Boke Bk-dwl042 Independent Color Temperature Driver Owner's Manual

BK-DWL042 Independent Color Temperature Driver

BOKE Drivers Co., Ltd.

Constantcurrentindependentcolortemperaturedriver DWLSeriessuffixD(DALI-2+pushDIM+pushCCT)
Screw-free/pressing wiring box 10-level current output DALI-2/PUSH control Support 1.5mm2x5 or 2.5mm2x3 wire

Features – Support DALI-2+pushCCT control – 10-level current output can be realized through DIP-switch, easier to adjust the
luminaire power – Soft dimming and flicker-free at any brightness, meets the new requirements
of ErP certification – Using HPC patented technology, at any dimming level, the current output between drivers is the same – Dimming range 1%~100%, output current accuracy 1% – Standby power input<0.5W, meets the requirements of ErP certification – High PF, high efficiency, low THD – Screw-free and pressing type strain relief, easier install
Support 1.5mm2x5 or 2.5mm2x3 wire – Intelligent LED hot-plug protection function – SELV and Class II design, suitable for use outside of the light – Passed ENEC-TUV,CE,RCM,CCC,DALI-2 and other certifications – IP20 protection grade, indoor use – Nominal life-time up to 100,000 h – 5-year guarantee

Interfaces – DALI-2(DALI-2 DT8) – PUSH(pushDIM) – PUSH(pushCCT)
Functions – pushCCT with memory function(PUSH) – Support central emergency application (dimming normal in DC input – Support self-contained emergency application – Protective features (short-circuit, overload,no-load, hot plug-in protection )
Suitableforlights – Suitable for lights with independent drivers such as
downlights, spotlights, panel lights, etc – Not suitable for lights with built-in drivers
Typicalapplications – LED indoor lighting – LED office lighting – LED commercial lighting

[email protected]

FLICKER FREE

PUSH

CCT
Color temperature

1% Accuracy
Current

1% Lowest
dimming

Hot plug-in Protection

www.bokedriver.com

REV.1.1 2021-3-30 P1

BOKE Drivers Co., Ltd.

Modelcodingrulesof DWLseries

BK – D WL X X X – X X X X z

D

Function mode(D: DALI-2+pushDIM+pushCCT) Output load voltage range identification code Output current Product series BOKE

OrderselectiontableofDWLseries( justsuffixD,42-60W)

Model BK-DWL042-1050AD BK-DWL060-1500AD BK-DWL060-2000AD

Input voltage 200-240VAC 200-240VAC 200-240VAC

Output power 42.0W 63.0W 62.0W

Output voltage 12-42VDC 12-42VDC 12-42VDC

Output current
0.60-1.05A 1.05-1.50A 1.55-2.00A

Dimension L173.0*W75*H30mm L191.5*W75*H30mm L191.5*W75*H30mm

Article number B-DWL042-HA0100AD B-DWL060-HA0101AD B-DWL060-HA0100AD

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P2

BOKE Drivers Co., Ltd.

Technicaldata

Product model Output parameters Regulation method Rated output current Rated output voltage Rated output power Output current adjustment Output current ripple LF Output current accuracy

BK-DWL042-1050AD
Constant Current 0.6-1.05A 12-42V 42W Max
DIP S.W(10 levels) ±2% ±1%

Linear regulation Load regulation No load output voltage Flicker-free(typical) Input parameters

±1% ±1% 50V Modulation depth =0.089% (100 Hz), Pst LM = 0.01, SVM = 0.002,(The above parameters are obtained from testing the panel lights)

Rated input voltage Rated input voltage Input votage shock Input current Input frequency Input power factor Input THD Efficiency(typical) In-rush current Start/Switchover/Turn off

