VT-11108 8W Solar LED Floodlight
Product Information:
- Product Name: SOLAR LED FLOODLIGHT
- Model: VT-11108
- Lumens: 950LM
- Watts: 8W
- Number of LEDs: 64 PCS
- Battery Type: 3.7V Lithium Battery, 4000mAh
- Beam Angle: [Information missing]
- Sensing Range: [Information missing]
- Charging Time: [Information missing]
- Working Time: [Information missing]
- Material: [Information missing]
Product Usage Instructions:
- Place the SOLAR LED FLOODLIGHT in an outdoor location with
direct access to sunlight. - Before initial use, ensure that the battery is fully charged by
exposing the solar panel to sunlight for the recommended charging
time. - To turn on the floodlight, locate the power switch and toggle
it to the “ON” position. - The floodlight will automatically activate when it detects
motion within its sensing range. Adjust the sensing range according
to your preference, if applicable. - The floodlight will provide illumination for the specified
working time after each full charge. - If the floodlight does not turn on or does not provide
sufficient illumination, check the battery level and ensure that
the solar panel is receiving adequate sunlight. - For maintenance and cleaning, gently wipe the surface of the
floodlight with a soft cloth. Do not use abrasive cleaners or
solvents.
Please note that the missing information regarding beam angle,
sensing range, charging time, working time, and material should be
obtained from the product user manual for accurate usage
instructions.
SOLAR LED FLOODLIGHT
TECHNICAL DATA:
MODEL
VT-11108
LUMENS
950LM
WATTS
8W
NO. OF LEDs
64 PCS
BATTERY TYPE 3.7V Lithium Baery, 4000mah
BEAM ANGLE
120°
SENSING RANGE CHARGING TIME WORKING TIME
MATERIAL
<8 Meters 5-6 Hours Sunlight Charging
Min 20 – Max 60 Hours ABS+PC
IP65
RATING
2
WARRANTY*
YEARS
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at the best. The warranty is valid for 2 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. This product is warranted for manufacturing defects only.
NOTICE & WARNING
1. This is a solar powered lamp, please install it in a location where can get enough sunshine. 2. Please note the lighting time depends on sunshine duration & weather. 3. The lamp will light up automatically at dusk. 4. Recommended installation height is 3~4Mtr. 5. The lamp is equipped with an internal battery pack, which is replaceable. If any need, please contact seller for correct new battery pack. 6. Please connect the lamp to solar panel to get solar charging. 7. Built-in intelligent IC is with over-charge, over-discharge protection, safe and durable. 8. Non-professionals please do not disassemble the lamp. 9. Please do not dispose the battery with household garbage to avoid explosion.
MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages.
This marking indicates that this product should not be disposed of with other household wastes.
Caution, risk of electric shock.
20 PAP
FEATURES
Patent Design
Ultra-thin
Foldable
Adjustable
8-in-1
8 in 1 Multi Functions
Solar Powered
Auto On/Off
INSTALLATION DIAGRAM
Two Work Modes
Cordless to Install
User Manual
1PC * Lamp
2PCS * Screws with
Flat & Spring Washers (for Wall Mount
2PCS * Screws (for Hanging)
2PCS * Stickers
WIDE APPLICATIONS:
1. Integrated wall mount for garden, entrance, garage, courtyard, fence, campus etc. 2. Split wall mount for roof, corner, pathway, bus station, attic, pavilion etc. 3. Hanging for balcony light, emergency light etc. 4. Portable as flash light, camping light, emergency use etc. 5. Standable as work light, pillar light, ground light, wall washer light etc. 6. It can be magnetized on any flat metal surface for flexible use. 7. Lamp can be sticked directly for flexible use.
1PC * User Manual
TWO OPTIONAL WORKING MODES
On/Off/Select working mode
Please rotate the lamp head and press the button to select working mode. 1. Press the button 1st time, lamp turns on to Mode A. 2. Press the button 2nd time, lamp shines once and turns to Mode B. 3. Press the button 3rd time, lamp turns off.
