Rangehoods Fitted with Plasma Norm Filter
Product Information
The Rangecraft Rangehood is a high-quality kitchen appliance
designed to efficiently extract smoke, steam, and odors from your
cooking area. It is suitable for use with all domestic cookware
available in the Australian market. The rangehood is equipped with
a Plasma-Norm Filter, which helps to effectively remove airborne
particles and ensure clean air in your kitchen.
Key Features:
- Available in various models, including compact, undercupboard,
and suitable for induction cooktops - LED lights with a night light feature
- Ducted installation for optimal performance
- Minimum distance requirements above trivets of gas hotplates
and induction cooktops - Return air opening for efficient airflow
- Maintenance and filter replacement recommendations
Product Usage Instructions
- Ensure the installation of the Rangecraft Rangehood complies
with the information provided in the user manual. - Choose the appropriate model based on your kitchen setup and
requirements. - For gas hotplates, install the rangehood at least 600mm above
the trivets. For induction cooktops, the minimum distance should be
750mm, except for the RPEP model, which requires a 600mm
distance. - Duct the rangehood using stainless, zinc-alume duct, or other
non-porous and non-flammable materials. Do not use flexible ducting
or plastic PVC piping. - The cross-sectional area of the rangehood outlet and the duct
work must be equal to ensure efficient airflow. Do not reduce the
duct size or have sharp bends. Contact CONDARI for advice to ensure
optimum performance. - Ensure all ducting pieces are correctly fitted and sealed with
duct tape or silicone to prevent fumes from escaping into the
ceiling space or living areas. - Properly ventilate the room when using the rangehood
simultaneously with gas or other fuel-burning appliances. - Maintain a minimum return air opening of 400cm2. It is
recommended to have a larger opening to minimize air noise. - Regularly maintain and service the rangehood by a qualified
person. Replace the Plasma-Norm Filter every 4-5 years, depending
on use.
Following these instructions will ensure the safe and effective
use of your Rangecraft Rangehood, providing you with a clean and
odor-free kitchen environment.
Rangecraft Rangehood Pricelist
Rangecraft Ra1nJagneuahryo2o01d7
Installation Instructions
December 2018
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
IMPORTANT INFORMATION
Rangecraft rangehoods can be installed at 600mm above the trivets of a gas hotplate. Over an induction cooktop the minimum should be 750mm, with the exception of the RPEP, which must be installed at 600mm
1. The installation of Rangecraft Rangehoods must comply with the information in this booklet. Rangecraft Rangehoods are designed and made to work efficiently over all domestic cookware available on the Australian market.
2. Every Rangecraft Rangehood must be ducted by the use of stainless, zinc-alume duct or non-porous and non-flammable materials. Do not use any type of flexible ducting or plastic PVC piping.
3. Rangecraft Rangehoods must be ducted in duct work equivalent to the outlet of the rangehood ie: The cross sectional area of the rangehood outlet and the duct work must be equal. Do not reduce the duct size or have sharp bends. Advice from CONDARI is available to ensure optimum performance. Always use nonflammable materials to minimise the risk of fire in the duct.
4. Ensure all ducting pieces are correctly fitted and sealed with either duct tape or silicone to ensure that fumes do not escape into the ceiling space and seep into living areas through vents or light fittings. The installation and fitting of the rangehood and plasma filter should be done in such a way that will allow the unit to be removed if service is required. Additional costs incurred in the removal of wall tiles, damage to walls or bench tops are not covered by warranty.
5. Always adequately ventilate the room when the rangehood is in use at the same time as appliances burning gas or other fuels.
6. WARNING: Incorrect venting will result in additional noise and a reduction in efficiency. Exhaust air must not be discharged into any chimney or flue, which may carry combustible products from other sources. a. Do not discharge the air-flow from the rangehood into a flue used for exhausting fumes from burning gas or fuel; b. Some parts of the rangehood may become hot when cooking; c. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
7. Do not flambé under the rangehood. 8. If the supply cord is damaged, an authorised service centre or licensed electrician must
replace it. 9. The lights in the rangehoods are LED and come with a night light 10. To reduce the risk of fixing screws coming in contact with live parts, do not drill or screw
into the rangehood. Live wires are encapsulated where possible to prevent user contact. If necessary drill from the inside out and only through single sheet material. 11. Rangecraft domestic rangehoods are not to be used over barbecues approved for outdoor use only, with a Mega Joule rating of 50mj and over. 12. CONDARI make a range of hoods specifically for outdoor barbecues in alfresco areas under the CONDOR name. 13. CONDARI can manufacture rangehoods to be used over commercial cookers in domestic applications.