200-240VAC 200-240VDC 180-264VAC 180-264VDC <380 V AC, 1 h <0.3A (AC input) 47-63Hz >0.95 (230V AC & Full load) 10% (230V AC & Full load) 89% (230V AC & Full load) 8.25A peak ,206us duration(50 % Ipeak), see the description below for details <0.6s(AC start),<0.6s(DC start),<0.3s(AC/DC switchover),<0.5s(Turn off )

Switching cycles Power consumption Safety Withstand voltage Mains surge capability Leakage current Isolation resistance Control interface DALI dimming port PUSH dimming port 1-10V 3in1 dimming port

> 50,000 switching cycles Full load(Pmax):42W, No load(Pno): N/A, On stand-by(Psb) : <0.5W, Network stand-by(Pnet) : N/A
I/P-O/P:3750V AC, I/P-DALI: 500V AC. L-N:2KV <0.7mA (230V AC & Full load) I/P-O/P:100M/500Vdc/25/70% RH
Voltage range: 9.5-22.5V, typical 16V, interface current consumption: 1.8mA Voltage range: 180-264V 47/63Hz N/A

Auxiliary power supply Dimming range Dimming drive mode

N/A 1-100% AM(amplitude modulation)

Emergency support Central emergency system Self-contained emergency

Supported(dimming normal in DC input) Supported

Environment & Life time

Operating temperature Case temperature Operating humidity Storage temp./humidity IP grade MTBF

Ta=-20-50 Tc=85 5-85% RH, not condensed -40-80, 5-85% RH, not condensed IP20 500,000H,MIL-HDBK-217F(25)

Life-time Vibration resistant Acoustic Noise Environmental protection

Nominal life-time up to 100,000 h, see the description below for details 10~500Hz,5G 12min./1cycle,period for 72min. each along X,Y,Z axes <25dB(30cm, Full load) RoHS

Certifications and standards

Certified Safety EMC

ENEC-TUV, RCM, EMC, CE, CCC, DALI-2 EN61347-1, EN61347-2-13, EN62384 EN55015, EN61000-3-2 , EN61000-3-3, EN61000-4-2,3,4,5,6,8,11, EN61547

DALI-2 EL RF

IEC 62386-101(DALI-2), IEC 62386-102(DALI-2), IEC 62386-207(DALI-2), IEC 62386-209(DALI-2) N/A N/A

Remarks
1.By default, all parameter are measured at 230V AC input, full load and 25 of ambient temperature. 2.The driver can not be installed inside the light. when the driver is used with the light, the EMC of the whole light needs to be tested.

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P3

BOKE Drivers Co., Ltd.

Technicaldata

Product model Output parameters Regulation method Rated output current Rated output voltage Rated output power Output current adjustment Output current ripple LF Output current accuracy

BK-DWL060-1500AD
Constant Current 1.05-1.5A 12-42V 63W Max
DIP S.W(10 levels) ±2% ±1%

BK-DWL060-2000AD
Constant Current 1.55-2A 12-42V 62W Max
DIP S.W(10 levels) ±2% ±1%

Linear regulation Load regulation No load output voltage Flicker-free(typical) Input parameters

±1%

±1%

±1%

±1%

50V

50V

Modulation depth =0.040% (100 Hz), Pst LM = 0.015, SVM = 0.01,(The above parameters are obtained from testing the panel lights)

Rated input voltage Rated input voltage Input votage shock Input current Input frequency Input power factor Input THD Efficiency(typical) In-rush current Start/Switchover/Turn off

200-240VAC 200-240VDC 180-264VAC 180-264VDC <380 V AC, 1 h <0.45A (AC input) 47-63Hz >0.95 (230V AC & Full load) 10% (230V AC & Full load) 90% (230V AC & Full load) 11.4A peak ,190us duration(50 % Ipeak), see the description below for details <0.6s(AC start),<0.6s(DC start),<0.3s(AC/DC switchover),<0.5s(Turn off )

Switching cycles Power consumption Safety Withstand voltage Mains surge capability Leakage current Isolation resistance Control interface DALI dimming port PUSH dimming port 1-10V 3in1 dimming port

