CFN-1105 52 Inch LED Indoor Silver Flush Mount Ceiling Fan
Product Information
The CFN-1105 is a fan and light kit designed for indoor use. The
package includes fan blades, mounting bracket, fan motor, light
plate, LED light kit, shade, remote control, receiver, wood screws,
plastic washers, anchor bolts, spare blade arm bolts, metal
washers, wire nuts, spare motor bolts, gloves, balance clip,
balance tabs and blade bolts. Additional tools required for
assembly include electrical tape, flathead & Phillips
screwdriver, pliers, safety glasses, ladder, and wire strippers.
Additional helpful tools include AC tester light, tape measure,
wiring handbook, and wire cutters.
Product Usage Instructions
- Before beginning installation, read the package list to ensure
all parts are present and display no defects. If any part is
missing or damaged, contact customer service and do not attempt to
install the product. - Read all of the safety information provided in the user manual
before installation or use. - Turn off electricity at the circuit breaker or fuse box before
beginning installation. - All wiring must be in accordance with national and local
electrical codes. Electrical installation should be performed by a
qualified licensed electrician. - The fan must be mounted with a minimum of 7 feet clearance from
the trailing edge of the blades to the floor. - Use only UL listed junction boxes marked FOR FAN SUPPORT for
mounting the fan to a junction box. - After marking electrical connections, spliced conductors should
be turned upward and pushed carefully up into the junction box. The
wires should be spread apart with the grounded conductor and the
equipment-grounding conductor on one side of the junction box. - Do not use the reverse switch while the fan blades are in
motion. To prevent damage and ensure long use, the fan must be
turned off and the blades stopped before reversing direction. - Do not place objects in the path of the blades.
- Exercise caution when working around or cleaning the fan. Use a
soft dry cloth to clean the fan body and blades. Do not use water
or detergent. - The electrical diagrams provided herein are for reference only.
Light kits that are not packaged with the fan must be UL listed and
suitable for use with this fan. Switches must be UL general use
switches. Refer to their separate instructions for proper
assembly. - Never bend the blades for any reason.
V20220439
CFN-1105 User Manual
Read Carefully Before Use Keep for Future Reference
CONTENTS
Introduction…………………………………………………………………………………………… 1 Package List………………………………………………………………………………………….. 2 Safety Information …………………………………………………………………………………. 3 Preparation …………………………………………………………………………………………… 4 Initial Installation …………………………………………………………………………………… 5 Circuit Connections ………………………………………………………………………………. 5 Fan Motor Mounting ………………………………………………………………………………. 6 Blade Installation…………………………………………………………………………………… 6 Light Installation……………………………………………………………………………………. 7 Color Temperature Adjustment ………………………………………………………………. 8 Remote Control Operation……………………………………………………………………… 8 Troubleshooting ……………………………………………………………………………………. 9 Contact Information …………………………………………………………………………….. 10
Introduction
Before beginning installation of this product, read the package list on page 2 and ensure all parts are present and display no defects. If any part is missing or damaged, contact customer service and do not attempt to install the product. Read all of the safety information on page 3 before installation or use. Estimated assembly time: 120 minutes Additional tools required for assembly: Electrical tape, flathead & Phillips screwdriver, pliers, safety glasses, ladder, and wire strippers
Additional helpful tools: AC tester light, tape measure, wiring handbook, and wire cutters
1
Package List
B
G
H
C
D
E
A
F
I
Item
Name
Qty.
A Fan Blades
3
B Mounting Bracket
1
C Fan Motor
1
D Light Plate
1
E LED Light Kit
1
F Shade
1
G Remote Control
1
H Receiver
1
Wood Screws
4
Plastic Washers
11
Anchor Bolts
4
Spare Blade Arm Bolts
2
Metal Washers
4
I Wire Nuts
5
Spare Motor Bolts
2
Gloves
2
Balance Clip
1
Balance Tabs
2
Blade Bolts
11
2
Safety Information
Warning!
1. To reduce the risk of electric shock, ensure electricity has been turned off at the circuit breaker or fuse box before beginning.
2. All wiring must be in accordance with national and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.
3. This fan is suitable for use with solid-state speed controls. 4. To reduce the risk of personal injury, use only the fasteners provided with the junction box
for mounting to the junction box. Most junction boxes commonly used for the support of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if in doubt.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, & PERSONAL INJURY, MOUNT FAN TO A JUNCTION BOX MARKED “ACCEPTABLE FOR FAN SUPPORT”.
5. The junction box and support structure MUST be securely mounted and capable of reliably supporting a minimum of 50 pounds. Use only UL listed junction boxes marked “FOR FAN SUPPORT”.
6. After marking electrical connections, spliced conductors should be turned upward and pushed carefully up into the junction box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the junction box.
7. The fan must be mounted with a minimum of 7 feet clearance from the trailing edge of the blades to the floor.
8. Do not use the reverse switch while the fan blades are in motion. To prevent damage and ensure long use, the fan must be turned off and the blades stopped before reversing direction.
9. Do not place objects in the path of the blades. 10. Exercise caution when working around or cleaning the fan. 11. Use a soft dry cloth to clean the fan body and blades. Do not use water or detergent. 12. The electrical diagrams provided herein are for reference only. Light kits that are not
packaged with the fan must be UL listed and suitable for use with this fan. Switches must be UL general use switches. Refer to their separate instructions for proper assembly.
NEVER BEND THE BLADES FOR ANY REASON.
3
Preparation
1. Turn Off Your Power
Begin installation by removing fuses or turning off circuit breakers to the wiring you will be using. Use your compatible UL listed junction box if you already have one installed.
Failure to disconnect the power supply prior to installation may result in serious injury or death.
