Keyence Lbee5hy1mw Wifi Module Installation Guide

LBEE5HY1MW WiFi Module

Product Information

Product Usage Instructions

Antenna Design

Please perform the antenna design that follows the
specifications of the antenna. The signal line between the antenna
and the module should be a 50-ohm line design. Fine tuning of
return loss, etc. can be performed using a matching network.
However, it is required to check Class1 change and Class2 change as
defined by the authorities.

The concrete contents of the check are as follows:

1. It is the same type as the antenna type of antenna
   specifications.
2. An antenna gain is lower than a gain given in antenna
   specifications.
3. The emission level is not getting worse.

Theory of Operation-Channel List

The product operates in the following frequency bands and
modes:

Theory of Output Power List

The product has limited output power settings for different
modes:

LBEE5HY1MW Installation Manual
FCC ID of this product is as follows. FCC ID: RF41675A
IC No. of this product is as follows. IC: 5798A-1675A
Contents 1. Land Pattern (Recommended) 2. PIN Layout 3. Antenna 4. Supply Voltage and Operating Temperature 5. Theory of Operation-Channel List 6. Theory of Output Power List

1 / 14

1.

Land Pattern (Recommended)

2 / 14 Unit : mm

2.

PIN Layout

3 / 14

3.

Antenna

4 / 14

Please perform the antenna design that followed the specifications of the antenna. About the signal line between an antenna and a module It is a 50-ohm line design. Fine tuning of return loss etc. can be performed using a matching network. However, it is required to check “Class1 change” and “Class2 change” which the authorities define then.

The concrete contents of a check are the following three points. 1) It is the same type as the antenna type of antenna specifications. 2) An antenna gain is lower than a gain given in antenna specifications. 3) The emission level is not getting worse.

50-ohm line(microstrip line length)
Antenna

Antenna type

PCB antenna (Monopole antenna)

50-ohm feed line length

We test it at 0mm as a representative

Recommended antenna design

This Antenna Specification is based on Keyence’s requirement..

Model name LBEE5HY1MW

· Antenna Model Name

: ANT16244DT

· Antenna type

: PCB antenna (Monopole antenna)

· Antenna manufacture

: TDK Corporation

· Antenna gain

: +2.1 dBi @2442MHz

+3.5 dBi @5150MHz

· Frequency

: 2400-2483.5MHz, 5150-5850MHz

5 / 14

Recommended antenna characteristics

6 / 14

4.

Supply Voltage

7 / 14

Parameter

Operating Temperature*1

Supply Voltage

VBAT VIO*2 1.8V/3.3V

Min.

Typ.

Max.

Unit

-30

25

+85

deg.C

3.2

3.3

4.8

V

1.62

–

3.63

V

*1: Surface temperature of the shield case Functionality is guaranteed but specifications require derating at extreme temperatures
*2: VIO don’t influence the RF characteristic. Tolerance of 1.8V and 3.3V is ±10%.

5.

Theory of Operation-Channel List

Theory of Operation-Software Security and Channel List Frequency of operation

2.4GHz

11b/g/n (HT20)

2412-2462MHz

BT

2402-2480MHz

W52

11a/n ((V)HT20)

5180-5240MHz

W53

11a/n ((V)HT20)

5260-5320MHz

Scan Active N/A Active Passive

Ad-hoc mode Yes N/A Yes No

* This specification is limited to use in the above frequency bands and modes. Notes: End users cannot modify the software because F/W & driver are installed in device.

6.

Theory of Output Power List

This specification is limited to use with the following output power settings.

8 / 14

Limited output power setting. [dBm]

2.4GHz WLAN

Mode

Rate 1ch 2ch 3ch 4ch 5ch 6ch 7ch 8ch 9ch 10ch 11ch

1M

14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0

IEEE

2M

14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0

802.11b 5.5M 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0

11M 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0 14.0

6M

10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

9M

10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

12M 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

IEEE 802.11g

18M 24M

10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

36M 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

48M 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

54M 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

MCS0 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

MCS1 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

MCS2 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

IEEE

MCS3 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

802.11n MCS4 10.0 10.0 13.0 13.0 13.0 13.0 13.0 13.0 13.0 10.0 10.0

MCS5 10.0 10.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 10.0 10.0

MCS6 10.0 10.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 10.0 10.0

MCS7 10.0 10.0 12.0 12.0 12.0 12.0 12.0 12.0 12.0 10.0 10.0

5GHz WLAN

Mode

Rate

6M

9M

12M

IEEE

18M

802.11a

24M

36M

48M

54M

MCS0

MCS1

IEEE 802.11n (HT20)

MCS2 MCS3 MCS4 MCS5

MCS6

MCS7

36ch 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0

40ch 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0

44ch 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0

48ch 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0

52ch 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0

56ch 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0 11.0

60ch 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0

64ch 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0 10.0

LBEE5HY1MW User Manual for FCC

9 / 14

Regarding FCC modular approval of LBEE5HY1MW Model Name: LBEE5HY1MW FCC ID: RF41675A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure).
The following information must be indicated on the host device of this module.
Contains Transmitter Module FCC ID: RF41675A or Contains FCC ID: RF41675A
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
*If it cannot be described on the host product, it must be listed on both the host product manual and on the host product package or removable label.