> 50,000 switching cycles Full load(Pmax):66W, No load(Pno): N/A, On stand-by(Psb) : <0.5W, Network stand-by(Pnet) : N/A
I/P-O/P:3750V AC, I/P-DALI: 500V AC. L-N:2KV <0.7mA (230V AC & Full load) I/P-O/P:100M/500Vdc/25/70% RH
Voltage range: 9.5-22.5V, typical 16V, interface current consumption: 1.8mA Voltage range: 180-264V 47/63Hz N/A

Auxiliary power supply Dimming range Dimming drive mode

N/A 1-100% AM(amplitude modulation)

Emergency support Central emergency system Self-contained emergency

Supported(dimming normal in DC input) Supported

Environment & Life time

Operating temperature Case temperature Operating humidity Storage temp./humidity IP grade MTBF

Ta=-20-50 Tc=85 5-85% RH, not condensed -40-80, 5-85% RH, not condensed IP20 500,000H,MIL-HDBK-217F(25)

Life-time Vibration resistant Acoustic Noise Environmental protection

Nominal life-time up to 100,000 h, see the description below for details 10~500Hz,5G 12min./1cycle,period for 72min. each along X,Y,Z axes <25dB(30cm, Full load) RoHS

Certifications and standards

Certified Safety EMC

ENEC-TUV, RCM, EMC, CE, CCC, DALI-2 EN61347-1, EN61347-2-13, EN62384 EN55015, EN61000-3-2 , EN61000-3-3, EN61000-4-2,3,4,5,6,8,11, EN61547

DALI-2 EL RF

IEC 62386-101(DALI-2), IEC 62386-102(DALI-2), IEC 62386-207(DALI-2), IEC 62386-209(DALI-2) N/A N/A

Remarks
1.By default, all parameter are measured at 230V AC input, full load and 25 of ambient temperature. 2.The driver can not be installed inside the light. when the driver is used with the light, the EMC of the whole light needs to be tested.

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P3

BOKE Drivers Co., Ltd.

Electricalvalues BK-DWL042-1050AD Operating window

Output voltage (V)

Eficiency (%)

50 40 30 20 10 00
0

600

700

800

900

1000

1100

Output current(mA) Efficiency vs load

Operating window 100 % Operating window dimmed

90.00 89.00 88.00 87.00 86.00 85.00 84.00 83.00 82.00 81.00 80.00 79.00 78.00 77.00 76.00 75.00 74.00 73.00 72.00 71.00 70.00

10% 1.05A

20% 1A

30% 0.95A

40% 0.9A

50% 0.85A

60% 0.8A

70% 0.75A

80% 0.7A

90% 0.65A

100% 0.6A

Load(%)

Power factor vs. Load

1.000 0.980 0.960 0.940 0.920 0.900 0.880 0.860 0.840 0.820 0.800 0.780 0.760 0.740 0.720 0.700

10% 1.05A

20% 1A

30% 0.95A

40% 0.9A

50% 0.85A

60% 0.8A

70% 0.75A

80% 0.7A

90% 0.65A

100% 0.6A

PF

Load(%)

Output voltage (V)

BK-DWL060-1500AD Operating window

50 40 30 20 10 00
0

1050 1150 1250 1350 1450

1550

Output current(mA)

Operating window 100 % Operating window dimmed

Output current (mA)

THD

Output current (mA)

Operating window

1200 1000
800 600 400 200
00 0 5 10 15 20 25 30 35 40 45

Output power(W) THD vs. Load

Operating window 100 % Operating window dimmed

55.0

45.0

35.0

25.0

15.0

5.0 10% 20% 30% 40% 50% 60% 70% 80% 90% 100%

1.05A

1A

0.95A 0.9A 0.85A 0.8A 0.75A 0.7A 0.65A 0.6A

Load(%)

Operating window

1800

1500

1200

900

600

300

00

0

8

16

24

32

40

48

56

64

Output power(W)

Operating window 100 % Operating window dimmed

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P5

Eficiency (%)

PF

BOKE Drivers Co., Ltd.