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
MODELS AVAILABLE
RPCP 60-1 T RPCP 90-1 T
Compact 60cm rangehood, top ducted Compact 90cm rangehood, top ducted
RPUC 60-1 T RPUC 90-1 T
Undercupboard 60cm rangehood, top ducted Undercupboard 90cm rangehood, top ducted
Rangehoods suitable over induction cooktops
RPWP 60-1 T
Undercupbord 60cm rangehood, top ducted
RPWP 100-1 T Undercupbord 100cm rangehood, top ducted
RPEP 60-1 T RPEP 100-1 T
Undercupbord 60cm rangehood, top ducted Undercupbord 100cm rangehood, top ducted
· Height required to accommodate Plasma filter will vary depending on Plasma unit used See page (4) for details
· The Plasma can be installed up to 6 metres from rangehood · Return air MUST recirculate back into the same room via a vent in the
cabinetry / ceiling / bulkhead · The Plasma vent must be a minimum 400cm² to allow for adequate return
of the air into the room · Plasma filters can be installed on an angle · Plasma filters must be easily accessible for maintenance. · Use only rigid ducting
Ceiling
150mm dia.
Maximum 6 metres
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
Rangecraft Rangehood Return Air Opening
The Cabinet/Bulkhead that houses the Plasma Unit of the Rangecraft Rangehood must have an opening in it to allow air to recirculate back into the room. This opening must have an unobstructed minimum area of 400cm2. For example, this opening may be 20cm X 20cm or 16cm X 25cm or 10cm X 40cm for each Plasma unit installed. This opening may be on the top, front or side of the cabinet, it may be orientated vertically or horizontally as long as its in the same room as the Rangehood. The opening must not be made in the bottom of an overhead cabinet.
20cm x 20cm 400cm2
10cm x 40cm 400cm2
Dia 22.6cm 400cm2
Please note 400cm2 is the minimum opening requirement, Condari advises that the return air opening should be as large as practically possible for the application, to reduce the possibility of air noise from the air returning to the kitchen.
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
Maintaining your Plasma-Norm
A qualified person should only carry out Rangecraft servicing. THE CARBON FILTER SHOULD BE REPLACED EVERY 4-5 YEARS DEPENDING ON USE.
5IFSFBSF1MBTNBmMUFSTBWBJMBCMF PNF 143-2 Filter
262633.0.0
212111.0.0
404303..00
323200.0.0
PNF 103-2 Filter
263.0 263.0
211.0 211.0
502.0 502.0
320.0 320.0
PNF 220-1 Filter
151588.0.0
606000.0.0
272700.0.0
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
MODEL
RPUC 60-1 T RPUC 90-1
R/HOOD SIZE
243 X 580 243 X 880
RPWP 60-1 T 290 X 565 RPWP 100-1 T 290 X 980
RPEP 60-1 T 290 X 565 RPEP 100-1 T 290 X 980
BASE SIZE
280 X 600 280 X 900
330 X 600 330 X 1000
330 X 600 330 X 1000
PROUD MOUNT CUT OUT DIMENSION
258 X 585 258 X 885
FLUSH MOUNT CUT OUT DIMENSION
280 X 600 280 X 900
300 X 570 300 X 985
330 X 600 330 X 1000
300 X 570 300 X 985
330 X 600 330 X 1000
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
Installation instructions · RPCP
1. Prepare wall by marking level line at desired height above cooktop. 2. Plumb line from centre of cooktop to ceiling and mark flue cut out. 3. Mark level line for base of canopy 700-800mm above bench 750mm desirable. 4. Position mounting bracket on wall and fix with four screws. 5. Locate solid fixing point in wall to support rangehood. If there is no solid fixing point it will
have to be placed in the wall before proceeding. Condari recommend at least four (4) fixing points. 6. Drill holes in back of unit at suitable fixing points. 7. Drill 20mm hole in the rear of unit for 240 volt power cable as close as possible to junction or use hole below the junction box. 8. Install the Plasma unit on top of the Rangehood and plug in the connector. 9. If the Plasma is being installed remotely from the rangehood, fit required 150 diameter rigid duct pieces and use PEL extension lead for the Plasma filter. 10. Ensure to follow Plasma filter rules located on page 1
RANGECRAFT Technical Specification Sheet
RPCP
Fascia with Concealed Motorbox
Power entry location is the same for all RPCP models.
