PKRB1000 Rollester Gold Rollerball Pen Kit
Product Information
- Product Name: Rollester Pen Kit
- Model Number: PKRB10XX
- Manufacturer: PSI Woodworking Products
- Required Accessories: Tip Cap, Refill, Coupler Tip, Tube/Barrel
(length: 3.30), Spring, End Cap Clip, Head Stock, End Bushing,
Knurled Nut, Live Center, 7mm Spacer Bushings, Mandrel, Bushings
(#PKCHPENBU)
Product Usage Instructions
Preparing the Blank:
To prepare the blank, follow these steps:
- Use a power disc sander to shape the blank.
- Take the excess material down flush with the ends of the brass
tube. - Do not trim beyond the length of the tube as it may interfere
with the assembly’s operation.
Turning the Blank:
To turn the blank, follow these steps:
- Refer to Diagram B for turning the blanks.
- Use the 7mm spacer bushings to achieve the desired
profile. - Follow the polish instructions for finishing.
Assembly:
To assemble the pen kit, follow these steps:
- Refer to Diagram C for assembly.
- Ensure that the bushings (#PKCHPENBU) are properly
aligned. - Drill .248 holes through the same bushings.
- Follow the manufacturer’s instructions for attaching the
required accessories.
#PKRB10XX
Rollester Pen Kit
PKRB1000 · PKRB1010 · PKRB1015 · PKRB1020
Kit Features:
· Easy to turn with a straight tube · Minimum parts – easy to assemble · Uses standard Rollerball refill · Available in multiple finishes · Overall Length: 5-1/16″
Required Accessories:
· 7mm Pen Mandrel · Drill Bit: 3/8″ #PKEXEC-38 · Bushing set(2 pc) #PKCHPENBU · Barrel Trimming set #PKTRIM38 · Live Tailstock Center · 2 Part Epoxy Glue or Insta Cure (Cyanoacrylate) Glue · Pen Blank: Minimum Size – 3/4″ x 3-1/2″ Long
PSI Woodworking Products
Tip Cap
DIAGRAM A / PARTS LAYOUT
Coupler Tip
Tube/Barrel 3.30″
Refill
Spring
End Cap Clip
Preparing the Blank:
· Cut a blank to the length of the tube and add 1/16″ for squaring off. · Drill a 3/8″ hole lengthwise through the blank. · Spread glue over the tube, insert the blank with a twisting motion to spread the glue evenly inside. · Center the tube lengthwise inside the blank. · When the glue is dry, square the ends of the blank. Use a 3/8″ barrel trimmer or a universal pen blank squaring jig
with a power disc sander. Take the excess material down flush with the ends of the brass tube. (do not trim beyond the length of the tube since this may interfere with operation of the assembly).
#PKRB10XX
Head Stock
End Bushing
PSI Woodworking Products
DIAGRAM B / TURNING THE BLANKS
Blank
End Bushing
Knurled Nut
Live Center
7mm Spacer Bushings
Turning the Blank
Finished Profile
7mm Spacer Bushings
Mandrel
· Mount the bushings and blanks according to diagram B. · Thread on the knurled nut and hand tighten to hold all components in place. · Slide the tailstock up snugly against the mandrel shaft inserting the live center point into the mandrel
dimple, lock in place. · Hand tighten the quill adjustment to firm up the mandrel. (DO NOT overtighten, it could damage the
mandrel. · Using sharp tools, turn the blank down close to the bushing diameter. Turn the barrel (straight or to a
profile of your choice) · Sand the blank down to be flush with the bushings gradually increasing the sandpaper grits. · Finish the barrel with your choice of polish. Allow sufficient time for the polish to cure.
Refer to polish instructions.
Assembly
· Layout parts according to diagram A , pull out tip and coupler from inside of tip cap. · Press the coupler into either end of the barrel. · Feed the cap through the clip, press into the opposite end of the barrel. · Drop the spring into the opening in the coupler. · Pull the refill cover off the refill, slide the refill into the barrel pushing the spring to the end. · Screw the tip over the refill into the coupler. · Place the tip cover / retainer assembly over the tip, pushing in until a click is heard. · When not in use, it is reccomended to keep the cover on.
Diagram C / Bushings #PKCHPENBU
ø.445″
ø.345″
SAME
.248″ Holes through
© 2013 PSI Woodworking Philadelphia PA 19115 – v05/22
