1155-PB-CL-MWP Traditional Crystal 15 Light Chandelier
Product Information: – Model: 1155-PB-CL-MWP – Brand: Crystorama –
Website: Crystorama.com – Fixture Type: Chandelier – Power Source:
Electric – Bulb Type: Candelabra Base Bulb – Bulb Wattage: 40 Watts
recommended, 60 Watts Max – Usage: Damp rated – Assembly Required:
Yes – Warranty: Not specified Product Usage Instructions: 1. Before
installation, place all fixture parts on a soft cloth-covered
platform. 2. Install the upper arms by slightly loosening each one
and attaching them to the fixture. 3. Repeat step 2 for the lower
arms. 4. Place the bottom bowl, metal washer, check ring, coupling,
glass vase, check ring, metal washer, bottom bobeche, metal washer,
in that order, over the distributor box-2. Secure with the finial.
5. Screw the center column kit 1 onto the center column kit 2. 6.
Attach the mounting bar onto the outlet box. 7. Decide the desired
hanging height and adjust the chain to the correct length. 8. Raise
the fixture up and make the wire connection. 9. Attach the canopy
over the mounting bar and secure it with the collar ring. 10. Dress
the crystals as illustrated. Safety Precautions: – Turn off power
before installing any electrical components. – All electrical
components must be installed by a licensed electrician in
accordance with the National Electric Code and local electrical
codes. Important Notes: – Use LED bulbs for extended use. – This
product is damp rated, suitable for use in damp environments. –
This product contains lead, which is known to the State of
California to cause cancer and/or birth defects or reproductive
harm. For more information, visit www.p65warnings.ca.gov. Note: The
user manual does not provide detailed information about specific
part numbers and their corresponding usage. For detailed
instructions on specific parts, please refer to the product
packaging or contact the manufacturer directly.
LIGHTING THE WAY FOR SIXTY YEARS
ASSEMBLY INSTRUCTION MODEL #1155-PB-CL-MWP
Crystorama.com
WARNING:
Alternating E & J
117 3/4″ 43 3/4″
32″
Crystal Sets
A. 25 Sets. B. 5 Sets. C. 1 Piece. D. 60 Sets.
(2)14mm + (1) Square + AS9-2.5″ (2)14mm + AS9-2″ (4)14mm + AS8-50mm Ball (1)14mm + AS9-2″
E. 5 Sets. (5)14mm + AS9-2.5″
F. 10 Sets. G. 5 Sets. H. 10 Sets. I. 10 Sets.
(3)14mm + AS9-2.5″ (11)14mm (10)14mm (6)14mm
J. 5 Sets. (17)14mm
K. 10 Sets. (7)14mm + AS9-2.5″
Electrical Danger Turn Power Off
All electrical components must be
installed by a licensed electrician
in accordance with the National
Electric Code and the appropriate
local electrical codes
You will need 15- Candelabra Base Bulb
40 Watts recommended 60 Watts Max.
USE LED BULBS FOR EXTENDED USE
The fixture is Damp rated
HOW TO INSTALL:
Place the fixture parts on a soft cloth-covered platform before installation of fixture. 1. To install the upper arms, slightly loosen each
screw on the metal plate. Pull a female plug through a hole in the upper metal plate. Connect the male plug at the end of the upper arm with the female plug that was just pulled. Push the end of the arm with the metal tab through the hole until stopped by the metal tab (this should also push the wires and plugs back inside the metal plate). Twist the metal tab counter-clock wise until both inserts lock onto the loose screws. Tighten the screw securing the arm in place. Repeat for all upper arms.
2. Repeat Step1 for the lower arms.
3. Place the bottom bowl,metal washer, check ring,coupling,Glass vase, check ring, metal washer, bottom bobeche, metal washer, in that order, over the distributor box-2. Secure with the Finial.
4. Screw the Center column kit 1 onto the center column kit 2.
5. Attach the mounting bar onto the outlet box. 6. Decide the desired hanging height and
adjust the chain to the correct length.
7. Raise the fixture up and do the wire connection. Attach the canopy over the mounting bar and secure with collar ring.
8. Dress the crystals as illustrated.
WARNING:This product can expose you to Lead,
which is known to the State of California to cause cancer and/or birth defects or reproductive harm.For more information go to www.p65warnings.ca.gov
C D
E F
G
L H
I
J
O P
Q
O O
K N
R S
P T
U
LIGHTING THE WAY FOR SIXTY YEARS
ASSEMBLY INSTRUCTION MODEL #1155-PB-CL-MWP
Crystorama.com
Outlet Box A
B
M
Part Number
Part Numbers
A. (1)-Mounting hardware Wire connector x 2. Mounting bar x 1. Lock washer x 1. Hex Nut x 1. Nipple x 1. Screw x 2.
B. (1)-Canopy (W5″xH1″)-XSN1155PBCAN5IN C. (1)-Collar Ring D. (1)-Collar Loop-XSN1155PBLOOP1
E. (1)-Chain (4mmx72″)-XSN1155PBCHA4MM
F. (1)-Center Column Kit Loop-XSN1155PBLOOP2
G. (1)-Center Column Kit 1 Top Bowl ; Ø6″,10pin,11mm center hole. Glass Vase; H8″ Top Bobeche ; Ø4″, no pin,24mm center hole. -XSN1155BOB4IN Glass Vase x 1 ; H6″ Metal Cover ; H1.5″
H. (5)-6″upper Arms with holder-XSN500GDARM6INKD
I. (1)-Center Column Kit 2 Glass Bowl ; Ø6″,10 pin,11mm center hole. Distributor Box-1; Ø4 7/8 ” ; 11mm center hole ; with female plug. Glass Vase; H8″ Distributor Box-2; Ø7 1/8″, 11mm center hole ; with female plug.
J. (10)-12″ lower Arms with holder-XSN500GDARM12INKD
K. (15)-Male Plug
L. (15)-Bobeche; Ø4″,4 pin,24mm center hole. -XSN1155PBBOB4PN
M. (15)-PVC Candle Sleeve N. (1)-Bottom Bowl ; Ø8″,10 pin,11mm center hole. O. (3)-Metal washer P. (2)-Check Ring Q. (1)-Coupling
R. (1)-Glass Vase; H6″
S. (1)-Thread pipe
T. (1)-Bottom Bobeche; Ø4″,5 pin,24mm center hole. -XSN1155PBBOB5PN
U. (1)-Finial-XSN1155PBFIN
Female Plug
Arm with Metal tab
Male Plug
Plate
Screws
Crystorama Lighting
p65warnings.ca.gov
