SLG-UDSD6LD Polaris Slingshot Under Dash Enclosure
Product Information:
The Polaris Slingshot Under Dash Enclosure with Dual ZR6.4D
Subwoofers is a specially designed product for the Slingshot. It
includes a box that fits under the dashboard of the Polaris
Slingshot and comes with two ZR6.4D subwoofers.
Features:
- Specifically designed for the Polaris Slingshot
- Includes dual ZR6.4D subwoofers
What’s in the Box:
The package includes the following items:
- Polaris Slingshot Under Dash Enclosure
- Dual ZR6.4D Subwoofers
- M8 Screws
- Allan Key
Product Usage Instructions:
- Open the hood of the Slingshot to access the engine bay and
locate the glovebox area on the passenger side. Look for a flat
area where two pins will align with the provided bracket. (Refer to
Picture 1) - If you have a 2017-Up model, all the necessary holes are
pre-drilled from the factory. For older models, you need to open
the required holes. (Refer to Picture 2) - Remove the subwoofers from the enclosure and remove the damping
material to access the mounting location. (Refer to Picture 3) - Place the enclosure in its final location under the dash with
the subwoofer holes facing down. (Refer to Picture 4) - Use the included M8 screws and insert them from the inside of
the box, aligning them with the previously opened holes. Use the
supplied Allen key to tighten them by hand. (Refer to Picture
5) - Reinstall the damping material and secure the subwoofers back
into the enclosure. Be careful not to over-tighten and damage the
holes or improperly secure the subwoofer. (Refer to Picture 6) - This kit requires an aftermarket amp to be pre-installed with
the speaker wires in this location. Only after this step, you can
install the speakers using the aftermarket amp’s speaker wire. - The installation of the SLG-UDSD6LD is now complete, and you
can enjoy your new sound system upgrade!
Specifications:
Speaker Specifications:
- Overall Height: 6″ / 152.4mm
- Overall Width: 14.6″ / 372mm
- Overall Depth: 7.2″ / 183mm
Box Specifications:
- Height: 0.67″ / 17mm
- Width: 7.11″ / 180.60mm
- Depth: 7.27″ / 184.67mm
- Measurement: 15.01″ / 381.16mm
Measurements:
- 2-M8
- Depth: 7.27″ / 184.65mm
- Height: 1.18″ / 30mm
- Width: 4.19″ / 106.50mm
For warranty information, please visit our website DS18.com.
WARNING:
Cancer and Reproductive Harm. www.P65Warning.ca.gov
ADVERTENCIA:
FOR MORE INFORMATION PLEASE VISIT DS18.COM
V1
OWNER’S MANUAL
MANUAL DEL USUARIO
POLARIS SLINGSHOT UNDER DASH ENCLOSURE WITH DUAL ZR6.4D SUBWOOFERS INCLUDED
CAJA PARA DEBAJO DEL TABLERO DEL POLARIS SLINGSHOT CON SUBWOOFERS DUALES ZR6.4D
INCLUIDOS
SPECIALLY
DESIGNED FOR
SLINGSHOT
ENGLISH | ESPAÑOL
POLARIS SLINGSHOT UNDER DASH ENCLOSURE WITH DUAL ZR6.4D SUBWOOFERS INCLUDED
CAJA PARA DEBAJO DEL TABLERO DEL POLARIS SLINGSHOT CON SUBWOOFERS DUALES ZR6.4D INCLUIDOS
INTRODUCTION
If you’re looking to maximize sound in your Polaris Slingshot, you may consider adding this durable Polyethylene Passenger Side Under Dash 6.5″ Subwoofer Enclosure by DS18. This enclosure allows you to mount two 6.5″ subwoofers underneath your dash to give you the bass your stereo system deserves without compromising your storage compartments. This enclosure comes with a black textured finish to match the factory’s look. Very easy to Install using supplied bolts directly into place and do not interfere with your factory glove box.
INTRODUCCIÓN:
Si está buscando maximizar el sonido en su Polaris Slingshot, puede considerar agregar esta resistente caja de polietileno para subwoofer de 6.5″ debajo del tablero para el lado del pasajero de DS18. Esta caja le permite montar dos subwoofers de 6.5″ debajo del tablero para brindarle los graves que su sistema de audio merece sin comprometer sus compartimentos de almacenamiento. Esta caja viene con un acabado texturizado negro para que coincide con el aspecto de fábrica. Muy fácil de instalar utilizando los tornillos suministrados directamente en su lugar y no interfiere con la guantera de fábrica.