BK-DWL060-1500AD(Continue) Efficiency vs load

95.0 90.0 85.0 80.0 75.0 70.0 65.0 60.0
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 1.5A 1.45A 1.35A 1.30A 1.25A 1.20A 1.15A 1.10A 1.05A

Load(%)

Power factor vs. Load

1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450
10%
1.5A

20% 1.45A

30% 1.40A

40% 1.35A

50% 1.30A

60% 1.25A

70% 1.20A

80% 1.15A

90% 1.10A

100% 1.05A

Load(%)

BK-DWL060-2000AD

Operating window

50 40 30 20 10 00
0

1550 1650 1750 1850 1950

2050

Output current(mA)

Operating window 100 % Operating window dimmed

Efficiency vs load
90.0 85.0 80.0 75.0 70.0 65.0 60.0
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 2A 1.95A 1.85A 1.8A 1.75A 1.7A 1.65A 1.6A 1.55A
Load(%)

THD

Output current (mA)

THD

THD vs. Load
65 55 45 35 25 15 5
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 1.5A 1.45A 1.40A 1.35A 1.30A 1.25A 1.20A 1.15A 1.10A 1.05A
Load(%)

Operating window

2500

2000

1500

1000

500

00

0

10

20

30

40

50

60

70

Output power(W)

Operating window 100 % Operating window dimmed

THD vs. Load
65 55 45 35 25 15 5
10% 20% 30% 40% 50% 60% 70% 80% 90% 100% 2A 1.95A 1.9A 1.85A 1.8A 1.75A 1.7A 1.65A 1.6A 1.55A
Load(%)

Output voltage (V)

Eficiency (%)

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P6

BOKE Drivers Co., Ltd.

PF

BK-DWL060-1500AD(Continue) Power factor vs. Load

1.000 0.950 0.900 0.850 0.800 0.750 0.700 0.650 0.600 0.550 0.500 0.450

10% 20% 2A 1.95A

30% 40% 1.9A 1.85A

50% 60% 1.8A 1.75A

70% 80% 1.7A 1.65A

90% 1.6A

100% 1.55A

Load(%)

Expectedlife-time BK-DWL042-1050AD Life-time vs. case temperature

110,000 100,000 90,000 80,000 70,000 60,000 50,000 40,000 30,000 20,000

50

55

60

65

70

75

80

85

90

Case temperature(Tc)

BK-DWL060-2000AD
Life-time vs. case temperature
110,000 100,000 90,000 80,000 70,000 60,000 50,000 40,000 30,000 20,000
50 55 60 65 70 75 80 85 90
Case temperature(Tc)

Life-time(H)

BK-DWL060-1500AD Life-time vs. case temperature
110,000 100,000 90,000 80,000 70,000 60,000 50,000 40,000 30,000 20,000
50 55 60 65 70 75 80 85 90
Case temperature(Tc)
-The life-time of the LED driver is shown in the figure above (calculated based on the 90% survival rate). – The relation of tc to ta temperature depends also on the luminaire design.

Life-time(H)

Life-time(H)

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P7

BOKE Drivers Co., Ltd.

