LC-RC01 Remote Control Panel
Product Information:
The LC-RC01 is a remote control panel designed for use with
Lumens products. It features a power adapter, USB control
connector, DC power input interface, and RJ-45 network port. The
control panel is used for connecting to the recording system and
the USB port on the recording system. It also connects to the power
cord originally connected to the recording system and the RJ45
network port of the control box. The control box has a USB 2.0
port, function buttons, and an RJ-45 port.
The LC-RC01E is designed for use in Europe, while the LC-RC01U
is designed for use in North America.
Product Usage Instructions:
Chapter 1: Package Contents
- LC-RC01 Remote control panel
- Power Adapter
- M3 x4 Flat Head screws (x2)
- Quick Installation Guide
Chapter 2: Product Overview
The LC-RC01 adapter has various connectors and ports:
- DC Power output connector
- USB control connector
- DC power input interface
- RJ-45 network port
The LC-RC01 control box has additional ports and buttons:
- USB 2.0 port
- Function buttons
- RJ-45 port
Chapter 3: Instruction for installation
To install the LC-RC01:
- Secure the adapter to the media processor with screws and
connect the DC power and USB. - Use a CAT5e network cable (not exceeding 30 meters) for
connection. - Pass a cable tie through the mounting hole to secure the
network cable onto the LC-RC01 control box. - Install the control box on the wall.
Chapter 4: Function Description
The LC-RC01 remote control panel has various button
functions:
- USB 2.0 Port: Used for inserting a USB flash disk.
- 1 / 2 / 3 Switch: Changes the scene and camera preset
position. - STREAM: Starts and stops streaming.
- BACKUP: Starts and stops backup of the last video
directory. - RECORD: Starts and stops recording.
The LC-RC01 control panel also has LED indicators that provide
status information for different functions.
LC-RC01
Remote control panel
(Remote Control Panel)
User Manual – English
[Important] To download the latest version of Quick Start Guide, multilingual user manual, software, or driver, etc., please visit Lumens https://www.MyLumens.com/support
Table of Contents
Chapter 1 Package Contents ……………………………………………………………………………………. 2 Chapter 2 Product Overview…………………………………………………………………………………….. 3
2.1 LC-RC01 adapter…………………………………………………………………………………………….. 3 2.2 LC-RC01 control box ………………………………………………………………………………………. 3 2.3 Size………………………………………………………………………………………………………………… 4 Chapter 3 Instruction for installation ………………………………………………………………………… 5 3.1 Secure the adapter to the media processor with screws and connect the DC power
and USB. ………………………………………………………………………………………………………… 5 3.2 Use the CAT5e network cable for connection (the length shall not exceed 30
meters) …………………………………………………………………………………………………………… 5 3.3 Pass a cable tie through the mounting hole to secure the network cable onto the
LC-RC01 control box. ……………………………………………………………………………………… 6 3.4 Install the control box on the wall ……………………………………………………………………. 6 Chapter 4 Function Description ……………………………………………………………………………….. 7 4.1 Button function description …………………………………………………………………………….. 7 4.2 LED Indicator Description ……………………………………………………………………………….. 7 4.3 Web Page Function…………………………………………………………………………………………. 8 Chapter 5 Troubleshooting ………………………………………………………………………………………. 9 Chapter 6 Safety Instructions …………………………………………………………………………………. 10 Copyright Information ………………………………………………………………………………………………. 11
English-1
Chapter 1 Package Contents
LC-RC01
Power Adapter
(Appearance may vary depending on country/ region)
M3 x4 Flat Head(x2)
Quick Installation Guide
English-2
Chapter 2 Product Overview
2.1 LC-RC01 adapter
NO.
Item
1.
DC Power output connector
2.
USB control connector
3.
DC power input interface
4. RJ-45 network port
Function Descriptions
Connecting to the recording system
Connecting to the USB port on recording system
<Remark> LC200 needs to connect to the USB port “below”
Connecting the power cord originally connected to the recording system to this power input port Connecting to RJ45 network port of the control box
2.2 LC-RC01 control box
Front View
Bottom
NO.
Item
5. USB 2.0 port
6. Function buttons
7. RJ-45 port
Function Descriptions The USB flash disk can be inserted for backup Please refer to 4.1 Button function description Connecting to RJ45 network port of the adapter
English-3
2.3 Size
LC-RC01E EU Regulations
LC-RC01U North America
Regulations
English-4
Chapter 3 Instruction for installation
3.1 Secure the adapter to the media processor with screws and connect the DC power and USB.
LC100 / LC100N
LC200
3.2 Use the CAT5e network cable for connection (the length shall not exceed 30 meters)
CAT5e Network Cable
English-5
3.3 Pass a cable tie through the mounting hole to secure the network cable onto the LC-RC01 control box.
3.4 Install the control box on the wall
Cable tie
English-6
Chapter 4 Function Description
4.1 Button function description
USB 2.0 Port: Is available for inserting the USB flash disk
1 / 2 / 3 Switch the Marco setting 1~3 to change the scene and camera preset position. Please refer to 4.3.2 Macro Settings for relevant settings.
