Contents hide

2 Product Information: 22k Air Angle Die Grinder

2.2 Setup

2.3 Operation

2.4 Maintenance

2.5 Parts List and Diagram

2.6 Warranty

2.6.1 Documents / Resources

58909 Air Angle Die Grinder

Product Information: 22k Air Angle Die Grinder

The 22k Air Angle Die Grinder is a tool that can be used for
various grinding and cutting applications. It is designed to
operate at a maximum speed of 22,000 RPM and comes with a safety
alert symbol that is used to alert you to potential personal injury
hazards. The grinder is equipped with features that reduce the
risks of electric shock, fire, and injury to persons.

Specifications

Maximum speed: 22,000 RPM
Designed for grinding and cutting applications
Safety alert symbol included

Setup

When unpacking the product, make sure that it is intact and
undamaged. If any parts are missing or broken, please call
1-888-866-5797 as soon as possible. Tools required for assembly and
service may not be included. Read the manual before using the
product. Failure to do so can result in serious injury.

Operation

Keep the work area clean and well lighted. Do not operate the
tool in explosive atmospheres, such as in the presence of flammable
liquids, gases, or dust. Keep bystanders, children, and visitors
away while operating the tool. Stay alert while using the tool and
use common sense. Do not use the tool while tired or under the
influence of drugs, alcohol, or medication. Dress properly and do
not wear loose clothing or jewelry. Keep hair, clothing, and gloves
away from moving parts.

Maintenance

For technical questions, please call 1-888-866-5797. Maintain
the tool by following the inspection, maintenance, and cleaning
procedures outlined in the manual. Failure to do so can result in
serious injury.

Parts List and Diagram

A parts list and diagram are included in the manual for
reference. Write the product’s serial number in the back of the
manual near the assembly diagram (or month and year of purchase if
product has no number).

Warranty

The product comes with a warranty. Refer to the manual for
details.

View Fullscreen

Owner’s Manual & Safety Instructions

Save This Manual Keep this manual for the safety warnings and precautions, assembly,

operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the

back of the manual near the assembly diagram (or month and year of purchase if product has no number).

Keep this manual and the receipt in a safe and dry place for future reference.

22k

Air Angle Die Grinder

Visit our website at: http://www.harborfreight.com Email our technical support at: [email protected]

58909

When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken,
please call 1-888-866-5797 as soon as possible.
Copyright© 2021 by Harbor Freight Tools®. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.

Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANUAL.

SaFEty

SEtup

table of contents

Safety …………………………………………………. 2 Specifications ………………………………………. 6 Setup ………………………………………………….. 7 Operation……………………………………………. 10

Maintenance ……………………………………….. 12 Parts List and Diagram …………………………. 14 Warranty …………………………………………….. 16

WarninG SyMBOLS anD DEFinitiOnS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages
that follow this symbol to avoid possible injury or death. Indicates a hazardous situation which, if not avoided,
will result in death or serious injury. Indicates a hazardous situation which, if not avoided,
could result in death or serious injury. Indicates a hazardous situation which, if not avoided,
could result in minor or moderate injury.
Addresses practices not related to personal injury.

iMpOrtant SaFEty inStructiOnS
inStructiOnS pErtaininG tO a riSK OF FirE, ELEctric SHOcK, Or inJury tO pErSOnS
WarninG When using tools, basic precautions should always be followed, including the following:

General
to reduce the risks of electric shock, fire, and injury to persons, read all the instructions before using the tool.

Work area
1. Keep the work area clean and well lighted. Cluttered benches and dark areas increase the risks of electric shock, fire, and injury to persons.
2. Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The tool is able to create sparks resulting in the ignition of the dust or fumes.

3. Keep bystanders, children, and visitors away while operating the tool. Distractions are able to result in the loss of control of the tool.

OpEratiOn

MaintEnancE

Page 2

For technical questions, please call 1-888-866-5797.

Item 58909

SaFEty

SEtup

personal Safety
1. Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool increases the risk of injury to persons.
2. Dress properly. Do not wear loose clothing or jewelry. contain long hair. Keep hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair increases the risk of injury to persons as a result of being caught in moving parts.
3. avoid unintentional starting. Be sure the switch is off before connecting to the air supply. Do not carry the tool with your finger on the switch or connect the tool to the air supply with the switch on.
4. remove adjusting keys and wrenches before turning the tool on. A wrench or a key that is left attached to a rotating part of the tool increases the risk of personal injury.
5. Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in unexpected situations.
tool use and care
1. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against the body is unstable and is able to lead to loss of control.
2. Do not force the tool. Use the correct tool for the application. The correct tool will do the job better and safer at the rate for which the tool is designed.
3. Do not use the tool if the switch does not turn the tool on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.

use safety equipment.