Surge

Model

Ipeak Twidth Condition

B10 B13

B16 B20 B25

Relative number of MCB C10 C13 C16 C20 C25

D10 D13

D16 D20 D25

BK-DWL042-1050AD 8.25A 206us BK-DWL060-1500AD 11.4A 190us BK-DWL060-2000AD 11.1A 188us

AC 230V,Full load, Cold start,Ta30, MCB is not installed side by side

33pcs 43pcs 52pcs 65pcs 82pcs 33pcs 43pcs 52pcs 65pcs 82pcs 33pcs 43pcs 52pcs 65pcs 82pcs 22pcs 29pcs 36pcs 45pcs 56pcs 22pcs 29pcs 36pcs 45pcs 56pcs 22pcs 29pcs 36pcs 45pcs 56pcs 23pcs 30pcs 36pcs 45pcs 57pcs 23pcs 30pcs 36pcs 45pcs 57pcs 23pcs 30pcs 36pcs 45pcs 57pcs

Ipeak

Twidth

50% Ipeak

Remarks
– The number of drives mounted under different MCBs in the table is the maximum value. Please do not exceed this number during installation.
– Calculation uses typical values from ABB series S200 as a reference. – Different brands and models of miniature circuit breakers, the number of drives
mounted will be slightly different. – If the ambient temperature of the MCB installation exceeds 30°C or multiple MCBs
are installed side by side, the number of drives mounted will be reduced and the
calculation needs to be recalculated. – Electrician’s usually consider Type B for household lighting and Type C for commercial
lighting application.

Functions Outputshort-circuitbehaviour – In case of a short-circuit at the LED output ,the LED output is switched off. – After restart of the LED driver ,the output will be activated again. – The restart can either be done via mains reset or via interface (DALI, PUSH-DIM). Outputno-loadoperation – The LED driver will not be damaged in no-load operation. – The output will be deactivated and is therefore free of voltage. – If a LED load is connected the device has to be restarted before the output will be activated again. – The restart can either be done via mains reset or via interface (DALI, PUSH-DIM). Outputoverloadprotection – If the output voltage range is exceeded the LED driver turns off the LED output. – After restart of the LED driver the output will be activated again. – The restart can either be done via mains reset or via interface (DALI, PUSH-DIM). Outputhotplug-in – Plug the LED into the output of the powered driver. For protection LED, the LED will not on, The device has to be restarted. – This can be done via mains reset or via interface (DALI). Tunablewhitefunctionality – This driver have 2 output channels used to control the intensity and temperature of white colour as well known as “Tunable White”. – These drivers respond to DALI type 8 (DT8) commands, which in practice means that they only have 1 common address for both output channels . – The tunable white level of intensity and colour temperature can be set either with a DALI command or by PUSH switch control. – The driver will operate correctly once tunable white LED module parameters are programmed to the driver. Use the DALI tools for the parameter setting. – The higher the brightness, the wider the color temperature range can be obtained.

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P8

BOKE Drivers Co., Ltd.

DIP-switch&outputcurrent

BK-DWL042-1050AD

Pin
29.0W 31.0W 33.5W 36.0W 38.0W 40.5W 43.0W 45.0W 47.5W 47.5W

Irated
600mA 650mA 700mA 750mA 800mA 850mA 900mA 950mA 1000mA 1050mA

Voltage 1

2

3

4

42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 40VDC

ON ON ON

ON — ON ON

– –

— ON ON

— ON — ON

– –

– –

— ON

ON ON ON —

— — ON —

— ON —

– –

ON —

– –

– –

– –

– –

– –

– –

BK-DWL060-1500AD

Pin
50.0W 52.0W 54.5W 57.0W 59.5W 61.5W 64.0W 66.5W 69.0W 70.5W

Irated
1050mA 1100mA 1150mA 1200mA 1250mA 1300mA 1350mA 1400mA 1450mA 1500mA

Voltage 1

2

3

4

42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 42VDC 42VDC

— ON ON ON

ON — ON ON

– –

— ON ON

— ON — ON

– –

– –

— ON

ON ON ON —

— — ON —

— ON —

– –

ON —

– –

– –

– –

– –

– –

– –

BK-DWL060-2000AD

Pin
73.0W 72.0W 74.5W 73.0W 71.0W 71.0W 71.0W 71.0W 71.0W 70.5W

Irated
1550mA 1600mA 1650mA 1700mA 1750mA 1800mA 1850mA 1900mA 1950mA 2000mA

Voltage 1

2

3

4

42VDC 40VDC 40VDC 38VDC 36VDC 35VDC 34VDC 33VDC 32VDC 31VDC

ON ON ON

ON — ON ON

– –

— ON ON

— ON — ON

– –

– –

— ON

ON ON ON —

— — ON —

— ON —

– –

ON —

– –

– –

– –

– –

– –

– –

Remarks: 1. It means that this item is the factory default current.
— 2. It means that this channel is OFF.

