Scope
This document defines the industrial quality, SFX 12V size, 350W, 450W, 500W, 5 output power supplies for the application of industrial grade system.

The SFX 12V series of power supplies meet the buss structures of Intel platform, and the following key features: 1)Input: Full Range (90-264Vrms) with Active Power Factor Correction. 2)Output: Product is provided with a total of five outputs to meet the requirement
of SFX 12V platform. 3)Cooling: A 92mm high reliable DC fan is used for cooling the power supply.
2. Electrical
The electrical specifications that follow are to be met over the environmental ranges specified in Section 3 unless otherwise noted.
2.1.AC Input
Table 1. lists AC input voltage and frequency range for continuous operation. The power supply is capable of supplying full-rated output power over the input voltage ranges specified.

Parameter Vin Voltage / 350W/450W
Vin Voltage / 500W Vin Frequency
Vin Current /350W Vin Current /450W Vin Current /500W Power Factor(PF)

Min

Nominal

Max

Unit

100-240

264

Vrms

103

115-230

254

Vrms

50/60

5.0

7.0

8.0

> 0.90

at 115Vac230Vac input and full load

Table 1. AC input

·The inrush current is less than 100A under the conditions of 240Vrms input and 25 ambient cold start. The inrush current is limited to the extent that no damage will be done to the power supply under any specified line, load, and temperature conditions. The inrush current will not cause external protection devices (fuses) to trip.
·The leakage current of the power supply module is less than 3.5mA measured at 240Vac input.
·The repetitive ON/OFF cycling of AC input voltage will not damage the power supply. ·The power supply can automatically recover from AC power loss. ·The primary fuse is installed for input over-current protection, and meet product safety
requirement.

2.2.DC Output
2.2.1. DC Output Voltage Regulations
The DC output voltages remain within the regulation ranges shown in Table 2. when measured at the load end of the output connectors under all AC line, O/P loads, and environmental conditions. The voltage regulation will be maintained under continuous operation for a period of time equal to the MTBF specified in section 5.2 at any steady state temperature and operating conditions specified in section 3.

+12V

+5V

+3.3V

-12V

+5Vsb

Unit

Range

±5%

±10%

±5%

Volt

Min

+11.40

+4.75

+3.165

-10.80

+4.75

Volt

Nom

+12.00

+5.00

+3.30

-12.00

+5.00

Volt

Max

+12.60

+5.25

+3.465

-13.20

+5.25

Volt

Table 2. DC Output Voltage Regulations

·The remote sense is provided to +12V, +5V, and +3.3V outputs to compensate for excessive cable drops.
2.2.2. DC Output Load Distributions The Table 3. defines the power supply typical output load distribution.

Output Output Minimum

350W

450W

500W

Rail Voltage Current (A)

Max. (A)

+12V

0.0

29.16

37.5

41.66

+5V

0.0

18.0

20.0

+3.3V

0.0

18.0

20.0

-12V

0.0

0.3

+5Vsb

0.0

2.5

Max. combined O/P of V2 & V3

110W

120W

Table 3. DC Output Load Distribution (350W 500W)

2.2.3. DC Output Efficiency

The power supply efficiency is 82% minimum measured at 20% & 100%, efficiency is 85% minimum measured at 50%, which is 115Vrms conditions. The efficiency is measured in accordance with the definition released by the 80 Plus Organization (Plug Load Solutions). shown in Table 4.

MEET 80 Plus Bronze

LOAD

3.3V

+12V

-12V

+5VSB

SPEC

20%

1.94A

4.27A

0.04A

0.44A

82%

350W

50%

4.85A

10.66A

0.11A

1.10A

85%

100%

9.69A

21.33A

0.22A

2.19A

82%

20%

2.21A

5.73A

0.05A

0.46A

82%

450W

50%

5.53A

14.33A

0.11A

1.15A

85%

100%

11.05A

28.67A

0.23A

2.29A

82%

20%

2.26A

6.52A

0.05A

0.47A

82%

500W

50%

5.66A

16.31A

0.12A

1.17A

85%

100%

11.32A

32.62A

0.23A

2.35A

82%

Table 4. MEET 80 Plus Bronze

2.2.4. DC Output Ripple & Noise

The output ripple & noise specifications listed in Table 6. will be met throughout the load ranges as specified in section 2.2.2 and the nominal line input voltage conditions as specified in section 2.1. Ripple & noise is defined as periodic of random signals over a frequency band of 10Hz to 20MHz. Measurements should be made with an oscilloscope with 20MHz bandwidth. Add a 10uF electrolytic capacitor and a 0.1uF ceramic capacitor across output terminal during ripple & noise measurement.