2. Choose Your Mounting Position
If you need to install a new UL listed junction box, secure it directly to your building’s structure usingappropriate fasteners and materials. Do not use plastic boxes. The junction box and its supports must be able to support the MOVING weight of the fan (at least 50 lb.) and be rated for fan support.
3. Choose a Suitable Location
Ensure the blades will be at least 30 inches from any obstruction and at least 7 feet above the floor. In locations without a ceiling joist, a hanger support bar may be required. Do not install in damp locations.
4
Initial Installation
Wood Ceiling
Mounting Bracket
Wood Screw
Supply Wires Metal Washer
Concrete Ceiling
Anchor Bolt
Step 1. Pass the supply wires from the junction box (not included) through the central hole of the mounting bracket.
Step 2. Secure the bracket to the junction box with the provided fasteners. Use the mounting screws and metal washers on wood ceilings or the anchor bolts on reinforced concrete or similar ceilings.
Circuit Connections
Again, ensure that the power has been cut before working with the wiring. Use the wire nuts provided with your fan.
Ensure there are no loose wires or connections, and secure connectors with electrical tape.
Step 1. Insert the receiver into the tray with the receiver facing the ceiling. For best results, make sure the white Black (L) antenna on the end of the receiver remains extended
and not tangled with any of the electrical wires.
Step 2. Connect the 4 colored wires of the receiver to the 4 identically colored wires of the fan motor. Secure each set with the provided wire nuts.
Step 3. Connect the 2 colored wires of the receiver to the 2 identically colored wires of the junction box. Secure each set with the provided wire nuts.
Blue Brown
Blue Brown
Step 4. Connect the green or bare copper ground wire of the junction box to the ground wire of the ceiling fan motor. Separate the white and green connections from the black wire connections, which should be kept on opposite sides of the junction box.
Step 5. Tuck all the connections neatly into the junction box.
Green or Bare Copper (Ground) White (N)
Antenna Receiver
White Black White Black
5
Fan Motor Mounting
DO NOT use the fan before ensuring it is properly secured and the motor cannot rotate. Step 1. Loosen the blade bolts on the rim of the mounting bracket. Step 2. Fit the top of the fan motor onto the mounting bracket, aligning its slots with the
loosened bolts. Step 3. Retighten these bolts.
Mounting Bracket Blade Bolt
Receiver
Fan Motor
Blade Installation
Step 1. Fit a blade onto one blade arm underneath the fan motor, aligning their slots with each other.
Step 2. Making sure the blade is straight, attach and tighten 3 plastic washers and blade bolts. Step 3. Repeat for the remaining blades.
Fan Motor Blade Arm
Blade
6
Light Installation
Step 1. Remove the bolts from the bottom of the fan motor.
Step 2. Feed the wire plug of the fan motor through the middle of the light plate. Install the light plate onto the motor and secure it by replacing and tightening the bolts.
Step 3. Connect the LED light kit to the light plate using its magnetic suction-cup bolts.
Step 4. Connect the wire plugs of the LED light kit to the wire plugs of the fan motor (blue to blue and white to white).
Step 5. Fit the shade onto the light plate, screwing it into place. Ensure it is firmly connected to avoid loosening during use.
Light Plate LED Light Kit Shade
Color Temperature Adjustment
The LED light has 3 different color settings: Warm White (3000K), Daylight (4000K), and Cool White (6000K). To adjust the light settings, 1. Press LIGHT on the remote control to turn on the LED light. 2. Hold LIGHT until the LED light turns off. 3. Hold LIGHT until the LED light turns on again with the next color temperature in order. Repeat these steps to cycle through the 3 color temperatures.
7
Remote Control Operation
Install the remote control holder onto any wall or suitable flat surface using two mounting screws/bolts.
Key
Function
LOW Starts the fan at low speed
MED Starts the fan at medium speed
HI Starts the fan at high speed
STOP Stops the fan
LIGHT Turns the light on or off
1H Runs the fan for 1 hour and then turns it off
2H Runs the fan for 2 hours and then turns it off
4H Runs the fan for 4 hours and then turns it off
R/F Reverses the fan’s direction
DO NOT press R/F while the fan is turning. Wait for it to stop completely before changing the direction of its rotation.
This remote operates with a range of 30 feet (10 m). It uses 2 1.5V AAA batteries (not included). If the remote will not be used for a prolonged period, it is recommended to remove the batteries for better service life.
8
Troubleshooting
Potential Problems Fan blades don’t rotate
Fan is too noisy Fan wobbles during use
Common Solutions
Check fuses and/or circuit breakers and reset if needed.
Cut off power to the fan and check its internal electrical connections.
Replace the remote control’s batteries.
Check that the fan cover is correctly placed and no screws interfere with the movement of the blades.
Contact customer service to replace a faulty remote control.
Check that all fasteners are well tightened.
Ensure the canopy housing has a short distance between itself and the ceiling.
Upon initial installation, allow 24 hours of use for the machine to break itself in.
Cut off power to the fan and check that the wire nut connections are not rubbing against one another or the inner housing.
If you have installed a solid-state variable-speed control, cut off power to the fan and disconnect this control from the device. See if using the remote resolves the problem, which can be caused by erratic signals from such controls.
Check that all fasteners are well tightened.
Use the provided balance kit to adjust the blades if their tips are found to be an unequal distance from the ceiling while well fastened.
Exchange the position of the various blades.
Again, do not bend the blades during any of these procedures.
9
Contact Us
Thank you for choosing our products! If you have any questions or comments, contact us at [email protected] and we’ll resolve your issue ASAP!
For a .pdf copy of the latest version of these instructions, use the appropriate app on your smartphone to scan the QR code to the right.
10
CFN-1105-00 Rev. 21 Apr. 2022
