Hornit Mudguard 14 Inch Hero Set Instruction Manual

Mudguard 14 Inch HERO Set

Product Information: Mudguard Installation

The Mudguard Installation is a set of components designed to
provide protection against mud, dirt, and water while riding your
bike. It includes front and rear mudguards, stays, screws, bolts,
nuts, washers, and brackets. The installation process requires
tools such as 3, 4 & 5mm Allen keys, 1 Phillips Screwdriver,
8mm or adjustable Spanner, and a Bike Pump.

Assembly Components

• Front Mudguard
• Front Stay
• x2 Phillips Screw
• x1 Long Socket Bolt
• x1 Nut
• x1 Washer
• x1 Inner Bracket
• x1 Outer Bracket

Tools Required

• 3, 4 & 5mm Allen keys
• 1 Phillips Screwdriver
• 8mm or adjustable Spanner
• Bike Pump

Product Usage Instructions: Mudguard Installation

1. Rest the bike upside down on a soft surface such as carpet.
   Undo the brake callipers and remove front wheel by loosening axle
   bolts and carefully lifting out of droputs.
2. Insert the first Phillips head screw for the stay bracket until
   finger tight (you will securely fasten later). Insert the stay and
   secure with the second screw.
3. Attach the mudguard by placing the mounting plate at the rear
   of the forks, insert the long socket bolt and washer then thread
   the nut until finger tight. Using a 4mm Allen key attach the stay
   loops to the forks using existing bolts.
4. Locate the wheel in the dropouts and tighten axle bolts. Check
   mudguard alignment then tighten the Phillips head screws in the
   bracket. Using a spanner and 5mm Allen key, tighten the socket bolt
   until fully secure. Reattach brake and test.
5. Attach stay to mudguard using brackets and Phillips head screws
   until finger tight (you will securely fasten later). Place mudguard
   around wheel. Attach stay loops to dropout eyelet mounting points
   with socket screws using 3mm Allen key, note hole position.
6. Deflate tyre by removing valve cap and pushing metal pin with
   an Allen key. Compress tyre to increase access. Extend kickstand if
   fitted and attach hex head screw to kickstand mounting plate using
   your fingers, finishing with 8mm spanner. It can be convenient to
   have someone help with this. Insert push rivet into mounting point
   on seat stay bridge – press firmly with finger or thumb.
7. Reinflate tyre 40-65psi(2.8-4.6bar) and check braking action
   and that mudguard sits true. Tighten all fixings.

Mudguard Installation

ASSEMBLY Components

Tools required

3, 4 & 5mm Allen keys
1

Phillips Screwdriver

8mm or adjustable Spanner

Bike Pump

FRONT Components

Front Mudguard

Front Stay

x2 Phillips Screw x1 Long Socket Bolt x1 Nut x1 Washer x1 Inner Bracket x1 Outer Bracket

Rest the bike upside down on a soft surface such as carpet. Undo the brake callipers and remove front wheel by loosening axle bolts and carefully lifting out of droputs.

Insert the first Phillips head screw for the stay bracket until finger tight (you will securely fasten later).

Insert the stay and secure with the second screw.
2

Attach the mudguard by placing the mounting plate at the rear of the forks, insert the long socket bolt and washer then thread the nut until finger tight.
Using a 4mm Allen key attach the stay loops to the forks using existing bolts.
3

Locate the wheel in the dropouts and tighten axle bolts. Check mudguard alignment then tighten the Phillips head screws in the bracket.
Using a spanner and 5mm Allen key, tighten the socket bolt until fully secure.
Reattach brake and test.
4

REAR Components

Rear Mudguard

Rear Stay

x1 Push Rivet x1 Hex Head Screw x2 Socket Screws x2 Phillips Screws x1 Inner Bracket x1 Outer Bracket

Attach stay to mudguard using brackets and Phillips head screws until finger tight (you will
securely fasten later).
5

Place mudguard around wheel.
Attach stay loops to dropout eyelet mounting points with socket screws using 3mm Allen key, note hole position.
6

Deflate tyre by removing valve cap and pushing metal pin with an Allen key. Compress tyre to increase access. Extend kick stand if fitted and attach hex head screw to kick stand mounting plate using your fingers, finishing with 8mm spanner. It can be convenient to have someone help with this.
Insert push rivet into mounting point on seat stay bridge – press firmly with finger or thumb.
Reinflate tyre 40-65psi(2.8-4.6bar) and check braking action and that mudguard sits true. Tighten all fixings.
7