+12V

+5V

+3.3V

-12V

Max Ripple & Noise

120

Table 6. DC Output Ripple & Noise

2.2.5. DC Output Transient Response

+5Vsb 50

Unit mV P-P

The output voltages will remain within the regulation limits +-10%. The load-changing repetition rate is 50Hz to 10KHz, and the transient load slew rate 0.5A/us. The maximum step load size, and output capacitive loading are specified as followings in Table 7.

Step Load Size Capacitive Load

+12V 60% of Max Load 10000

+5V

+3.3V

30% of Max Load

10000

Table 7. DC Output Transient Response

-12V 0.1A 330

+5Vsb 0.5A 1000
03

2.2.6. DC Output Voltage Hold-up Time
The power supply will maintain outputs in regulation per section 2.2.1 despite a loss of input power at the nominal range of AC input and at 75% of maximum continuous output load as applicable for a minimum of 10 msec.
2.3. Timing / Housekeeping / control

Figure 1. Power Supply Timing Notes: T1 is defined is section 2.3.4
T2 is defined in section 2.3.5 T3, T4, T5 and T6 are defined in Table 8.

2.3.1. PWR_OK (Power Good Signal)

PWR_OK is a “power good” signal. It will be asserted high by the power supply to indicate that the +5V output is above the under voltage threshold listed in Table 2 of Section 2.2. PWR_OK will be de-asserted to a low state when +5V output voltage falls below under voltage threshold, or when AC power has been removed for a time sufficiently such that power supply operation cannot work normally. The electrical and timing characteristics of the PWR_OK signal are given in Table 8. and in figure 1.

Signal type

+5V TTL compatible

Logic level low

Less than 0.4V while sinking 10mA

Logic level high

Greater than 4.75V while sourcing 200uA

High-state output impedance

1k from output to common

PWR_OK delay

100ms < T3 <500ms

PWR_OK rise time

T4 10ms

AC loss to PWR_OK hold-up Time

T5 12ms (at 75% of maximum rated output load)

Power-down warning

T6 1ms

Table 8. PWR_OK Signal Characteristics

2.3.2. PS_ON (DC Soft Start)
PS_ON is an active-low, TTL-compatible signal that allows a motherboard to remotely control the power supply in conjunction with features such as soft on/off, Wake on LAN, or wake-on modem. When PS_ON is pulled to low-level (1.5V max.), the power supply will turn on the main DC output rails: +12V, +5V, +3.3V, and 12V. When PS_ON is pulled to high-level (2.4V min.), the DC output rails will not deliver current and will be held at zero potential with respect to ground. PS_ON has no effect to the +5Vsb output, which is always enabled whenever the AC power is present. Table 9. lists PS_ON signal characteristics.

Min

VIL, Input Low Voltage

0.0V

IIL, Input Low Current (Vin = 0.4V)

VIH, Input high Voltage (lin = -200uA)

2.4V

VIH, open circuit, lin =0

Table 9. PS_ON Signal Characteristics

Max 1.5V -1.6mA
5.25V

2.3.3. +5Vsb (Standby Voltage Output)
+5Vsb is a standby voltage output that is active whenever the AC power is present. It provides a power source for circuits that must remain operational when the four main DC output rails are in a disabled state. Example uses include soft power control, Wake on LAN, wake on modem, intrusion detection, or suspend state activities. There is over current protection on the +5Vsb output to ensure the power supply will not be damaged if external circuits draw more current than the supply can provide.