Label

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P9

BOKE Drivers Co., Ltd.

DALIdimmingapplication Wiring diagram

DWL driver

WW+ WWCW+ CW-
DA DA PUSH AC/N AC/L

DWL driver

WW+ WWCW+ CW-
DA DA PUSH AC/N AC/L

+
Warm white LED string
+
Cool white LED string
–
+
Warm white LED string
+
Cool white LED string
–

Note: The voltage deviation of warm white and cool white light strings should be less than 0.5V

DA DA ACL ACN FG(optional)
Max. x64

ActivatingDALIcontrolmode – After installation according to the wiring diagram of DALI control application,the driver will automatically switch to the DALI control mode after receiving any DALI command.

Remarks: – Standard DALI control line voltage range:9.5V to 22.5V ,type 16V. – The two DALI control lines polarity-reversible. – Max. 64 DALI drivers per DALI control line. – The maximum distance length of the DALI control line is 300m at 2×1.5mm2. – DALI bus can be wired together with any mains voltage cables, but separate
wiring is recommended.

Wiringdistancevscablesize

Cable size

Distance

2×0.50mm2

max.100m

2×0.75mm2

max.150m

2×1.00mm2

max.200m

2×1.50mm2

max.300m

Dimmingcurve

Output current(%)

100% 90% 80% 70% 60% 50% 40% 30% 20% 10% 0%
0

Logarithmic dimmer curve
50 100 150 200 254 dimming level

Remarks: The dimming curve can be selected by DALI configuration. The default is logarithmic dimming curve.

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P10

BOKE Drivers Co., Ltd.

PUSHdimmingapplication Wiring diagram

DWL driver

WW+ WWCW+ CW-
DA DA PUSH AC/N AC/L

DWL driver

WW+ WWCW+ CW-
DA DA PUSH AC/N AC/L

+
Warm white LED string
+
Cool white LED string
–

PUSH CCT switch

PUSH dimming switch

ACL ACN FG(optional)

+
Warm white LED string
+
Cool white LED string
–

Note: The voltage deviation of warm white and cool white light strings should be less than 0.5V

Max. x50

ActivatingPUSHcontrolmode – After installation according to the wiring diagram of PUSH-DIM control application, short press the PUSH dimmming switch(PUSH-DIM port) 5 times within 3 seconds, the driver will automatically switch to PUSH control mode. PUSHdimmingswitchoperatinginstructions – Turn on or turn off: short press PUSH dimming switch for 0.2-1s. – Stepless dimming : long press PUSH dimming switch for 1-6s, Press again to switch dimming directions. PUSHCCTswitchoperatinginstructions – Switch CCT level: short press PUSH CCT switch for 0.2-1s9 levels of preset CCT can be switched. – Stepless CCT adjustment: long press CCT PUSH switch for 1-6s,Press again to switch CCT adjustment directions. Poweronstatus: – After power on,the light state will be the same as the last dimming level and the last CCT level. – If the light is on before the power is turned off, after turning the power back on, the brightness will be the same as the last time, and the color temperature will be the same as the last time. – If the light is off before the power is turned off, the light will be turned off after the power is turned back on. You need to press the PUSH-DIM dimming switch for a short time to turn on the light. The brightness after lighting will be the same as the last time, and the color temperature will be the same as the last time.