FEATURES
· 600 Watts RMS Power Handling. · 1200 Watts MAX Power Handling. · Two 6.5″ ZR6.4D Subwoofers Included. · 1 Ohm Total Load Impedance. · Easy to install – All Hardware and Wiring
Included. · OFC tinned 12Ga Wiring for More Power
Handling and Durability. · Fits Slingshot Models from 2015 or later · Coated Metal Bracket for better
Resistance to the Elements. · Durable (PE) Waterproof Enclosure with
UV Protection. · 0.3ft3 / 8.5L Sealed Type Enclosure. · Damping Material for Better Subwoofers
Performance. · Black OEM Finish
WHAT’S IN THE BOX
· Subwoofer Enclosure with Two ZR6.4D Subwoofers
· Mounting Bracket · 2 x M8 x 1″ Screws and washers · 6mm Allen key
CARACTERÍSTICAS:
· Manejo de potencia de 600 Watts RMS · Manejo de potencia de 1200 Watts MAX · Dos subwoofers ZR6.4D de 6.5″ incluidos. · Impedancia de carga total de 1 ohmio. · Fácil de instalar con todo el hardware y
cableado incluidos. · Cableado OFC estañado 12Ga para mayor manejo
de potencia y durabilidad. · Se adapta a los modelos Slingshot de 2015 en
adelante. · Soporte de metal revestido para una mejor resistencia
a los elementos. · Caja resistente al agua (PE) duradera con
protección UV. · Caja de tipo sellado de 0.3 ft3 / 8.5L. · Material de amortiguación para un mayor rendimiento
de los subwoofers. · Acabados de textura negra como plásticos OEM.
QUÉ HAY EN LA CAJA:
· Caja de subwoofer con dos subwoofers ZR6.4D
· Soporte de montaje · 2 tornillos y arandelas M8 x 1″ · Llave Allen de 6 mm
INSTALLATION / INSTALACIÓN:
Open the hood of the Slingshot to get access
to the engine bay and look at the glovebox area in the passenger side, you will see a
1
plane area where two pins will align with the
bracket provide.
(Picture 1)
Abra el capó del Slingshot para acceder al compartimento del motor y mire el área de la guantera en el lado del pasajero, verá un área plana donde dos pasadores se alinearán con el soporte provisto.
(Imagen 1)
For the pass-through screws, if you have a
2
2017-Up all the holes are pre-drilled from
factory, for older model you need to open
these two holes using a ½” drill bit.
(Picture 2)
Para los tornillos pasantes, si tiene un modelo 2017 en adelante, todos los orificios vienen pretaladrados de fábrica; para los modelos más antiguos, debe abrir estos dos orificios con una broca de ½”.
(Imagen 2)
Remove the Subwoofers from the enclosure
3
and remove the damping material to get
access to the mounting location.
(Picture 3)
Retire los subwoofers de la caja y retire el material de amortiguación para acceder a la ubicación de montaje.
(Imagen 3)
Place the enclosure in the final location under
4
the dash with subwoofer holes facing down.
(Picture 4)
Coloque la caja en la ubicación final debajo del tablero con los orificios del subwoofer hacia abajo. (Imagen 4)
INSTALLATION / INSTALACIÓN:
Then use the included M8 screws and insert them from the inside of the box, align it with the previously opened holes, using the supplied Allen
5
key, tighten it as far as it will go by hand.
(Picture 5)
Luego use los tornillos M8 incluidos e insértelos desde el interior de la caja, alinéelo con los orificios previamente abiertos, usando la llave Allen suministrada, apriételo con la mano hasta el tope. (Imagen 5)
Do not forget to put back the damping material and install back the Subwoofers, be careful not
6
to over-tighten or the hole may be damaged and
not properly secure the subwoofer.
(Picture 6)
No olvide volver a colocar el material de amortiguación y volver a instalar los subwoofers, tenga cuidado de no apretar demasiado o el orificio podría dañarse y no asegurar adecuadamente el subwoofer.
(Imagen 6)
This kit needs an aftermarket amp pre-installed with the speaker wires in this location, only after this step can you install the speakers using the aftermarket amp’s speaker wire.