A dust mask, non-skid safety

shoes and a hard hat must be

used for the applicable conditions.

always wear eye protection.

Wear ANSI-approved

safety goggles.

always wear hearing protection

when using the tool.

Prolonged exposure to high

intensity noise is able to cause

hearing loss.

9. risk of Electric Shock. this tool is not provided with an insulated gripping surface. Contact with a live wire will also make exposed metal parts of the tool live and shock the operator.

10. avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded.

11. Explore the workpiece to avoid contact with hidden wiring. Thoroughly investigate the workpiece for possible hidden wiring before performing work. Contact with live wiring will shock the operator.

4. Disconnect the tool from the air source before making any adjustments, changing accessories, or storing the tool. Such preventive safety measures reduce the risk of starting the tool unintentionally. Turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position before leaving the work area.
5. Store the tool when it is idle out of reach of children and other untrained persons. A tool is dangerous in the hands of untrained users.
6. Maintain the tool with care. Keep a cutting tool sharp and clean. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control.

OpEratiOn

MaintEnancE

Item 58909

For technical questions, please call 1-888-866-5797.

Page 3

SaFEty

7. check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if the tool is damaged.

8. use only accessories that are identified by the manufacturer for the specific tool model. Use of an accessory not intended for use with the specific tool model, increases the risk of injury to persons.

Service
1. Tool service must be performed only by qualified repair personnel.
2. When servicing a tool, use only identical replacement parts. use only authorized parts.

3. use only the lubricants supplied with the tool or specified by the manufacturer.

air Source

never connect to an air source

that is capable of exceeding

200 psi. Over pressurizing the

tool may cause bursting,

abnormal operation, breakage of the tool or

serious injury to persons. Use only clean,

dry, regulated compressed air at the rated

pressure or within the rated pressure range

as marked on the tool. Always verify prior to

using the tool that the air source has been

adjusted to the rated air pressure or within

the rated air-pressure range.

2. Never use oxygen, carbon dioxide, combustible gases or any bottled gas as an air source for the tool. Such gases are capable of explosion and serious injury to persons.

SaVE tHESE inStructiOnS.

SEtup

OpEratiOn

MaintEnancE

Page 4

For technical questions, please call 1-888-866-5797.

Item 58909

SaFEty

SEtup

Symbols and Specific Safety instructions

Symbol Definitions

Symbol property or statement

rpM

Revolutions or reciprocation per minute

pSi

Pounds per square inch of pressure

ft-lb Foot-pounds of torque

cFM Cubic Feet per Minute flow

npt National pipe thread, tapered

Symbol

property or statement
WARNING marking concerning Risk of Eye Injury. Wear ANSI-approved eye protection.
WARNING marking concerning Risk of Hearing Loss. Wear hearing protection.
WARNING marking concerning Risk of Respiratory Injury. Wear NIOSH-approved dust mask/respirator.
WARNING marking concerning Risk of Explosion.

Specific Safety instructions
1. The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
2. Only use with accessories rated to handle the forces exerted by this tool during operation. Other accessories not designed for the forces generated may break and forcefully launch pieces.
Vibration precautions
This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:

3. Attach all accessories properly to the tool before connecting the air supply. A loose accessory may detach or break during operation.
4. Obey the manual for the air compressor used to power this tool.
5. Install an in-line shutoff valve to allow immediate control over the air supply in an emergency, even if a hose is ruptured.
6. Use this tool with both hands only. Using tools with only one hand can result in loss of control.
7. Do not lay the tool down until it has come to a complete stop. Moving parts can grab the surface and pull the tool out of your control.
1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders,

OpEratiOn

MaintEnancE

Item 58909

For technical questions, please call 1-888-866-5797.

Page 5

SaFEty

diabetes, or Raynaud’s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.

4. Use tools with the lowest vibration when there is a choice.
5. Include vibration-free periods each day of work.

2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.

6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work.

