491105 Wall-Mounted EV Wallbox Charger
Product Information
The EV Wallbox is a wall-mounted charger designed for charging
electric vehicles. It comes in two modes: Mode A and Mode C. The
product reference number is p.n.491105. The package includes the EV
Charging Station, a plate, a hook, reference paper, 30mm plastic
bolts, screw shims, 30mm screws, 95mm screws, 30mm metal bolts, and
the necessary tools for installation (electric drill, hammer,
screwdriver).
Mode A Installation Instructions
- Hammer the 30mm plastic bolts into the wall.
- Drill the necessary holes.
- Take down the reference paper.
- Fix the plate onto the wall using the 30mm screws.
- Place the EV Charging Station onto the plate.
- Remove the front board of the EV Charging Station.
- Fix the socket on the wall, connecting the wires correctly
based on the provided color codes (RED BROWN for 1 phase, RED BLUE
GREEN & YELLOW for 3 phase). - Fix the hook onto the wall using four plastic bolts.
- Remove the protective film from the EV Charging Station.
- Installation is completed.
Mode C Installation Instructions
- Drill the necessary holes.
- Hammer the 30mm plastic bolts into the wall.
- Take down the reference paper.
- Fix the plate onto the wall using the 30mm screws.
- Place the EV Charging Station onto the plate.
- Connect the wires correctly based on the provided color codes
(RED BLUE GREEN & YELLOW for 1 phase, RED BROWN GRAY BLUE GREEN
& YELLOW for 3 phase). - Fix the hook onto the wall using four plastic bolts.
- Remove the protective film from the EV Charging Station.
- Installation is completed.
Security Warning
Non-compliance with the operating instructions can cause serious
consequences. The manufacturer does not assume any liability for
damage caused by disregarding operating instructions or other
warnings marked on the device. This product is not suitable for
people with limited mobility, sensory or psychological
disabilities, and those who lack use experience or a certain degree
of knowledge.
Please do not use the EV Wallbox for purposes other than
electric car charging. Do not try to disassemble the device by
yourself under any circumstances as it may damage internal
precision parts and void your ability to apply for after-sales
service.
Contact Information:
Address: 19 Hayezira St. Industrial Zone Ramla 7255616
Fax: 03-5214524
Phone: 03-5575110
Technical Support: *2023
QUICK USE GUIDE
Wall-mounted charger
EV WALLBOX
p.n.491105
EV CHARGING STATION
(MODE A)
(MODE C)
CONTENT IN THE BOX cMODE A
PLATE
STATION
EV CHARGING STATION
REFERENCE PAPER
HOOK
30MM PLASTIC BOLTS (FOR PLATE AND HOOK)
×10
SCREW SHIM
×4
30MM SCREWS (FOR PLATE AND HOOK)
95MM SCREWS
30MM METAL BOLTS
×10
×4
×4
TOOLS NEEDED FOR INSTALLATION
ELECTRIC DRILL
HAMMER
SCREWDRIVER
Reference paper
Hammer the 30mm plastic bolts
Drill the holes
Take down the reference paper
Fix the plate with 30mm screws
Place station onto plate
5
6
Rmove the front board
Fix the socket on the wall
RED BROWN
GRAY BLUE GREEN & YELLOW
RED BLUE GREEN & YELLOW
7
1 PHASE
L N PE
3 PHASE
L1 L2 L3 N PE
Connect each wire correctly
Fix the hook with four plastic bolts
8
Remove the protective film Installation is completed
CONTENT IN THE BOX cMODE C
PLATE
STATION
EV CHARGING STATION
REFERENCE PAPER
HOOK
30MM PLASTIC BOLTS (FOR PLATE AND HOOK)
×10
30MM SCREWS (FOR PLATE AND HOOK)
×10
TOOLS NEEDED FOR INSTALLATION
ELECTRIC DRILL
HAMMER
SCREWDRIVER
Reference paper Drill the holes
Hammer the 30mm plastic bolts
Take down the reference paper
Fix the plate with 30mm screws
Place station onto plate
5
1 PHASE
RED BLUE GREEN & YELLOW
L N PE
3 PHASE
RED BROWN
GRAY BLUE GREEN & YELLOW
L1 L2 L3 N PE
Connect each wire correctly
Fix the hook with four plastic bolts
6
Remove the protective film Installation is completed
SECURITY WARNING
! ATTENTION Non-compliance with the operating instructions can cause serious consequences. Manufacturer does not assume any liability for damage caused by disregarding operating instructions or other warnings marked on the device. High voltage, fire hazard! Never use the device if the housing is damaged or opened! This product is not suitable for people with limited mobility, sensory or psychological disabilities, and those who lack use experience or a certain degree of knowledge.
! IMPORTANT SAFETY INSTRUCTIONS WARNING! ·This product should only be installed, repaired or maintained by authorized electricians and in accordance with national guidelines for electrical installations. All applicable local, regional and national regulations for electrical installations must be respected. ·Regularly check if the charger has visible damage. Do not use a damaged product. ·Make sure that all safety facilities and connections are available, properly installed and undamaged at all times and are tested regularly to ensure they can operate normally. ·Make sure that the input voltage, frequency, circuit breakers and other conditions of the device meet the specifications before the device is powered on. It’s important to observe the maximum permissible charging current of the connection. ·Before powering on the device, please confirm that the device is properly grounded to avoid unnecessary accidents. If a ground fault occurs, it is assumed that the cable carries voltage. Please make sure there is no high-voltage power in the system before inspecting the device. ·Please insulate the unnecessarily exposed metal parts of all tools to prevent them from touching the metal frame, which may cause short circuit. ·To ensure the service life and stable operation of the charging station, the operating environment should be kept as clean as possible with a relatively stable temperature and humidity. The charging station must not be used in flammable environment or environments with volatile gas. ·Please keep the power cord away from the heated surface. Please do not put the power cord in the gap of the closed door or pull it out of sharp edges or corners. ·Do not use the charger when the inside of the charging plug is wet. ·Do not modify, retrofit, or change any part by yourself under any circumstances. ·Please do not use this product as a toy. Pls. take good care of children to ensure that they will not play with this device as a toy nor put fingers into the charging connector when the power plug is still connected.
·The circuit to which the charger is to be connected must be equipped with a residual current circuit breaker.
! Note Please do not use it for other purposes except electric car charging. Do not try to disassemble the device by yourself under any circumstances. Otherwise, the internal precision parts may be damaged, and you will not be able to apply after-sales service.
19 Hayezira St. Industrial Zone Ramla 7255616 fax. 03-5214524 | phone: 03-5575110
Technical support *2023