2.3.4. Power-on Time
The power-on time is defined as the time from when PS_ON is pulled low to when the12V, +5V, and +3.3V output are within the regulation ranges specified in Section 2.2.1. The power-on time will be less than 200ms (T1 <200 ms). +5Vsb has a power on time of one second max. after the valid AC Voltages applied.

2.3.5. Rise Time
The output voltage rises from 10% of nominal to within the regulation ranges specified in section 2.2.1 within 0.1 ms to 20 ms (0.1 ms T2 20 ms)

2.3.6. Power Sequencing
The +12V and +5V output levels are equal to or greater than the +3.3V output at all times during power-up and normal operation. The time between the +12V or +5V output reaching its minimum in-regulation level and +3.3V reaching its minimum in-regulation level is 20 msec.
05

2.3.7. Overshoot at Turn-on / Turn-off The output voltage overshoot upon the application or removal of the input voltage, or the assertion / de-assertion of PS_ON will be less than 10% above the nominal voltage.
2.3.8. Reset after Shutdown If the power supply latches into a shutdown state because of a fault condition on its outputs, the power supply can return to normal operation only after the fault condition has been removed and the PS_ON has been cycled OFF/ON with a minimum OFF time of 1 second.

2.3.9. +5Vsb at AC Power-down
After AC power is removed, the +5Vsb standby voltage output will remain at its steady state value for the minimum hold-up time specified in Section 2.2.6 until the output begins to decrease in voltage. The decrease can be monotonic in nature, dropping to 0.0V. There are no other perturbations of this voltage at or following removal of AC power.

2.4. Output Protection

2.4.1. Over Voltage Protection
The power supply can provide latch-mode over voltage protection as defined in Table 10.

Output +12Vdc +5Vdc +3.3Vdc

Min.

Nom.

Max.

13.6

14.6

15.6

5.5

6.25

7.0

3.7

4.1

4.5

Table 10. Over Voltage Protection

Unit Volts Volts Volts

2.4.2. Short-circuit Protection
The power supply will shut down and latch off for shorting the +12VDC, +5VDC, +3.3VDC, and -12VDC rails to return or any other rails. Shorts between main output rails and +5Vsb will not cause any damage to power supply. +5Vsb can be capable of being shorted indefinitely, but when the short is removed, the power supply will recover automatically or by cycling PS_ON. The power supply can be capable of withstanding a continuous short circuit to the output without damage or overstress to the unit under the input conditions specified in section 2.1.

2.4.3. Over Power Protection Fold back at 120%~150% over peak load

2.4.4. Over Temperature Protection
When OTP is triggered, the main outputs will be latched off. The main outputs can be reset by cycling the DC remote on/off or AC power. +5Vsb output is auto recovery when fault condition removed.
2.4.5. No-load Operation
No damage or hazardous condition will occur with all the DC output connectors disconnected from the load. The power supply may latch into the shutdown state.

2.4.6. Isolation (High Voltage Withstand)

Primary to Secondary Primary to Earth GND

4242Vdc 2800Vdc

3. Environmental
The following subsections define recommended environmental specifications and test parameters. Based on the typical conditions to which an ATX power supply may be subjected during operation or shipment.

3.1. Temperature

Operating Non-operating

0 to +40 -20 to +70

3.2. Humidity
Operating Non-operating
3.3. Altitude Operating Storage

20% to 90% relative humidity (non-condensing) 5% to 95% relative humidity (non-condensing)
0 to 10,000 feet 0 to 50,000 feet

4. Electromagnetic Compatibility The following subsections outline applicable product regulatory specifications for this power supply.
4.1. Emissions The power supply can comply with FCC Part 15 and EN55022: 2006 meeting Class B for both conducted and radiated emissions with a 3 dB margin.

4.2. Immunity
The power supply can comply with FCC Part 15 and EN55022: 2006 meeting Class B for both conducted and radiated emissions with a 3 dB margin.