3. Wear suitable gloves to reduce the vibration effects on the user.

7. To reduce vibration, maintain tool as explained in this manual. If abnormal vibration occurs, stop immediately.

SaVE tHESE inStructiOnS.

Functional Description

Specifications

Speed Collett Size:
Max Air Consumption (No Load)
Air Consumption (At Load) Air Inlet: Recommended Hose Size: Operating Pressure:

20,000 RPM 1/8 or 1/4
19 SCFM (2.9 CFM @ 90 PSI)
18 SCFM (2.8 CFM @ 90 PSI) 1/4 NPT
3/8
90 PSI

* Rated speed at stated maximum air pressure. Excess air pressure is hazardous and may cause the tool to exceed stated rated speed.

components and controls

SEtup

OpEratiOn

MaintEnancE

Page 6

air inlet

Spindle

throttle

collet nut

collet (not visible)

Safety Lock

For technical questions, please call 1-888-866-5797.

Item 58909

SaFEty

initial tool Set up/assembly
read the EntirE iMpOrtant SaFEty inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
note: This air tool may be shipped with a protective plug covering the air inlet. Remove this plug before set up.
air Supply

SEtup

OpEratiOn

tO prEVEnt SEriOuS inJury FrOM EXpLOSiOn: use only clean, dry, regulated, compressed air to power this tool. Do not use oxygen, carbon dioxide, combustible gases, or any other bottled gas as a power source for this tool.

1. Incorporate a filter, regulator with pressure gauge, oiler, in-line shutoff valve, and quick coupler for best service, as shown on Figure A on page 8 and Figure B on page 9. an in-line shutoff ball valve is an important safety device because it controls the air supply even if the air hose is ruptured. the shutoff valve should be a ball valve because it can be closed quickly.
note: If an automatic oiler system is not used, add a few drops of Pneumatic Tool Oil to the airline connection before operation. Add a few more drops after each hour of continual use.
2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool. Other components, such as a coupler plug and quick coupler, will make operation more efficient, but are not required.
WarninG! tO prEVEnt SEriOuS inJury FrOM acciDEntaL OpEratiOn: Do not install a female quick coupler on the tool. Such a coupler contains an air valve that will allow the air tool to retain pressure and operate accidentally after the air supply is disconnected.
note: Air flow, and therefore tool performance, can be hindered by undersized air supply components. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working.

3. Turn the tool’s throttle or switch to the off position; refer to Operation section for description of controls.
4. Close the in-line shutoff valve between the compressor and the tool.
5. Turn on the air compressor according to the manufacturer’s directions and allow it to build up pressure until it cycles off.
6. Adjust the air compressor’s output regulator so that the air output is enough to properly power the tool, but the output will not exceed the tool’s maximum air pressure at any time. Adjust the pressure gradually, while checking the air output gauge to set the right pressure range.
7. Inspect the air connections for leaks. Repair any leaks found.
8. If the tool will not be used at this time, turn off and detach the air supply, safely discharge any residual air pressure, and release the throttle and/or turn the switch to its off position to prevent accidental operation.
note: Residual air pressure should not be present after the tool is disconnected from the air supply. However, it is a good safety measure to attempt to discharge the tool in a safe fashion after disconnecting to ensure that the tool is disconnected and not powered.

Item 58909

For technical questions, please call 1-888-866-5797.

Page 7

MaintEnancE

SaFEty

SEtup

OpEratiOn

MaintEnancE

Page 8

Figure a: portable air Supply Setup

Lubricated Tools

BC D

For technical questions, please call 1-888-866-5797.

Non-lubricated

Tools

Description
A Air Hose B Filter C Regulator D Lubricator (optional) E Coupler and Plug F Leader Hose (optional) G Air Cleaner / Dryer (optional) H Air Adjusting Valve (optional)

Function
Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapor from damaging workpiece For fine tuning airflow at tool

Item 58909

Figure B: Stationary air Supply Setup

Slope

Lubricated

Tools
C

CD E

For technical questions, please call 1-888-866-5797.

