P5394-613 Gramercy 4-Light Polished Nickel Shaded Pendant Light
Product Information: PINSTALLATION INSTRUCTIONS
The PINSTALLATION INSTRUCTIONS provide step-by-step guidance for
installing Item#P5394-613. The product comes with a mounting plate
(A), rod (E), cross assembly (K), canopy (C), decorative parts (L),
cloth shade (H), medium base bulbs (J) and screws (B, D, and
I).
Preparation
- Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. - Unpack the new fixture and lay out all the parts in a clean
area. Take care not to misplace any small parts necessary for
installation. - Secure rod (E) onto all thread (G) on cross assembly (K).
- Determine the desired hanging height and thread rods (F1, F2,
and F3) to the all thread on rod (E). Attach canopy (C) by screwing
onto rod (F1). Carefully pass the wires through each rod during
assembly. Note: Remove the all thread if installing with one 6 rod
only. - Attach mounting plate (A) to the junction box with mounting
screws (B) (Size: #8-32N*L0.5). The side of the mounting plate (A)
with GND marked on it and two convex points must face out.
Connecting the Wires
- Connect the electrical wires as shown in fig 2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect the fixture’s ground
wire to it. Otherwise, connect the fixture’s ground wire directly
to the mounting plate (A) using the green screw provided. - Tuck wire connectors neatly into the junction box.
Finishing the Installation
- Place canopy (C) over mounting plate (A) and secure with screws
(D). - Install (4) four medium base bulbs (J) up to 60 watts each or
CFL or LED equivalent (not included) in accordance with the fixture
specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!). - Secure decorative parts (L) on cross assembly (K) with screws
(I). - Place cloth shade (H) onto cross assembly (K) and secure with
screws (I).
Your installation is now complete. Return power to the junction
box and test the fixture. Note: Illustration (Fig. 1) on this
manual is for installation purposes only. It may or may not be
identical to the fixture purchased.
PINSTALLATION INSTRUCTIONS
Item#P5394-613 (New. 2022/4/07) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
PREPARATION (Fig.1) 1. Shut off power at the fuse box or circuit breaker box and
remove the old fixture including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts
in a clean area. Take care not to misplace any small parts
necessary for installation. 3. Secure rod (E) onto all thread (G) on cross assembly (K). 4. Determine the desired hanging height and thread rods
(F1, F2 and F3) to the all thread on rod (E). Attach canopy
(C) by screwing onto rod (F1). Carefully pass the wires
through each rod during assembly. Note: Remove the all
thread, if installing with one 6″ rod only. 5. Attach mounting plate (A) to the junction box (not
included) with mounting screws (B) (Size: #8-32N*L0.5″).
The side of the mounting plate (A) with “GND” marked on
it and two convex points must face out.
CONNECTING THE WIRES (Fig. 2) 6. Connect the electrical wires as shown in fig 2, making
sure that all wire connectors are secured. If your junction
box has a ground wire (green or bare copper), connect the
fixture’s ground wire to it. Otherwise, connect the fixture’s
ground wire directly to the mounting plate (A) using the
green screw provided. 7. Tuck wire connectors neatly into the junction box. FINISHING THE INSTALLATION (Fig.1) 8. Place canopy (C) over mounting plate (A) and secure with
screws (D). 9. Install (4) four medium base bulbs (J) up to 60 watts each
or CFL or LED equivalent (not included) in accordance
with the fixture specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS DEPASSER LA PUISSANCE NOMINALE MAXIMALE!). 10. Secure decorative parts (L) on cross assembly (K) with screws (I). 11. Place cloth shade (H) onto cross assembly (K) and secure with screws (I).
Fig. 1 Set#A-021-118DH -Mounting plate -Ground screw -Mounting screw*2
I
A B C D F1 F2 F3 E
Rod# W30-1-613*1(F1) I W30-1-613 *2(F2) H W30-H-613 *1(F3)
G K
J L
Your installation is now complete. Return power to the junction box and test the fixture.
Note: Illustration (Fig. 1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
Fig. 2 FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
FIXTURE WIRES Bare Copper (Ground)
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
HOUSE WIRES Green (Ground)
Page:1/1
LA-3508E