This concludes the installation of the SLG-UDSD6LD and it is ready to enjoy your new sound system upgrade!
Este kit necesita un amplificador adicional preinstalado con los cables de los altavoces en esta ubicación, solo después de este paso puede instalar los altavoces usando el cable del altavoz del amplificador adicional.
¡Esto concluye la instalación del SLG-UDSD6LD y está listo para disfrutar de su nueva actualización del sistema de sonido!
SPECIFICATIONS / ESPECIFICACIONES:
Speaker Size / Tamaño de altavoz.. ………………………………………………………………………………………………2 x 6.5″ Total Impedance / Impedancia Total …………………………………………………………………………………………… 1 Ohms Total RMS Power Handling / Manejo de potencia RMS total ……………………………………………………..600W Total MAX Power Handling / Manejo total de potencia MAX ……………………………………………………1200W Sensitivity (1w/1m) / Sensibilidad (1w/1m) ………………………………………………………………………………….. 90dB Frequency Response / Respuesta de Frecuencia …………………………………………………………….. 38Hz-200Hz Recommended Lo Pass Crossover / Crossover de paso bajo recomendado……………………………..120Hz
SPEAKER SPECIFICATIONS / ESPECIFICACIONES DE LOS ALTAVOCES:
Voice Coil Diameter / Diámetro de la Bobina de Voz …………………………………………………….. 1.5″ / 38.8mm Voice Coil Former Material / Material Interior de Bobina Móvil ………………………..Aluminum / Aluminio Winding Material / Material de Bobinado……………………………………………………………………….Copper / Cobre Cone Material / Material del Cono ………………………………………..Non-Pressed Paper / Papel no prensado Dust Cap Material/ Material de la tapa antipolvo ……………………………………………………………………………… PPI Surround Material / Material de la Suspension…………………………………………………………….. Foam / Espuma Basket Material / Material de la Canasta …………………………………………………………………………… Steel / Acero Magnet Material / Material del Imán……………………………………………………………………………… Ferrite / Ferrito Magnet Weight / Peso del imán……………………………………………………………………………………………………….50 Oz
BOX SPECIFICATIONS / ESPECIFICACIONES DE LA CAJA:
Internal Volume / Volumen Interno………………………………………………………………………………………0.3ft3 / 8.5L Load Configuration / Cargar configuración …………………………………………………………………Parallel / Paralelo Box Type / Tipo de caja…………………………………………………………………………………………………….Sealed / Sellado Box Material / Material de la caja …………………………………………………. Polyethylene (PE) / Polietileno (PE) Finish Material / Material de acabado………………………………………………………………………………..Black / Negro -3Db Dropping Point (F3) / -Punto de caída 3Db (F3)…………………………………………………………………….42Hz
MEASUREMENT / ESPECIFICACIONES DE LA CAJA:
Overall Height / Altura Total ………………………………………………………………………………………………6″ / 152.4mm Overall Width / Ancho Total ……………………………………………………………………………………………. 14.6″ / 372mm Overall Depth / Profundidad Total …………………………………………………………………………………….7.2″ / 183mm
MEASUREMENTS / MEDIDAS:
0.67″ / 17mm
7.11″ / 180.60mm
7.27″ / 184.67mm
15.01″ / 381.16mm
MEASUREMENTS / MEDIDAS:
2-M8
7.27″ / 184.65mm
2-Ø0.51″ / 13mm
1.18″ / 30mm 4.19″ / 106.50mm
WARRANTY
Please visit our website DS18.com for more information on our warranty policy.
We reserve the right to change products and specifications at any time without notice. Images may or may not included optional equipment.
WARNING:
Cancer and Reproductive Harm. www.P65Warning.ca.gov
GARANTÍA
Visita nuestra página web DS18.com para obtener más información sobre nuestra garantía.
Nos reservamos el derecho de cambiar productos y especificaciones en cualquier momento sin previo aviso. Las imágenes pueden incluir o no equipo opcional.
ADVERTENCIA:
Cáncer y Daño Reproductivo. www.P65Warning.ca.gov
FOR MORE INFORMATION PLEASE VISIT DS18.COM
V1
Official DS18 Pro Audio Store - Speakers, Subwoofers, Amps & More!