Description
A Vibration Pads B Anchor Bolts C Ball Valve D Isolation Hose E Main Air Line – 3/4 minimum recommended F Ball Valve G Branch Air Line -1/2 minimum recommended H Air Hose I Filter J Regulator K Lubricator (optional) L Coupler and Plug M Leader Hose (optional) N Air Cleaner / Dryer (optional) O Air Adjusting Valve (optional)

Non-lubricated Tools

Function
For noise and vibration reduction Secures air compressor in place Isolates sections of system for maintenance For vibration reduction Distributes air to branch lines To drain moisture from system Brings air to point of use Connects air to tool Prevents dirt and condensation from damaging tool or workpiece Adjusts air pressure to tool For air tool lubrication Provides quick connection and release Increases coupler life Prevents water vapor from damaging workpiece For fine tuning airflow at tool

Page 9

MaintEnancE

OpEratiOn

SEtup

SaFEty

Operating instructions
read the EntirE iMpOrtant SaFEty inFOrMatiOn section at the beginning of this manual including all text under subheadings therein before set up or use of this product. inspect tool before use, looking for damaged, loose, and missing parts. if any problems are found, do not use tool until repaired.
tool Set up

tO prEVEnt SEriOuS inJury: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. improper adjustment can result in tool failure or other serious hazards.

1. Use the Small Wrench to hold the Spindle in place and, at the same time, loosen the Collet Nut with the Large Wrench.

Large Wrench

collet nut

collet

2. Insert the accessory (sold separately) into the Collet opening. the accessory must be rated to at least the maximum speed of the Die Grinder.
3. Tighten the Collet Nut firmly.

WarninG! tO prEVEnt SEriOuS inJury: Do not use with cutoff wheels, saws or any attachment that requires a safety guard. this tool does not have a safety guard.

SEtup

OpEratiOn

MaintEnancE

Spindle
Small Wrench

Workpiece and Work area Set up

1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury.
2. Route the air hose along a safe route to reach the work area without creating a tripping hazard or exposing the hose to possible damage. The hose must be long enough to reach the work area with enough extra length to allow free movement while working.

3. Secure loose workpieces using a vise or clamps (not included) to prevent movement while working.
4. There must not be hazardous objects (such as utility lines or foreign objects) nearby that will present a hazard while working.

Page 10

For technical questions, please call 1-888-866-5797.

Item 58909

SaFEty

General Operating instructions

1. If an automatic oiler is not used, add a few drops of Pneumatic Tool Oil into the Air Inlet before every use.
2. Release the Throttle.
3. Connect air supply hose to Air Inlet. Turn on air compressor and set its regulator to the maximum 90 PSI.
cautiOn! Grip the tool firmly with both hands.
4. Slide the safety forward and press down on the Throttle.
note: The Die Grinder’s speed is variable. Vary the pressure placed on the Throttle and/ or adjust the Air Control Knob to vary the speed of the tool. Use only enough speed as needed to grind the work piece.
note: Keep the accessory off the surface of the work piece until it reaches operating speed.
5. Slowly and carefully place the accessory onto the surface of the work piece.

6. Keep steady pressure, but do not force the tool. Use only enough pressure to do the job properly.
7. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool.
cautiOn! tO prEVEnt inJury FrOM tOOL Or attacHMEnt FaiLurE: Do not exceed the tool’s maximum air pressure rating of 90 pSi. If the tool still does not have sufficient force at maximum pressure and sufficient airflow, then a larger tool may be required.
8. Once work is completed, release the Throttle.
9. To prevent accidents, detach the air supply and safely discharge any residual air pressure in the tool after use. Clean external surfaces of the tool with clean, dry cloth, and apply a thin coat of tool oil. Then store the tool indoors out of children’s reach.

SEtup

OpEratiOn

MaintEnancE

Item 58909

For technical questions, please call 1-888-866-5797.

Page 11

SaFEty

SEtup

user-Maintenance instructions
procedures not specifically explained in this manual must be performed only by a qualified technician.

tO prEVEnt SEriOuS inJury FrOM acciDEntaL OpEratiOn: turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the throttle and/or turn the switch to its off position before performing any inspection, maintenance, or cleaning procedures.
tO prEVEnt SEriOuS inJury FrOM tOOL FaiLurE: Do not use damaged equipment. if abnormal noise, vibration, or leaking air occurs, have the problem corrected before further use.
tO prEVEnt SErOuS inJury FrOM EXpLOSiOn: Lubricate the tool only with specified lubricants. Lubricate the air inlet using only pneumatic tool oil. Other lubricants may damage the mechanism and may be highly flammable, causing an explosion.

cleaning, Maintenance, and Lubrication

note: These procedures are in addition to the regular checks and maintenance explained as part of the regular operation of the air-operated tool.