415
100
280 510
Model Body Width Motor Box / Flue Width Motor Qty LED Light Nightlight Light Qty Light Centres Filter Qty
RPCP 60-1 600mm 435mm 1 Cool YES 1 Centre 2
RPCP 90-1 900mm 435mm 1 Cool YES 2 525mm 2
Model
RPCP 60-1
RPCP 90-1
Filter Size Conversion Top/Back Back/Top
Electrical Connection Minimum Height (H =) Maximum Height (H =) PowderKote } Available All-thread Fixing Centres
Corner Type
272mm x 355mm NO
Junction Box N/A N/A N/A N/A
Square
422mm x 355mm NO
Junction Box N/A N/A N/A N/A
Square
Condari Pty Ltd.
Version: B 18/08/2017F Page 1 of 1
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
Installation instructions · RPUC
1. Loosen scres A & B by turning anti-clockwise. 2. Turn screw D anti clockwise to extend the outer spring bracket. 3. Insert rangehood into cut out and turn screw C clockwise to align with cupboard base. 4. Do not over tighten. 5. Tighten screw A by turning clockwise to lock fixing bracket. 1. Loosen scre6w.s ATaonrdemBobvyetruarnngineghaonotdi-,ctluorcnkwscisreew. D clockwise. 2. Turn screw `7D.’ anIntis-tcalollctkhweiPselatsomeaxtuennidt othnetooputifetrhsepRrinagngberahcokoedt.and plug in the connector. Insert rangeh8o. odIfinthtoe cPultaosumtaanisd btuerinngscirneswta`lCle’dclroecmkwotiesley tforoamlignthreanragnegheohoodowd,ithfitcurepqbuoiarerdd b1a5s0e.diameter Do not over tightreigni.d duct pieces and use PEL extension lead for the Plasma filter. Tighten scre9w. `AE’ bnysuturerntiongfocllloowckPwliassemtoa lfoilctekrfrixuilnegs blorcaactkeedt.on page 1
To remove rangehood, turn screw `D’ clockwise.
RANGEHOOD SPRING BRACKETS
Models: RPLIUS C 60
CON
Models: RPEUTCN 90
ECH NDCH
MOUNTING POSITION
Cupboard
Front of Rangehood 12
PROUD MOUNT
Cupboard
Front of Rangehood 12
FLUSH MOUNT
RANGECRAFT Technical Specification Sheet
RPUC
Concealed
Cabinet Cut-Out
Cabinet Cut-Out
Power Entry
360 12
240
280
Power Entry
Model Body Width Motor Box / Flue Width Motor Qty LED Light Nightlight Light Qty Light Centres Filter Qty
RPUC 60-1 600mm 580mm 1 Cool YES 1 Centre 2
RPUC 90-1 900mm 880mm 1 Cool YES 2 770mm 2
Model
RPUC 60-1
RPUC 90-1
Filter Size Conversion Top/Back Back/Top
Electrical Connection Minimum Height (H =) Maximum Height (H =) PowderKote } Available
Cabinet Cut-Out
269mm x 250mm NO
10 Amp Lead N/A N/A N/A
258mm X 585mm
340mm x 260mm NO
10 Amp Lead N/A N/A N/A
258mm X 885mm
Corner Type
Square
Square
Condari Pty Ltd.
Version: F 18/08/2017F Page 1 of 1
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
Installation instructions · RPWP / RPEP
1. Loosen screws A and B by turning anti clockwise 2. Turn D anti clockwise to extend the outer spring bracket. 3. Insert rangehood into cut out and turn screw C clockwise to align rangehood with
cupboard base. 4. Do not over tighten. 5. Tighten screw A by turning clockwise to lock fixing bracket. 6. Fit off ductwork as required. 1. Loosen s7c.rewTsoAreamndoBvebryatnugrneihngooadn,tit-ucrloncskcwriesew. D clockwise. 2. Turn `D’ a8n.ti-cInlosctkawllistheetoPelaxstemnad uthneitoountetrospporifntghberaRcaknegt.ehood and plug in the connector. Insert ran9g.ehIofotdheintPolcaustmoautiasnbdetiunrgn sincsretawlle`Cd’ crelomckowteislye tforoamlignthreanrgaenhgoeohdoowdit,hfcituprebqouairrdedba1s5e0. diameter Do not over tirgighitdend.uct pieces and use PEL extension lead for the Plasma filter. Tighten s1c0re.wE`nAs’ ubryetutornfionlglocwloPcklawsismeatofilltoecrkrfuixleinsglobcraactekedt.on page 1
To reTmhoeveRrPaWngPehRoaondg, teuhrnooscdremwu`Dst’ cbleociknwsitsael.led at a minimum of 750mm over induction cooktops. The RPEP Rangehood must be installed at 600mm over induction cooktops.