STREAMPress the button once to begin streaming; press the button again to stop streaming
BACKUPPress the button once to start the backup; press the button again to stop the backup (back up the last video directory to the
RECORDPress the button once to begin recording; press the button again
4.2 LED Indicator Description
Button 1 / 2 / 3 BACKUP
STREAM Record
Indicator
Status description
N
The device is not in Macro mode
Blue light N
Blue light
Blue light flickering
Red light flickering 6 times N Blue light Red light
The device is in Macro mode
The USB flash disk is not detected by the recording system The USB flash disk is detected by the recording system The device is backing up the data onto the USB flash disk Press again to cancel back up Error in writing the data into the USB flash disk
Unpowered
Powered, but Push is not enabled Press again to enable Push
Pushing; press again to stop Push
N
Blue light
Red light Red light flickering 6 times
Unpowered Powered, but the record is not enabled Press again to enable the record Recording; press again to stop record
Error or failure during recording
<Remark> All indicators turn into flickering blue light: LC-RC01 is not connected to the recording system. Please check the connection of the recording system.
English-7
4.3 Web Page Function
4.3.1 Remote control panel connection Log in to the web page, Click [System] > [Remote Control Panel] to check the connection status between the recording system and LC-RC01 Connected
Disconnected
4.3.2 Macro Settings Log in to the web page, Click [Scenes] > [Macro] LC-RC01 [1~3] buttons correspond to Macro [1~3] Settings
1
2
3
NO.
Function Descriptions
Select a scene to be set. Each supports up to 9 sets of scene.
1 <Remark> If the layout of the scene needs to be change, please refer to
the user manual of recording system
Set/Cancel [Camera Preset Position]. Each supports up to 9 2 sets of camera preset position selection.
English-8
Chapter 5 Troubleshooting
This chapter describes problems you may encounter while using LC-RC01. If you have questions, please refer to related chapters and follow all the suggested solutions. If the problem still occurred, please contact your distributor or the service center.
NO.
Problems
Solutions
1 After installation, LC-RC01 is not detected by the recording system
Please refer to Chapter 3 Instruction for installation to ensure that USB cable is inserted into the “below” USB port of LC200 Please refer to Chapter 3 Instruction for
2 No indicator is shown on the LC-RC01 panel
installation to ensure that the control box properly connects to the adapter by the CAT5e
network cable
English-9
Chapter 6 Safety Instructions
Always follow these safety instructions when setting up and using the LC-RC01 Remote Control Panel: 1 Operation
1.1 Please use the product in the recommended operating environment, away from water or source of heat 1.2 Do not place the product on a tilted or unstable trolley, stand or table. 1.3 Please clean the dust on the power plug prior to usage. Do not insert the product’s power plug into a
multiplug to prevent sparks or a fire. 1.4 Do not block the slots and openings in the case of the product. They provide ventilation and prevent the
product from overheating. 1.5 Do not open or remove covers, otherwise it may expose you to dangerous voltages and other hazards.
Refer all servicing to licensed service personnel. 1.6 Unplug the product from the wall outlet and refer servicing to licensed service personnel when the following
situations happen: If the power cords are damaged or frayed. If liquid is spilled into the product or the product has been exposed to rain or water. 2 Installation 2.1 For security considerations, please make sure the standard mount you use is in line with UL or CE safety approbations and installed by technician personnel approved by agents. 3 Storage 3.1 Do not place the product where the cord can be stepped on as this may result in fraying or damage to the lead or the plug. 3.2 Unplug this product during thunderstorms or if it is not going to be used for an extended period. 3.3 Do not place this product or accessories on top of vibrating equipment or heated objects. 4 Cleaning 4.1 Disconnect all the cables prior to cleaning and wipe the surface with a dry cloth. Do not use alcohol or volatile solvents for cleaning. 5 Batteries (for products or accessories with batteries) 5.1 When replacing batteries, please only use similar or the same type of batteries 5.2 When disposing of batteries or products, please adhere to the relevant instructions in your country or region for disposing of batteries or products
Precautions This symbol indicates that this equipment may contain dangerous voltage which could cause electric shock. Do not remove the cover (or back). No user-serviceable parts inside. Refer servicing to licensed service personnel.
This symbol indicates that there are important operating and maintenance instructions in this User Manual with this unit.
FCC This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Notice : The changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.. FCC 15 A
IC Warning This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux appareils numeriques de Classe A prescrites dans la norme sur le material brouilleur: “Appareils Numeriques,” NMB-003 edictee par l’Industrie.
EN55032 CE Warning Operation of this equipment in a residential environment could cause radio interference. Warning: Operation of this equipment in a residential environment may cause radio interference
English-10
Copyright Information
Copyrights © Lumens Digital Optics Inc. All rights reserved. Lumens is a trademark that is currently being registered by Lumens Digital Optics Inc. Copying, reproducing or transmitting this file is not allowed if a license is not provided by Lumens Digital Optics Inc. unless copying this file is for the purpose of backup after purchasing this product. In order to keep improving the product, the information in this file is subject to change without prior notice. To fully explain or describe how this product should be used, this manual may refer to names of other products or companies without any intention of infringement. Disclaimer of warranties: Lumens Digital Optics Inc. is neither responsible for any possible technological, editorial errors or omissions, nor responsible for any incidental or related damages arising from providing this file, using, or operating this product.
English-11
Download | Lumens