10 / 14 The following statements must be described on the user manual of the host device of this module; FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Compliance with FCC requirement 15.407(c) Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure.
Frequency Tolerance: ±20 ppm
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
When installing it in a mobile equipment. Please describe the following warning to the manual. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body.
When installing it in a portable equipment. Please describe the following warning to the manual. The available scientific evidence does not show that any health problems are associated with using low power wireless devices. There is no proof, however, that these low power wireless devices are absolutely safe. Low power Wireless devices emit low levels of radio frequency energy (RF) in the microwave range while being used. Whereas high levels of RF can produce health effects (by heating tissue), exposure of low-level RF that does not produce heating effects causes no known adverse health effects. Many studies of low-level RF exposures have not found any biological effects. Some studies have suggested that some biological effects might occur, but such findings have not been confirmed by additional research. LBEE5HY1MW has been tested and found to comply with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines.
It is necessary to take a SAR test with your set mounting this module (except to use only Bluetooth V5.0(BDR/EDR/LE)). Class II permissive change application is necessary using the SAR report.

Note)

11 / 14

Portable equipment: Equipment for which the spaces between human body and antenna are used within

20cm.

Mobile equipment: Equipment used at position in which the spaces between human body and antenna

exceeded 20cm.

LBEE5HY1MW User Manual for ISED

12 / 14

PMN: LBEE5HY1MW HVIN: LBEE5HY1MW IC Number: 5798A-1675A
Since this module is not sold to general end users directly, there is no user manual of module. For the details about this module, please refer to the specification sheet of module. This module should be installed in the host device according to the interface specification (installation procedure).
The following information must be indicated on the host device of this module.
Contains IC: 5798A-1675A
The following statements must be described on the user manual of the host device of this module;
This device complies with Industry Canada’s applicable licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: 1) l’appareil ne doit pas produire de brouillage; 2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User’s manual.
In case of the final product which can be carried around to outdoor.
The following indication is necessary to the final product. When the AP function is used in W52; At the time of a channel setting of W52, please indicate “for indoor use only”. During connecting, please
show the channel number which connects. And please indicate that the end user may find out “for indoor use only channel”.

13 / 14 When the STA function is used in channel 52, 54, 58, at the time of the channel 52 or 54 or 58 setting, please indicate “for indoor use only channel”. During connecting, please show the channel number which connects. And please indicate that the end user may find out “for indoor use only channel”.

If the antenna of the end product is removed, please describe the follow warning on the manual of the end product which contains this module.

This radio transmitter (IC Number: 5798A-1675A) identify the device by certification number or model

number if Category II) has been approved by Industry Canada to operate with the antenna types listed

below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain

greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

: 2.4GHz

Monopole Gain: +2.1 dBi

: 5GHz

Monopole Gain: +3.5 dBi

Le présent émetteur radio (IC Number: 5798A-1675A) a été approuvé par Industrie Canada pour

fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal. Les

types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué, sont

strictement interdits pour l’exploitation de l’émetteur.

Type d’antenne

: 2.4GHz

Monopole Gain: +2.1 dBi

: 5GHz

Monopole Gain: +3.5 dBi

If the final product use the following frequency, please note that there is a limit.

For indoor use only (5150-5250MHz band and channel 52, 54, 58) Pour usage intérieur seulement (5150-5250MHz band and channel 52, 54, 58)

14 / 14 The following statements must be described on the user manual of the host device of this module;
Data transmission is always initiated by software, which is the passed down through the MAC, through the digital and analog baseband, and finally to the RF chip. Several special packets are initiated by the MAC. These are the only ways the digital baseband portion will turn on the RF transmitter, which it then turns off at the end of the packet. Therefore, the transmitter will be on only while one of the aforementioned packets is being transmitted. In other words, this device automatically discontinue transmission in case of either absence of information to transmit or operational failure. La transmission des données est toujours initiée par le logiciel, puis les données sont transmises par l’intermédiaire du MAC, par la bande de base numérique et analogique et, enfin, à la puce RF. Plusieurs paquets spéciaux sont initiés par le MAC. Ce sont les seuls moyens pour qu’une partie de la bande de base numérique active l’émetteur RF, puis désactive celui-ci à la fin du paquet. En conséquence, l’émetteur reste uniquement activé lors de la transmission d’un des paquets susmentionnés. En d’autres termes, ce dispositif interrompt automatiquement toute transmission en cas d’absence d’information à transmettre ou de défaillance.
*If it is difficult to describe this statement on the host product due to the size, please describe in the User’s manual.
When installing it in a mobile equipment. Please describe the following warning to the manual.
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping the radiator at least 20cm or more away from person’s body. Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques (RF) CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou plus entre le radiateur et le corps humain.