RANGEHOOD SPRING BRACKETS Model: RWPEESP
A
B C
D
Model: RPEWASP A
B
C D
WESTMORE
MOUNTING POSITION
Cupboard
Front of Rangehood 12
PROUD MOUNT
Cupboard
Front of Rangehood 12
FLUSH MOUNT
RANGECRAFT Technical Specification Sheet
RPWP
Cabinet Cut-Out
Motor Access Panel
Cabinet Cut-Out
Concealed
Power Entry
450 12
290 330
Motor Access Panel
Power Entry
Model Body Width Motor Box / Flue Width Motor Qty LED Light Nightlight Light Qty Light Centres Filter Qty
RPWP 60-1 600mm 565mm 1 Cool YES 2 300mm 2
RPWP 100-1 1000mm 980mm 1 Cool YES 2 480mm 2
Model
RPWP 60-1
RPWP 100-1
Filter Size Conversion Top/Back Back/Top
Electrical Connection Minimum Height (H =) Maximum Height (H =) PowderKote } Available
Cabinet Cut-Out
272mm x 272mm NO
10 Amp Lead N/A N/A N/A
300mm X 570mm
479mm x 260mm NO
10 Amp Lead N/A N/A N/A
300mm X 985mm
Corner Type
Square
Square
Condari Pty Ltd.
Version: E 18/08/2017F Page 1 of 1
RANGECRAFT Technical Specification Sheet
RPEP
Cabinet Cut-Out
Motor Access Panel
Cabinet Cut-Out
Concealed
Power Entry
570
12
290 330
Motor Access Panel
Power Entry
Model Body Width Motor Box / Flue Width Motor Qty LED Light Nightlight Light Qty Light Centres Filter Qty
RPEP 60-1 600mm 565mm 1 Cool YES 2 300mm 2
RPEP 100-1 1000mm 980mm 1 Cool YES 2 480mm 2
Model
RPEP 60-1
RPEP 100-1
Filter Size Conversion Top/Back Back/Top
Electrical Connection Minimum Height (H =) Maximum Height (H =) PowderKote } Available
Cabinet Cut-Out
272mm x 272mm NO
10 Amp Lead N/A N/A N/A
300mm X 570mm
479mm x 260mm NO
10 Amp Lead N/A N/A N/A
300mm X 985mm
Corner Type
Square
Square
Condari Pty Ltd.
Version: E 18/08/2017F Page 1 of 1
Installation instructions Rangecraft Rangehoods Fitted with Plasma-Norm Filter
Rangecraft spare parts available
· PEL 1M – Plasma extension lead 1 meter · PEL 2M – Plasma extension lead 2 meter · PEL 3M – Plasma extension lead 3 meter · PEL 4M – Plasma extension lead 4 meter · PEL 5M – Plasma extension lead 5 meter · PEL 6M – Plasma extension lead 6 meter
Ceiling
Rangecraft ducting available
· RDR 45 (45 degree bend) · RDR 90 (90 degree bend) N15N0EmJBmNdFiUFaS. · RDL 300 (300mm duct length) · RDL 600 (600mm duct length) · RDL 900 (900mm duct length)
RDR-900
Maximum 6 metres
Rangecraft
ducting pieces
available
P
3%30
P
RDL-300
RDL-600
RDL-900
PTY LTD
Distributed in Australia by Condari Pty Ltd. 5 www.qasair.com.au www.condari.com.au
)FBEPGmDF7*$
T 03 9482 7088
F 03 9482 7011
Email: [email protected]
NSW / ACT
5 ‘ Email: [email protected]
QLD
5 ‘ Email: [email protected]
SA / NT
5 ‘ Email: [email protected]
TAS
T 03 9482 7088
F 03 9482 7011
Email: [email protected]
WA
5 ‘ Email: [email protected]
New Zealand – Kouzina Appliances T +64 9 377 7822 F +64 9 377 7824 Email: [email protected]
Singapore – Eldric Marketing 5 ‘ Email: [email protected]
CONDARI Rangehoods made in Ringwood 3134
$POEBSJ1-SFTFSWFTUIFSJHIUUPDIBOHFTQFDJmDBUJPOXJUIPVUOPUJDF¥JTBSFHJTUFSFEUSBEFNBSL
plasmaNorm® is a registered trade mark of Airtec Competence GmbH, Germany.
www.qasair.com.au
www.condari.com.au
www.condari.com.au
CONDARI - Qasair and Condor Rangehoods, BBQs & More
CONDARI - Qasair and Condor Rangehoods, BBQs & More
