Carbatec Ct-sr-g Seam Ripper Kit Instructions

CT-SR-G Seam Ripper Kit

Product Information:

The Needle Threader Kit (CT-NT-CH) and Seam Ripper Kit (CT-SR-G)
are woodworking kits manufactured by Carbatec Pty Ltd. The kits
include all the necessary tools and accessories to create needle
threaders and seam rippers.

The barrels of the kits are made out of turned wood or acrylic
blanks, providing durability and a smooth finish.

The Needle Threader Kit (CT-NT-CH) includes a clip assembly and
relevant tip assembly to securely hold the thread. It is designed
to make threading needles easier and more efficient.

The Seam Ripper Kit (CT-SR-G) includes a clip assembly and
relevant tip assembly that can be reversed for safe storage. It is
designed to remove stitches and seams without damaging the
fabric.

Product Usage Instructions:

A. Required Tools and Accessories:

1. Turned wood or acrylic blanks
2. Headstock
3. Spacer bushings
4. Tube
5. Mandrel
6. End bushing
7. Knurled nut
8. Live centre

B. Preparing the Blank:

1. Cut a blank that is at least 3/4 inch (or larger) in length,
   matching the brass tubes’ length (add 1/16 inch for squaring
   off).
2. Drill an 8mm hole through the center of the blank.
3. Spread glue over the tube.
4. Insert the tubes into the blank with a twisting motion to
   evenly distribute the glue inside.
5. Center the tubes lengthwise inside the blank.
6. After the glue has dried, trim the ends of the blank flush to
   the tube.

C. Turning the Blank:

1. Place the bushings and blank onto the mandrel according to
   Figure 1.
2. Thread on the knurled nut and hand tighten it on the mandrel to
   hold the components in place.
3. Slide the tailstock to the mandrel shaft and lock it in place
   (do not overtighten to avoid damage or bending of the
   mandrel).
4. Using turning chisels, turn the handle ends down until they are
   flush with the bushings, gradually increasing grades of sandpaper
   for a smooth finish.
5. Apply polish or another finish to complete the blank.

D. Assembly:

1. Press the clip assembly to one end of the tube.
2. Slide the relevant tip assembly in and out of both ends to
   ensure a secure fit.
3. When not in use, reverse the tip assembly to safely store the
   tool.

If you have any further questions or need assistance, please
contact Carbatec Pty Ltd at 1800 658 111 (Australia) or Carbatec
New Zealand Ltd at 0800 444 329 (New Zealand).

Needle Threader Kit – CT-NT-CH Seam Ripper Kit – CT-SR-G INSTRUCTIONS

CT-NT-CH

CT-SR-G

A.REQUIRED TOOLS AND ACCESSORIES

· 7 mm pen mandrel (MAND-92) · 8 mm Drill Bit (BPD-8MM-PRC) · Barrel Trimmer (PKTRIMKIT) · 2 pcs Bushings Set (BUSH-SRNT)

· 2 part epoxy glue or CA super glue (cyanoacrylate)
· Wood or acrylic blank, minimum size 3/4″ square
· Sanding and finishing supplies

The barrels are made out of turned wood or acrylic blanks.

HEADSTOCK

SPACER BUSHINGS

BLANK

TUBE

SPACER BUSHINGS

MANDREL

END BUSHING

END BUSHING

KNURLED NUT

LIVE CENTRE

Fig. 1

B. PREPARING THE BLANK
1. Cut a 3/4″ or larger blank, to the length of the brass tubes (add 1/16″ for squaring off).
2. Drill an 8mm hole through the centre of the blank. 3. Spread glue over the tube. 4. Insert the tubes into the blank with a twisting motion to spread the glue evenly inside. 5. Centre the tubes lengthwise inside the blank. 6. When the glue is dry, trim the ends of the blank flush to the tube.

Call 1800 658 111 (Australia) C A R B AT E C.C O M . AU

Call 0800 444 329 (New Zealand) C A R B AT E C .C O. N Z

NEEDLE THREADER KIT & SEAM RIPPER KIT
C. TURNING THE BLANK
1. Place the bushings and blank onto the mandrel according to figure 1. 2. Thread on the knurled nut and hand tighten on the mandrel to hold components
in place. 3. Slide the tailstock to the mandrel shaft and lock in place (do not overtighten or it
could damage or bend the mandrel). 4. Turn the handle ends down, flush with the bushings using turning chisels,
finishing by gradually increasing grades of sandpaper. 5. Finish the blank by applying polish or other finish.
D. ASSEMBLY
1. Press the clip assembly to one end of the tube. 2. Slide the relevant tip assembly in and out of both ends to assure a secure fit. 3. When not in use, reverse tip assembly to safely store the tool.

2

Needle Threader Kit CT-NT-CH

Fig. 2

Seam Ripper Kit CT-SR-G

Carbatec Pty Ltd 128 Ingleston Road, Wakerley, Queensland, Australia 1800 658 111 – CARBATEC.COM.AU

Carbatec New Zealand Ltd 110 Harris Rd, East Tamaki, Auckland 2013, New Zealand 0800 444 329 – CARBATEC.CO.NZ

References

• Carbatec NZ
• Carbatec - The Home of Woodworking