TD10049C Elis 3-Light Black Farmhouse Linear Island Chandelier Light

Product Information: 3-Light Chandelier

The 3-Light Chandelier is a lighting fixture that comes with a
fixture body, shade, socket ring, stem, loop, canopy, canopy lock
ring, mounting strap, screw, wire connector, and wiring
instructions. The fixture is designed to be connected to an outlet
box and has two groups of wires – Group A (Green, Bare copper wire,
White Ribbed) and Group B (Smooth, Black). The product is designed
for indoor use only and must be cleaned with a soft cloth and mild
soap. Abrasive materials such as scouring pads or powders, steel
wool or abrasive paper should not be used.

Product Usage Instructions

1. Unscrew Socket ring (C), place Shade (B) to the socket, then
   screw Socket ring (C) to fix the Shade (B).
2. Install Stem (D) and Loop (E) to Fixture body (A).
3. Link Loop (E) and Canopy (H) by Lock catch (F).
4. Fix Mounting strap (J) to outlet box with Screw (I).
5. Connect the wires according to the wiring instruction
   provided.
6. Fix Canopy (H) to Mounting strap (J) with Canopy lock ring
   (G).

Wiring Instructions

1. Insert the green grounding screw into the hole with two raised
   dimples on the mounting bar. Wrap the ground wire from the fixture
   (if supplied) around the green grounding screw, then connect it to
   ground wire from the outlet box (if not fixed on the outlet box)
   using a wire connector(not supplied). If ground wire from the
   fixture is not supplied, wrap the ground wire (if not fixed on the
   outlet box) from the outlet box around the green grounding screw
   and tighten it. NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER
   SUPPLY WIRES.
2. Take note of the color of the wire(s) on your fixture. Identify
   which group your fixture wire(s) falls into and connect the wires
   according to the directions below:
   [GROUP A]: Connect to Black House Wire
   [GROUP B]: Connect to White House Wire
3. Take your fixture wire(s) from [Group A] and place evenly
   against the black wire from the outlet box. Do NOT twist wires
   together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector
   clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull
   the connector off, carefully re-do steps 3 and 4 as above, and
   check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from
   the outlet box in the same manner. Make sure no bare wires can be
   seen outside wire connectors.

Safety Information

Always switch off the electricity supply and allow to cool for
10 minutes before changing the light bulbs.

Contact Us

E-mail:[email protected]

Printed in China

Instruction Manual
3-Light Chandelier

Overview
Outlet box Black
Wire nuts Smooth
[GROUP A] F.Lock catch

Green(Ground)

Bare copper wire(Ground)

White Ribbed

J.Mounting strap

I.Screw

H.Canopy G.Canopy lock ring
E.Loop

D.Stem

A.Fixture body
B.Shade
C.Socket ring
Assembly Instruction
1.Unscrew Socket ring (C), place Shade (B) to the socket, then screw Socket ring (C) to fix the Shade (B).
2.Install Stem (D) and Loop (E) to Fixture body (A). 3.Link Loop (E) and Canopy (H) by Lock catch (F). 4.Fix Mounting strap (J) to outlet box with Screw (I). 5.Connect the wires according to the picture above.
(Please refer to the wiring instruction for details ) 6.Fix Canopy (H) to Mounting strap (J) with Canopy lock ring (G).

Wiring Instruction

1. Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector(not supplied). If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.

NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.

2.Take note of the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

BLACK

WHITE

*PARALLEL WIRE (round & smooth) *PARALLEL WIRE (square & ridged)

WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK WITHOUT TRACER

BROWN, GOLD OR BLACK WITH TRACER

3.Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors. 4.Fit a wire connector over the wires and screw the connector clockwise until you feel firmness. 5.Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps 3 and 4 as above, and check again for a firm connection.
6.Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications

Input voltage 120V Rated power 60W MAX × 3 Lamp socket E26 Cord Length 7ft.
Product Packaging
Fixture body × 1 Stem × 8 Loop × 2 & Lock catch × 2 Mounting strap × 1 & Canopy × 1 Screw × 2 & Wire nut × 3 Glass shade × 4 & Glass holder cup × 4 Lamp instruction × 1

Cleaning
To clean, wipe fixture with a soft cloth. Clean glass with a mild soap. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.

CONTACT US
E-mail:[email protected]

Print in china

References

• Digital Services, Technology and Consulting | Reply