4.3. CE Testing(design to meet)

The following standards are applied during the CE testing

EN 55032: 2012 EN 61000-3-2: 2014 EN 61000-3-3: 2013 EN 55024: 2010, including IEC 61000-4-2: 2009 IEC 61000-4-3: 2010 IEC 61000-4-4: 2012 IEC 61000-4-5: 2014 IEC 61000-4-6: 2013 IEC 61000-4-8: 2010 IEC 61000-4-11: 2004

Class B with 3dB margin minimum Harmonic Current Measurement Voltage Fluctuation and Flick Measurement
ESD air discharge 8kV / ESD contact discharge 6kV Radiated, Radio Frequency Electromagnetic Field Immunity Test Electrical Fast Transient/Burst Immunity Test:2kV Surge Immunity Test 4kV L/N to PE and 2kV L to N Immunity to Conducted Disturbances Induced by RF Fields Power Frequency Magnetic Field Immunity Test Voltage Dips and Short Interruptions Immunity Test

5.Reliability

5.1. Component De-rating

The derating process promotes quality and high reliability. All electronic components are designed with conservative derating for use in commercial and industrial environments.
5.2. Mean Time between Failures (MTBF)

100K hours minimum at full load 25 per MIL-HDBK-217F 6. Mechanical

Dimension W x L x H = 100 x 125 x 63.5mm

7. POWER SUPPLY CONNECTOR OVERUSE DEFINITION

EN Power supply connector overuse definition
A single PCIe 8pin cable and connector’s maximum current rating is 12.5A, which is 150W (+12V x 12.5A). So SilverStone’s warranty will not cover damages or malfunction resulting from the use of a graphics card or expansion card with a single PCIe 8pin connector that exceeds standard 225W total power draw (150W from PCIe 8pin connector + 75W from PCIe motherboard slot). Similarly, a graphics card or expansion card with dual PCIe 8pin connectors that exceed 375W total power draw (300W from two PCIe 8pin connectors + 75W from PCIe motherboard slot) will also not be covered under warranty.
Peripheral (molex) or SATA connector’s maximum current rating is 5A, which is 60W (+12V x 5A) or 25W (+5V x 5A). Please ensure connected devices are operating under these limits. SilverStone’s warranty will not cover damages or malfunction resulting from usages exceeding these connectors and their associated cables.
24pin motherboard connector’s maximum current rating for its dual +12V metal pins are 5A each, which totals 120W (+12V x 5A x 2). Please ensure +12V drawing devices connected to the motherboard are operating under these limits. SilverStone’s warranty will not cover damages or malfunction resulting from usages exceeding these connectors and their associated cables.
DE Definition einer Überlastung des Netzanschlusses
Die maximale Stromstärke eines einzelnen 8-poligen PCIe-Kabels und Anschlusses beträgt 12,5 A, was 150 W (+12 V x 12,5 A) entspricht. Daher deckt die SilverStone-Garantie keine Schäden oder Fehlfunktionen durch den Einsatz einer Grafikkarte oder Erweiterungskarte mit einem einzigen 8-poligen PCIe-Anschluss ab, die die Standardleistungsaufnahme von insgesamt 225 W übersteigt (150 W vom 8-poligen PCIe-Anschluss + 75 W vom PCIe-Motherboard-Steckplatz). Ebenso wird die Verwendung einer Grafikkarte oder Erweiterungskarte mit zwei 8-poligen PCIe-Anschlüssen, die eine Leistungsaufnahme von insgesamt 375 übersteigen (300 W von den beiden 8-poligen PCIe-Anschlüssen + 75 W vom PCIe-Motherboard-Steckplatz) nicht durch die Garantie abgedeckt.
Der maximale Nennstrom von Peripherie- (Molex) oder SATA-Anschluss beträgt 5 A, was 60 W (+12 V x 5 A) oder 25 W (+5 V x 5 A) entspricht. Bitte achten Sie darauf, dass verbundene Geräte unter diesen Grenzwerten arbeiten. Die Garantie von SilverStone deckt keine Schäden oder Fehlfunktionen aufgrund einer Nutzung ab, die diese Anschlüsse und ihre zugehörigen Kabel übersteigt.
Der maximale Nennstrom des 24-poligen Motherboard-Anschlusses für seine dualen +12-V-Metallkontakte beträgt jeweils 5 A, was insgesamt 120 W (+12 V x 5 A x 2) ergibt. Bitte stellen Sie sicher, dass mit dem Motherboard verbundene +12-V-Geräte unter diesen Grenzwerten arbeiten. SilverStones Garantie deckt keine Schäden oder Fehlfunktionen aufgrund einer Nutzung jenseits der Angaben dieser Anschlüsse und ihrer zugehörigen Kabel ab.
FR Définition de l’utilisation excessive du connecteur d’alimentation électrique
Le courant nominal maximum d’un câble et d’un connecteur PCIe 8 broches unique est de 12,5 A, ce qui correspond à 150 W (+12 V x 12,5 A). La garantie de SilverStone ne couvre donc pas les dommages ou les dysfonctionnements résultant de l’utilisation d’une carte graphique ou d’une carte d’extension avec un connecteur PCIe 8 broches unique qui dépasse une consommation énergétique totale de 225 W standard (150 W provenant du connecteur PCIe 8 broches + 75 W provenant de l’emplacement de la carte mère PCIe). De même, une carte graphique ou une carte d’extension avec deux connecteurs PCIe 8 broches qui dépasse une consommation énergétique totale de 375 W (300 W provenant des deux connecteurs PCIe 8 broches + 75 W provenant de l’emplacement de la carte mère PCIe) ne sera également pas couverte dans le cadre de la garantie.

