Hornit Hero 14 Kids Bike Instruction Manual

HERO 14 Kids Bike

Product Information: Mudguard Installation

The Mudguard Installation kit comes with components required for
both front and rear mudguard installation. The kit includes Front
Mudguard, Front Stay, Rear Mudguard, Rear Stay, screws, bolts,
nuts, washers, and brackets. The tools required for installation
are 3, 4 & 5mm Allen keys, 1 Phillips Screwdriver, 8mm or
adjustable Spanner, and Bike Pump.

Assembly Components for Front Mudguard

• Front Mudguard
• Front Stay
• x2 Phillips Screw
• x1 Long Socket Bolt
• x1 Nut
• x1 Washer
• x1 Inner Bracket
• x1 Outer Bracket

Assembly Components for Rear Mudguard

• Rear Mudguard
• Rear Stay
• x1 Push Rivet
• x1 Hex Head Screw
• x2 Socket Screws
• x2 Phillips Screws
• x1 Inner Bracket
• x1 Outer Bracket

Product Usage Instructions: Mudguard Installation

Front Mudguard Installation Steps:

1. Rest the bike upside down on a soft surface such as
   carpet.
2. Undo the brake callipers and remove front wheel by loosening
   axle bolts and carefully lifting out of droputs.
3. Insert the first Phillips head screw for the stay bracket until
   finger tight (you will securely fasten later).
4. Insert the stay and secure with the second screw.
5. Attach the mudguard by placing the mounting plate at the rear
   of the forks, insert the long socket bolt and washer then thread
   the nut until finger tight.
6. Using a 4mm Allen key attach the stay loops to the forks using
   existing bolts.
7. Locate the wheel in the dropouts and tighten axle bolts. Check
   mudguard alignment then tighten the Phillips head screws in the
   bracket.
8. Using a spanner and 5mm Allen key, tighten the socket bolt
   until fully secure.
9. Reattach brake and test.

Rear Mudguard Installation Steps:

1. Attach stay to mudguard using brackets and Phillips head screws
   until finger tight (you will securely fasten later).
2. Place mudguard around wheel.
3. Attach stay loops to dropout eyelet mounting points with socket
   screws using 3mm Allen key, note hole position.
4. Deflate tyre by removing valve cap and pushing metal pin with
   an Allen key. Compress tyre to increase access. Extend kick stand
   if fitted and attach hex head screw to kickstand mounting plate
   using your fingers, finishing with 8mm spanner. It can be
   convenient to have someone help with this.
5. Insert push rivet into mounting point on seat stay bridge –
   press firmly with finger or thumb.
6. Reinflate tyre 40-65psi (2.8-4.6bar) and check braking action
   and that mudguard sits true. Tighten all fixings.

Mudguard Installation

ASSEMBLY Components

Tools required

3, 4 & 5mm Allen keys
1

Phillips Screwdriver

8mm or adjustable Spanner

Bike Pump

FRONT Components

Front Mudguard

Front Stay

x2 Phillips Screw x1 Long Socket Bolt x1 Nut x1 Washer x1 Inner Bracket x1 Outer Bracket

Rest the bike upside down on a soft surface such as carpet. Undo the brake callipers and remove front wheel by loosening axle bolts and carefully lifting out of droputs.

Insert the first Phillips head screw for the stay bracket until finger tight (you will securely fasten later).

Insert the stay and secure with the second screw.
2

Attach the mudguard by placing the mounting plate at the rear of the forks, insert the long socket bolt and washer then thread the nut until finger tight.
Using a 4mm Allen key attach the stay loops to the forks using existing bolts.
3

Locate the wheel in the dropouts and tighten axle bolts. Check mudguard alignment then tighten the Phillips head screws in the bracket.
Using a spanner and 5mm Allen key, tighten the socket bolt until fully secure.
Reattach brake and test.
4

REAR Components

Rear Mudguard

Rear Stay

x1 Push Rivet x1 Hex Head Screw x2 Socket Screws x2 Phillips Screws x1 Inner Bracket x1 Outer Bracket

Attach stay to mudguard using brackets and Phillips head screws until finger tight (you will
securely fasten later).
5

Place mudguard around wheel.
Attach stay loops to dropout eyelet mounting points with socket screws using 3mm Allen key, note hole position.
6

Deflate tyre by removing valve cap and pushing metal pin with an Allen key. Compress tyre to increase access. Extend kick stand if fitted and attach hex head screw to kick stand mounting plate using your fingers, finishing with 8mm spanner. It can be convenient to have someone help with this.
Insert push rivet into mounting point on seat stay bridge – press firmly with finger or thumb.
Reinflate tyre 40-65psi (2.8-4.6bar) and check braking action and that mudguard sits true. Tighten all fixings.
7