Infineon Cysbsyskit-dev-01 Rapid Iot Connect Developer Kit User Guide

CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit

Product Information:

The CYSBSYSKIT-DEV-01 Rapid IoT Connect Developer Kit is a kit
that contains a CYSBSYS-RP01 system-on-module and an OPTIGATM Trust
M security controller. The kit includes a board with features like
a chip antenna, user button, 17.2032-MHz ECO, JTAG header, reset
button, battery connector, 3.3-V regulator, Micro-B USB connector,
thermistor, KitProg3 programming mode selection button, and a super
capacitor (footprint only; not populated on the board). The kit is
sensitive to ESD and should be held only by its stack-up headers.
To avoid damage, it should be placed on a grounded, static-free
surface and not slid over any surface.

Product Usage:

1. Ensure that you have a JST connector (Adafruit 2750 or
   similar).
2. Connect the board to a PC using the USB cable provided and wait
   for the driver installation to complete.
3. Verify that the battery is connected and charging by checking
   that the corresponding LED is glowing.
4. Open a UART terminal software and connect it to the kit.
5. Press the reset button (RST_BTN) to reset the device.
6. You should see the output of the pre-loaded application (Wi-Fi
   scan) on the serial terminal.
7. Visit the kit website for information on Quick IoT Experience
   and code examples supported for this kit and kit
   documentation.

CYSBSYSKIT-DEV-01 Pinout:

The table below shows the pinout for the CYSBSYSKIT-DEV-01
board:

The USB-UART COM port setup for the serial terminal should be
configured with a stop bit of 1 bit and no flow control.

UM_2203_PL32_2204_092120

Quick start guide
Rapid IoT Connect developer kit with CYSBSYS-RP01 system-on-module and OPTIGATM Trust M security controller
CYSBSYSKIT-DEV-01
CYSBSYSKIT-DEV-01 board top view CYSBSYS-RP01 module
Chip antenna (A1)

User button (USR_BTN)

17.2032-MHz ECO (Y1) JTAG header*

Header compatible with Adafruit Feather (J1)
Reset button (RST)

Header compatible with Adafruit Feather (J5)

Battery connector (J3)

3.3-V regulator (TPS7A2533DRVR – U15)

KitProg3 status LED (Yellow ­ LED3)

Power LED (Blue ­ LED4)

User LED (Red ­ LED2)

Charging indicator LED (Yellow ­ LED5)

Kit contents

Micro-B USB connector (J4)

· CYSBSYSKIT-DEV-01 board

www.infineon.com/CYSBSYSKIT-DEV-01

Quick start guide

CYSBSYSKIT-DEV-01 board bottom view

Thermistor (RT1)

Infineon 512-Mbit serial NOR flash (S25FL512S ­ U3)

KitProg3 programming mode
selection button (KP3_MODE)
1.8-V regulator (TPS7A2518DRVR ­ U14)

OPTIGATM Trust M (U7)
Super capacitor*
KitProg3 (PSoCTM 5LP) programmer and debugger (CY8C5868LTI-LP039 ­ U2)
Li-Po battery charger IC (BQ24074RGTT ­ U10)

3.6-V regulator (RT6158AWSC ­ U11)
* Footprint only; not populated on the board.
IMPORTANT: CYSBSYSKIT-DEV-01 Rapid IoT connect developer kit is sensitive to ESD. Hold the board only by its stack-up headers. After removing the board from its box, place it on a grounded, static-free surface. Use a conductive foam pad, if available. Do not slide the board over any surface.

Quick start guide

Before you start
1. Ensure that you have the following:
· PC with USB port · UART terminal software such as Tera Term
or Minicom · USB cable with Micro-B connector at one end · (Optional) 3.7-V, 350-mAh Li-Po battery with
JST connector (Adafruit 2750 or similar)
2. With the USB cable, connect the board to the PC and wait for the driver installation to complete.
3. Verify that the following LEDs glow:
· Power LED (Blue ­ LED4) · KitProg3 Status LED (Yellow ­ LED3) · Charging LED (Yellow ­ LED5) if the Li-Po
battery is connected and charging
Connect the kit with the UART terminal software 1. Open the UART terminal software and connect
the kit’s USB-UART COM port with the following settings: · Baud rate: 115200, Data: 8 bit, Parity: None,
Stop bit: 1 bit, Flow control: None
2. Press the reset button (RST_BTN) to reset the device. You should see the output of the pre-loaded application (Wi-Fi scan) on the serial terminal.
Next Steps
Visit the kit website for information on Quick IoT Experience and code examples supported for this kit and kit documentation.

Kit with pin mapping

P6_1/SDA P6_0/SCL P8_4/IO5 P9_7/IO6 P9_4/IO9 P9_3/IO10 P9_2/IO11 P9_1/IO12 P9_0/IO13 5.0V EN VBAT

P5_3/CS P6_5/TX P6_4/RX P5_1/MISO P5_0/MOSI P5_2/SCK P10_5/A5 P10_4/A4 P10_3/A3 P10_2/A2 P10_1/A1 P10_0/A0 NC GND 3.3V XRES

USB-UART COM port setup

Serial terminal

Quick start guide

Table 1 CYSBSYSKIT-DEV-01 pinout

Header Primary onboard function

PSoCTM 6 MCU pin

FeatherWings compatibility

Connection details

J1.1 J1.2 J1.3 J1.4 J1.5 J1.6 J1.7 J1.8 J1.9 J1.10 J1.11 J1.12 J5.1

VBAT EN
VBUS GPIO GPIO GPIO GPIO GPIO GPIO GPIO I2C SCL I2C SDA XRES

­ ­ ­ P9_0 P9_1 P9_2 P9_3 P9_4 P9_7 P8_4 P6_0 P6_1 XRES

­ ­ ­ GPIO13 GPIO12 GPIO11 GPIO10 GPIO9 GPIO6 GPIO5 SCL SDA XRES

Li-Po battery supply Input to turn OFF power regulators
USB power ­ ­ ­ ­ ­ ­ ­
Connected to KitProg3 Connected to KitProg3
­

J5.2
J5.3 J5.4 J5.5 J5.6 J5.7 J5.8 J5.9 J5.10 J5.11 J5.12 J5.13 J5.14 J5.15 J5.16

3.3 V

VDDA, VDDIO VCC

NC GND Analog GPIO Analog GPIO Analog GPIO Analog GPIO Analog GPIO Analog GPIO SPI Clock SPI MOSI SPI MISO UART RX UART TX SPI CS

­ ­ P10_0 P10_1 P10_2 P10_3 P10_4 P10_5 P5_2 P5_0 P5_1 P6_4 P6_5 P5_3

­ GND A0 A1 A2 A3 A4 A5 SCK MOSI MISO RX TX GPIO14

Analog voltage for PSoCTM 6 MCU (in the Rapid IoT Connect system-on-module)
Not connected ­ ­ ­ ­ ­ ­ ­
SPI clock SPI Master Out / Slave In (MOSI) SPI Master In / Slave Out (MISO
Connected to KitProg3 Connected to KitProg3
SPI Chip Select

Document number: 002-30996 Rev. *B Date: 03 / 2022

All rights reserved. © 2022 Infineon Technologies AG