Le courant nominal maximum d’un périphérique (Molex) ou d’un connecteur SATA est de 5 A, ce qui correspond à 60 W (+12 V x 5 A) ou 25 W (+5 V x 5 A). Veuillez vous assurer que les appareils connectés fonctionnent dans ces limites. La garantie de SilverStone ne couvre pas les dommages ou les dysfonctionnements résultant d’utilisations dépassant ces connecteurs et leurs câbles associés.

Le courant nominal maximal des connecteurs 24 broches de la carte mère pour ses doubles broches métalliques +12 V est de 5 A chacun, ce qui représente au total 120 W (+12 V x 5 A x 2). Veuillez vous assurer que les dispositifs de tension +12 V connectés à la carte mère fonctionnent dans ces limites. La garantie de SilverStone ne couvre pas les dommages ou les dysfonctionnements résultant d’utilisations dépassant la capacité de ces connecteurs et de leurs câbles associés.

Definizione di uso eccessivo del connettore di alimentazione

La corrente massima di un singolo cavo PCIe a 8 pin e del connettore è 12,5 A, corrispondente a 150 W (+12 V x 12,5 A). Pertanto, la garanzia di SilverStone non copre danni o malfunzionamenti derivanti dall’utilizzo di una scheda grafica o una scheda di espansione con un singolo connettore PCIe a 8 pin che supera l’assorbimento totale di 225 W (150 W da connettore PCIe a 8 pin + 75 W da slot PCIe). Analogamente, la garanzia non copre anche una scheda grafica o una scheda di espansione con doppi connettori PCIe a 8 pin che superano l’assorbimento totale di 375 W (300 W da doppi connettori PCIe a 8 pin + 75 W dalla scheda madre PCIe).
La corrente massima del connettore periferico (molex) o SATA è 5 A, corrispondente a 60 W (+12 V x 5 A) o 25 W (+5 V x 5 A). Assicurarsi che i dispositivi collegati funzionino entro questi limiti. La garanzia di SilverStone non copre danni o malfunzionamenti derivanti da uso eccessivo di questi connettori e dei relativi cavi.
La corrente massima del connettore a 24 pin per scheda madre per i suoi due pin di metallo a +12 V è di 5 A ciascuno, per un totale di 120 W (+12 V x 5 A x 2). Assicurarsi che i dispositivi a +12 V collegati alla scheda madre funzionino con questi limiti. La garanzia di SilverStone non copre danni o malfunzionamenti derivanti da uso eccessivo di questi connettori e dei relativi cavi.
ES Definición de uso excesivo del conector de la Fuente de alimentación

