Crystorama 1110-ch-cl-mwp Traditional Crystal 10 Light Crystal Chandelier Instruction Manual

1110-CH-CL-MWP Traditional Crystal 10 Light Crystal Chandelier

Product Information:

This product is a lighting fixture manufactured by Crystorama.
It is model number 1110-CH-CL-MWP.

The fixture includes various crystal sets, such as square
crystals, beads, rosettes, and balls, in different sizes.

The electrical components of the fixture must be installed by a
licensed electrician in accordance with the National Electric Code
and local electrical codes.

The fixture requires 10 Candelabra Base Bulbs with a recommended
wattage of 40 Watts and a maximum wattage of 60 Watts. LED bulbs
are recommended for extended use.

The fixture is dry rated, meaning it is suitable for indoor use
only.

Installation instructions are provided below.

Product Usage Instructions:

  1. Place all the fixture parts on a soft cloth-covered platform
    before installation.
  2. Attach the bottom bowl, 2 metal washers, bottom bobeche, and
    metal washer in that order over the distributor box. Secure them
    with the finial.
  3. Attach the mounting bar onto the outlet box.
  4. Determine the desired hanging height and adjust the chain to
    the correct length.
  5. Raise the fixture up and make the wire connections. Attach the
    canopy over the mounting bar and secure it with the collar
    ring.
  6. Dress the crystals as illustrated.

Note: Ensure that the power is turned off before performing any
electrical connections or installations.

Warning: This product contains lead, which is
known to the State of California to cause cancer and/or birth
defects or reproductive harm. For more information, visit www.p65warnings.ca.gov.

LIGHTING THE WAY FOR SIXTY YEARS
ASSEMBLY INSTRUCTION MODEL #1110-CH-CL-MWP

Crystorama.com

WARNING:

A C

E
Attached to next bobeche.

D

O
C N
M

K J H G

B

O C
F P

K

I

N

L

M

Crystal Sets

A. 4 Sets. (1)24mm

B. 5 Sets. (5)14mm + (1)30mm + AS9-3″

C. 15 Sets. (1)Square

D. 5 Sets. (27)14mm

E. 10 Sets. (17)14mm

F. 10 Sets. G. 1 Piece. H. 4 Sets. I. 4 Sets.

(20)14mm (7)14mm + (2)Rosette + (1)60mm ball (3)14mm + AS9-3″ (5)14mm + AS9-3″

J. 4 Sets. (1)14mm + (1)28mm + AS9-3″

K. 5 Sets. (1)Ring of beads + (6)14mm + AS9-3″

L. 5 Sets. (1)Ring of beads + (8)14mm + (1)30mm + AS9-4″

M. 5 Sets. (1)Ring of beads + (1)30mm + AS9-4″

N. 5 Sets. (1)28mm + AS9-3.5″

O. 50 Sets. (1)14mm + AS9-2″

P. 5 Sets. (2)28mm + (1)24mm + AS9-4″

Electrical Danger Turn Power Off
All electrical components must be installed by a licensed electrician in accordance with the National Electric Code and the appropriate local electrical codes

You will need 10- Candelabra Base Bulb

40 Watts recommended 60 Watts Max.

USE LED BULBS FOR EXTENDED USE
The fixture is Dry rated

O HOW TO INSTALL:

C

Place the fixture parts on a soft

cloth-covered platform before

installation of fixture.

1. To install the 6″ & 12″arms, slightly loosen each screw on the metal plate. Pull a female plug through a hole in the upper metal plate. Connect the male plug at the end of the arms with the female plug that was just pulled. Push the end of the arm with the metal tab through the hole until stopped by the metal tab (this should also push the wires and plugs back inside the metal plate). Twist the metal tab counter-clock wise until both inserts lock onto the loose screws. Tighten the screw securing the arm in place. Repeat for all arms.

3. Place the bottom bowl, 2 metal washers, bottom bobeche, metal washer in that order, over the distributor box. Secure with the finial.

4. Attach the mounting bar onto the outlet box.

5. Decide the desired hanging height and adjust the chain to the correct length.

6. Raise the fixture up and do the wire connection. Attach the canopy over the mounting bar and secure with collar ring.
7. Dress the crystals as illustrated.

WARNING:This product can expose you to Lead,
which is known to the State of California to cause cancer and/or birth defects or reproductive harm.For more
information go to www.p65warnings.ca.gov

A B D G H
I J
K
L M
N P Q
R S
T U

LIGHTING THE WAY FOR SIXTY YEARS
ASSEMBLY INSTRUCTION MODEL #1110-CH-CL-MWP

Crystorama.com

Outlet Box C E
F
(Bulb not include)
O

Part Number
Part Numbers
A. (2)-Wire Connector B. (1)-Mounting Bar C. (1)-Lock Washer D. (1)-Hex Nut E. (1)-Nipple F. (1)-Canopy (W5″xH1″)-XSN1110CHCAN5IN G. (1)-Collar Ring H. (1)-Collar Loop
I. (1)-Chain (4mmx72″)-XSN1110CHCHA4MM
J. (1)-Center Column Kit Loop
K. (1)-Center Column Kit Top Bobeche ; Ø4″,4pin,24mm center hole. -XSN1110CHBOB4IN Top Bowl ; Ø6″ ; 10pin,13mm center hole. -XSN1110TODISH6IN Glass Vase; H8″ Glass ball ; Ø5″ Glass Vase ; H8″ Metal Cover ; H1.5″
L. (10)-PVC candle sleeve ; Ø7/8″, H4 1/8″. -XSN1110CDL4IN
M. (10)-Bobeche ; Ø5″ ; 5 pin, 24mm center hole. -XSN1110CHBOB5IN
N. (5)-6″ Arms with holder-XSN529CHARM6IN O. (5)-12″ Arms with holder-XSN500CHARM12IN P. (10)-Male Plug Q. (10)-Female Plug R. (1)-Distributor Box ; Ø5 1/2″ S. (1)-Bottom Bowl ; Ø6″,8 pin,13mm center hole.
-XSN1110CHBODISH6IN T. (3)-Metal washer U. (1)-Bottom Bobeche; Ø4″,4 pin,24mm center hole.
-XSN1110CHBOB4PN
V. (1)-Finial-XSN1110CHFIN

T V
Female Plug

Arm with Metal tab

Male Plug

Plate

Screws

References

Documents / Resouces

Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.


Related Manuals