A%(BRI) B%(CCT)
before power off

Power off then power on

A%(BRI) B%(CCT)
After power on

A%(BRI) B%(CCT)
before power off

Short press PUSH-DIM switch

0%(BRI) —(CCT)
before power off

Power off then power on

0%(BRI) —(CCT)
after power on

Short press PUSH-DIM switch

A%(BRI) B%(CCT)
after press PUSH dimming switch

Multiplelightssynchronizecontroloperation method 1 Step 1:long press the PUSH-DIM switch,confirm each light is on. Step 2:short press the PUSH-DIM switch,confirm each light is off. Step 3:long press the PUSH-DIM switch,confirm each light is from darkest to brightest and all the lights are synchronous. method 2 – Long press the PUSH-DIM dimming switch for more than 15s, all drivers will output 100% brightness and the color temperature is natural white (middle of color temperature range).

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P11

BOKE Drivers Co., Ltd.

Installation
Mechanicaldimensions Unit:mm DWL042

173.5mm 162.5mm

75.0 mm 63.5 mm

2-4.2

DWL060

191.5 mm 180.5 mm

75.0 mm 63.5 mm

2-4.2

30mm

30mm

INPUT

Input wire

OUTPUT

Output wire

Pin Numbering 1 2 3 4 5 6

function FG DA DA
PUSH ACN ACL

Installationnote

colour black gray gray gray Orange Orange

0.75-2.5mm2 9-10mm

Pin Numbering function

1

WW+

2

WW-

3

CW+

4

CW-

colour red black red black

0.5-1.5mm2 8-9mm

Hotplug-in

Mountingscrewspecificationsandtorque

– Hot plug-in is not supported due to residual output voltage of > 0 V. – If a LED load is connected the device has to be restarted. – This can be done via mains reset or via interface (DALI).
Wiringguidelines
– All connections must be kept as short as possible to ensure good EMI behaviour. – Mains leads should be kept apart from LED Driver and other leads (ideally 5 10 cm distance) – Max. lenght of output wires is 2 m. – Incorrect wiring can damage LED modules. Installation requirements

– Max. torque at the clamping screw: 0.5 Nm / M4
LEDmodule – The voltage deviation of warm white and cool white light strings
should be less than 0.5V
ReplaceLEDmodule
1. Mains off 2. Remove LED module 3. Wait for 5 seconds 4. Connect LED module again

-Thedrivershouldbeinstalledinadry,acid-free,oil-free,fat-freeenvironment.

– The installation ambient temperature of the drive shall not exceed the value of Ta at any time.

-Thedrivershouldkeepacertaindistancefromtheheatingstuff(suchastheluminaireradiator).

– If the driver is used externally (it needs to be used with the accessories), the installation of the driver should also meet the following conditions: 1.The driver should be a certain distance between the drivers, as shown in Figure 1. 2.The driver keeps a certain distance from surrounding objects, as shown in Figure 2.

15cm

10mm
15cm 15cm

15cm

70mm

20mm

[email protected]

Figure 1

www.bokedriver.com

Figure 2 REV.1.1 2021-3-30 P12

Packaging

BOKE Drivers Co., Ltd.

Product

Model

Product size

DWL042 L173*W75*H30mm

DWL060 L191.5*W75*H30mm

Weight 225g 255g

Packaging
Packaging size L185*W38*H80mm L225*W38*H82mm

18pcs×2layer=36pcs/CIN 16pcs×2layer=32pcs/CIN

Carton size

Qty/carton N.W

G.W

L390*W365*H180mm

36pcs

8.10kg 10.0kg

L465*W325*H185mm

32pcs

8.20kg 10.2kg

Additionalinformation
1. This product can only be used outside the light body, Can not be used inside of the light, and it must be used within the specified working environment. 2. The life and MTBF of the product are for reference only, and do not represent a warranty statement. 3. For more information, please send an email to [email protected].

[email protected]

www.bokedriver.com

REV.1.1 2021-3-30 P13