La corriente máxima de un solo cable PCIe de 8 pines es 12,5A, lo que son 150W (+12V x 12,5A). Por tanto, la garantía de SilverStone no cubrirá daños o fallos provocados por el uso de una tarjeta gráfica o de expansión con un único conector PCIe de 8 pines que exceda el total estándar de 225W (150W del conector PCIe de 8 pines + 75W del zócalo PCIe de la placa base). De igual modo, una tarjeta gráfica o de expansión con conectores duales PCIe de 8 pines que superen 375W de potencia (300W de los dos conectores PCIe de 8 pines + 75W del zócalo de la placa base) tampoco será cubierta por la garantía.
La corriente máxima del conector de periféricos (molex) o SATA es 5A, que son 60W (+12V x 5A) o 25W (+5V x 5A). Por favor, asegúrese de que los dispositivos conectados funcionan dentro de estos límites. La garantía de SilverStone no cubrirá daños o fallos a resultas de un uso excesivo de estos conectores y sus cables asociados.
La corriente máxima del conector de 24 pines de la placa base para sus pines de metal duales de +12V es de 5A cada uno, para un total de 120W (+12V x 5A x 2). Por favor, asegúrese de que los dispositivos de +12V conectados a la placa base funcionan dentro de estos límites. La garantía de SilverStone no cubrirá daños o averías a resultas de un uso excesivo para estos conectores y sus cables asociados.

RU
PCIe 8pin 12.5A, 150 (+12 x 12.5A). , SilverStone PCIe 8pin, 225 (150 PCIe 8pin + 75 PCIe ). , PCIe 8pin, 375 (300 PCIe 8pin + 75 PCIe ), .

(molex) SATA 5A, 60 (+12 x 5A) 25 (+5 x 5A). , , . SilverStone , .
24pin +12 5A , 120 (+12 x 5A x 2). , , , +12, . SilverStone , .

CN
3&,HSLQ$: 9[$3&,H SLQ: :3&,HSLQ:3&,H 3&,HSLQ: :3&,HSLQ: 3&,H

SLQPROH[6$7$$:9[ $:9[$
SLQ9$: 9[$[9
TW
3&,HSLQ$: 9[$3&,H SLQ: :3&,HSLQ:3&,H 3&,HSLQ: :3&,HSLQ: 3&,H
SLQPROH[6$7$$:9[ $:9[$
SLQ9$: 9[$[9

TH
PCIe 8 12.5 150 (+12V x 12.5A) SilverStone PCIe 8 225 (150 PCIe 8 + 75 PCIe ) PCIe 8 2 375 (300 PCIe 8 2 + 75 PCIe )

Peripheral Molex 4 SATA 5 60 (+12V x 5A) (+5V + 5A) SilverStone 24 +12V 5A 120W (+12V x 5A x 2) +12V SilverStone

PP PPPP

PP Openings that do not exceed 5mm in any dimension
PP
PP Openings that do not exceed 1mm in width regardless of length

%60,52+6 KWWSZZZVLOYHUVWRQHWHNFRPGRZQORDGV36856’SGI
11

5IJTEFWJDFDPNQMJFTXJUI1BSUPGUIF’$$3VMFT
0QFSBUJPOJTTVCKFDUUPUIFGPMMPXJOHUXPDPOEJUJPOT

UIJTEFWJDFNBZOPUDBVTFIBSNGVMJOUFSGFSFODF
BOE
UIJTEFWJDFNVTUBDDFQUBOZJOUFSGFSFODFSFDFJWFE
JODMVEJOHJOUFSGFSFODFUIBUNBZDBVTFVOEFTJSFEPQFSBUJPO
12
Model: SST-SX0350FCBR-A SST-SX0450FCBR-A SST-SX0500FCBR-A
1MFBTFSFGFSUP4JMWFS4UPOFXFCTJUFGPSMBUFTUTQFDJpDBUJPOTVQEBUFT
12

NO. G11242291

Silverstone Sst-ex350-bf Extreme 350 Bronze User Manual

SST-EX350-BF Extreme 350 Bronze

Product Information

Specifications:

Product Usage Instructions

Documents / Resouces

Related Manuals