MODE A:
120°
When battery power is more than 30% :
Lamp automatically lights up at night and
turns to 100% brightness when motion
120°
is detected in the range 8mtrs, then dim
to lower brightness after 20 seconds
of no motion.
When battery power is less than 30% :
Lamp automatically lights up at night and
turns to 100% brightness when motion
120°
120°
is detected in the range 8mtrs, then turns
off after 20 seconds of no motion.
MODE B:
Lamp automatically lights up at night and keep 100% brightness, after 5 hours or when battery power is less than 30%, lamp turns to Energy Saving Mode: Lamp automatically turns to 100% brightness when motion is detected in the range 8mtrs, then turns off after 20 seconds of no motion.
After 5 hours or when the battery power is less than 30%
120°
KIND REMIND:
When the lamp is not connected to the solar panel, the light sensor is disabled. Whether it is day or night, the lamp will stay on after it is turned on.
INSTALLATIONS:
180°
180°
360°
Rotate the lamp head to adjust lighting directions, 180° adjustable. Rotate the screw to adjust solar panel vertically, 180° adjustable. Hold the lamp base and rotate the lamp post to adjust whole lamp angle, 360° adjustable.
INSTALLATION A: INTEGRATED WALL MOUNT
6mm
58mm
Depth: 50mm
The recommended mounting height is 2-4Mtrs. Drill 2 holes (6mm, depth 50mm) with a spacing of 58mm. Fix the expansion plugs in the holes. Use screws with flat & spring washers to fix the lamp on the wall. Adjust solar panel angle and lighting direction as needed.
INSTALLATION B: SPLIT WALL MOUNT
The lamp head can be removed according to the arrows on the side of the lamp for split installation. The connection cable is 3m long, please confirm the installation position of the solar panel and the lamp before installation.
6mm
58mm
Depth: 50mm
120.3mm
3-5mm
Drill 2 holes (6mm, depth 50mm) with a spacing of height 58mm. Fix the expansion plugs in the holes. Use screws with flat & spring washers to fix the lamp on the wall. Drill 2 holes (6mm, depth 50mm) with a spacing of width 120.3mm. Fix the expansion plugs in the holes, then fix the screws into the expansion plugs, keeping the screws protruding 3-5mm. Hang the lamp on the screws. Connect the cable of the solar panel to the lamp.
MORE OPTIONAL INSTALLATION
Two-direcon Hanging Holes
Magnet
INSTALLATION C: LAMP WALL MOUNT WITH MAGNET
Metal flat surface
Check the magnet on the back. Make sure there’s no
object aached on the magnet
Fix the lamp on the metal flat surface.
Note: · To charge the lamp, connect the cable of the solar panel to the lamp · Only PIR Sensor will work if the lamp is not connected to the solar panel
INSTALLATION D: LAMP WALL MOUNT WITH STICKER
Fix the posion of the scker on the lamp Place 2 sckers properly onto the Two-direcon Hanging Holes of the lamp Remove the scker cover on the lamp Fix the lamp on the wall. Turn on the light and test the lamp Note: · To charge the lamp, connect the cable of the solar panel to the lamp · Sensor will not work if the lamp is not connected in solar panel
INSTALLATION E: LAMP WALL MOUNT WITH SCREWS
Depth: 50mm
Drill 2 holes (8mm, depth 50mm) with a spacing of 120.3mm. Fix the expansion plugs in the holes. Fix the lamp on the wall. Turn on the light and test the lamp Note:
· To charge the lamp, connect the cable of the solar panel to the lamp
· Sensor will not work if the lamp is not connected in solar panel
INSTALLATION E: PILLAR MOUNT
Depth: 50mm
Drill 2 holes (8mm, depth 50mm) with a spacing of 120.3mm. Fix the expansion plugs in the holes. Use screws with flat & spring washers to fix the lamp on the ground. Adjust solar panel angle and lighting direction as needed.
PORTABLE LAMP
Make sure that the lamp has enough charge to carry.
Turn on the light and test the lamp Note: · To charge the lamp, connect the cable of the solar panel to the lamp · Sensor will not work if the lamp is not connected in solar panel
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: [email protected] FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B
TAC.EU
