Circa Basin Set
Product Information:
The product is called Circa Basin Set. It includes various
components such as Set Screw, Handle Body, Locking Sleeve, Fibre
Washer, Ceramic Spindle Cartridge, O Ring, Outlet Flange, Basin
Body Locknut, Locking Screw, Plastic Washer, and Breech. The
product has a maximum thickness of 28 mm and the O Ring for the
spindle has a diameter of 60 mm. The outlet flange is labeled
“Front”. There are different product codes available for different
variations of the basin set.
Product Usage Instructions:
- Ensure that the Fibre washer seals the Locking Flange to the
Basin Body. - Secure the product from under the bench using the locking
screws. - Raise the Basin Body assembly through the Mounting Surface to
tighten the Locking Sleeve. - Make sure to fully tighten the Locking Sleeve to the Basin Body
before tightening the assembly from underneath. - Tighten the Basin Body Locknut only after the Locking Sleeves
have been fully tightened. - If using a Tee piece, it should be breeched between basin
bodies. The length of the Tee piece may require cutting to
suit. - The product must be installed by a Licensed Plumber in
accordance with AS/NZS 3500:2003. - The recommended working water pressure is 300-500 kpa, and the
maximum water temperature is 65 deg.c.
Please note that for more detailed installation guidelines,
refer to Fig.1 in the user manual. Also, ensure compliance with
AS/NZS 3718:2005 for water efficiency and visit
www.waterrating.gov.au for the water rating information.
For any further information or assistance, please visit
sussextaps.com.au or contact Sussex Taps Pty Ltd.
Circa
Basin set
Set Screw
Handle Body
Locking Sleeve
Fibre Washer
Ceramic Spindle Cartridge
Maximum thickness 28 mm
O Ring 60 mm Spindle 32 – 35 mm
Outlet Flange will be labelled Front
installation
FRONT
0 Ring
Basin Body Locknut Basin Body
HOT
Locking Screw
Plastic Washer Outlet Locknut
Breech
NOTE: Tee piece is to be breeched between basin bodies. Length of Tee piece may require cutting to suit.
Important Note: Locking Sleeve must be fully tightened to the Basin Body prior to tightening the assembly from underneath.
Tighten Basin Body Locknut only after the Locking Sleeves have been fully tightened
COLD
Product code
RBS RBSHS
Basin set Basin sink set high
RBS-V RBSHS-V
Basin set – Vertex Basin sink set high – Vertex
Installation guidelines
– The Spindles will be supplied fitted into the Basin Bodies when supplied. – Determine the distance of the Basin/Hob holes and cut the breech to suit. – Place the Outlet Locknut and Plastic Washer over the outlet fitting of the Breech. – Align the breeched Basin Bodies and fit through the mounting surface. – Fit the Fibre Washer over the spindles. – Raise the assembled Basin Body through the mounted surface and fit the Locking Sleeves. – Fully tighten Locking Sleeves and ensure O Ring is intact before lowering assembly onto
mounting surface. (See Fig.1) – Working from underneath tighten the Basin Body Locknut to secure the assembly. – Outlet must be secured with the FRONT label facing the user. – Remove label after final installation. – Fit the Outlet to Breech and secure by tightening the locknut, ensure O Ring is intact. – Once all parts are tightened fit Handle and secure with Set Screw using Allen Key. – Connect Hot and Cold feed lines to the Basin Bodies. – Check all parts, fittings and connections for any water leaks.
Fig.1
Mounting Surface
The Fibre washer must seal the Locking Flange to the Basin Body.
Use locking screws to secure from under bench
Raise Basin Body assembly through the Mounting Surface to tighten Locking Sleeve. (As Shown)
sussextaps.com.au
AS/NZS 3718:2005 LIC. 20081
The more stars the more water efficient
WATER RATING
www.waterrating.gov.au
5.0 litres per minute
In accordance with AS/NZS 6400 Licence No. 0124 Sussex Taps Pty Ltd
Tapware is to be installed by a Licensed Plumber in accordance with AS/NZS 3500:2003 Recommended working water pressure 300-500 kpa. Maximum water temperature is 65 deg.c
Copyright © Sussex Taps.