1. BEFOrE EacH uSE, inspect the general 3. periodically – Lubrication:

condition of the tool. Check for:

a. Lubricate the internal mechanism

· loose hardware or housing,

of the tool, using white lithium

· misalignment or binding of moving parts,

grease in the grease fitting.

· cracked or broken parts, and · any other condition that may

b. Apply a few drops of tool oil to the Throttle. Press the Throttle a few times to lubricate.

affect its safe operation.

4. Quarterly (every 3 months)

2. Daily – air Supply Maintenance: Every day, maintain the air supply according to the component manufacturers’ instructions. Maintain the lubricator’s oil level. Drain the moisture filter regularly. Performing routine air supply maintenance will allow the tool to operate more safely

tool Disassembly, cleaning, and inspection: Have the internal mechanism cleaned, inspected, and lubricated by a qualified technician. If any Vanes need replacement, replace them all as a set.

and will also reduce wear on the tool.

OpEratiOn

MaintEnancE

Page 12

For technical questions, please call 1-888-866-5797.

Item 58909

SaFEty

SEtup

troubleshooting

problem

possible causes

Decreased output. 1. Not enough air pressure and/or air flow.

2. Obstructed throttle.
3. Incorrect lubrication or not enough lubrication.
4. Blocked air inlet screen (if equipped).
5. Air leaking from loose housing.
6. Mechanism contaminated.

7. Vane wear or damage.

Severe air

1. Cross-threaded housing

leakage.

components.

(Slight air leakage

is normal,

especially on older tools.)

2. Loose housing.

Housing heats during use.

3. Damaged valve or housing.
4. Dirty, worn or damaged valve.
1. Incorrect lubrication or not enough lubrication.
2. Worn parts.

Likely Solutions
1. Check for loose connections and make sure that air supply is providing enough air flow (CFM) at required pressure (PSI) to the tool’s air inlet. Do not exceed maximum air pressure.
2. Clean around throttle to ensure free movement.
3. Lubricate using air tool oil according to directions.
4. Clean air inlet screen of buildup.
5. Make sure housing is properly assembled and tight.
6. Have qualified technician clean and lubricate mechanism. Install in-line filter in air supply as stated in Setup: Air Supply.
7. Replace all Vanes as a set. 1. Check for incorrect alignment
and uneven gaps. If cross-threaded, disassemble and replace damaged parts before use. 2. Tighten housing assembly. If housing cannot tighten properly, internal parts may be misaligned. Technician needs to disassemble tool, align parts and reassemble. 3. Replace damaged components.
4. Clean or replace valve assembly.
1. Lubricate using air tool oil according to directions.
2. Have qualified technician inspect internal mechanism and replace parts as needed.

Follow all safety precautions whenever diagnosing or servicing the tool. Disconnect air supply before service.

OpEratiOn

MaintEnancE

Item 58909

For technical questions, please call 1-888-866-5797.

Page 13

SaFEty

SEtup

pLEaSE rEaD tHE FOLLOWinG carEFuLLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

parts List and Diagram

parts List

part
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21

Description
Pin 3×24 Trigger Housing Grip Air Inlet Screw Cap Valve Bushing Housing O-ring 3.3×1.5 O-ring 4×2 Valve Stem Spring Air Regulator O-ring 7×2 O-ring 11×2 Muffle Cover Bearing End Plate Pin 2×6 Rotor Vane Cylinder

Qty
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 4 1

part
22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41

Description
Bushing Front Plate Bearing Pinion O-ring 22.4×1.8 Lock Nut Screw Cap Angle Head Oil Valve Bearing Felt Washer Gear Screw Set Semicircular Key Drive Shaft Collet 1/4″ Collet Nut Wrench I Wrench II Collet 1/8″

Qty
1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1

OpEratiOn

MaintEnancE

record product’s Serial number Here: note: If product has no serial number, record month and year of purchase instead.

note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Specify UPC 193175448965 when ordering parts.

Page 14

For technical questions, please call 1-888-866-5797.

Item 58909

assembly Diagram

SaFEty

SEtup

OpEratiOn

MaintEnancE

Item 58909

For technical questions, please call 1-888-866-5797.

Page 15

Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS. To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise. If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product. This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
26677 agoura road · calabasas, ca 91302 · 1-888-866-5797