FF-BRSG Blue Ridge Bent Back Glider
Product Information
The Blue Ridge Bent Back Glider is a product of Buck Stove, New
Buck Corp. The product dimensions are not mentioned in the user
manual. The package includes all the necessary hardware and parts
required for assembly.
Included Hardware
- 2.5in Bolt 4PCS
- 3in Bolt 2PCS
- 3.5in Bolt 4PCS
- Washer 18PCS
- Nut 10PCS
- 1.25in Screw
- 2in Screw 8PCS
- 1in Screw
Hardware without piece count comes preinstalled.
Included Parts
- Arm/Leg Assembly
- Back Assembly
- Seat Assembly
- Rear Cover Strip
- Glide Assembly
- Front/Rear Brace
Required Tools
- 7/16 Socket Wrench
- 1/2 Socket
- 7/16 Wrench
- 1/2 Wrench
- #2 Square Bit
Product Usage Instructions
Step 1:
Unscrew the loosely attached 1.25 in(F) & 1 in(N) screws,
and remove the rear cover strip (K) and place aside for final
assembly.
Step 2:
Begin the assembly process by placing the glider in the
orientation shown in the user manual, with the back (I) and seat
assembly (J) on their side.
Step 3:
Align the holes on the arm assembly (H) with the holes going
through the back (I) and seat assemblies(J).
Step 4:
Insert the 3.5 inch bolt (C) through a washer (D) and into the
leg/arm (H), back (I) and seat (J) assemblies.
Step 5:
Insert the 2.5 inch bolt (A) through a washer (D) and into the
leg/arm (H) and seat (J) assemblies.
Step 6:
On the back side of the bolts (A & C) that were inserted
through the seat (J), place a washer and then thread a nut onto all
of the bolts placed in steps 3-4. Tighten with 7/16 socket and
wrench.
Step 7:
Place the 3 inch bolt (B) through the leg/arm assembly (H) and
the back assembly(I).
Step 8:
On the back side of the bolt placed in step 6 (B), place a
washer (D) and then thread a nut (E) onto the bolt. Tighten with a
7/16 socket and wrench.
Step 9:
Repeat steps 1-7 for other leg/arm assembly (H) of chair.
Step 10:
Place the glider in the orientation shown in the user manual,
with the glide assembly (L) underneath.
Step 11:
Remove the 3 washers, bolt and nut which is assembled through
the bracket on the wrench.
Step 12:
Repeat step 11 with the rear bracket on the glide assembly
(L).
Step 13:
Repeat steps 11 & 12 for both sides of the glider, the glide
assembly should be attached at 4 corners with the brackets, and the
glider should swing freely.
Step 14:
Align the predrilled holes with the rear brace(M) and screw two
of the 2 inch(G) screws through the holes and into the brace.
Step 15:
Repeat step 14 on both sides of the brace to securely fixture it
into place between the two arm/leg(H) assemblies.
Step 16:
Attach the front brace (M) in the same manner as the rear using
the predrilled holes and included hardware.
Step 17:
Align the rear cover strip (K) with the predrilled holes on the
back and seat assemblies (I & J).
Step 18:
Reattach the rear cover strip removed in Step 1, (K) to the back
and seat assemblies (I & J) using the provided 1.25 inch (F)
and 1 inch screws (N). The screws are a #2 Square bit.
Blue Ridge Bent Back Glider
Instruction Manual
P/N: FF-BRSG
Buck Stove, New Buck Corp |200 Ethan Allen Dr, Spruce Pine, North Carolina 28777, United States | (828) 765-6144 | www.buckstove.com
Included Hardware
A B C DE F
2.5in Bolt 4PCS
G
3in Bolt 2PCS
N
3.5in Bolt 4PCS
Washer 18PCS
Nut 10PCS
1.25in Screw
2 in Screw 8PCS
1 in Screw
*Hardware without piece count comes preinstalled
Included Parts
H
I
J
Arm/Leg Assembly
K
Back Assembly
L
Seat Assembly
M
Rear Cover Strip
Glide Assembly
Front/Rear Brace
Required Tools
7/16 Socket Wrench
1/2 Socket
7/16 Wrench
1/2 Wrench
#2 Square Bit
Assembly Instructions
Step 1
Unscrew the loosely attached 1.25 in(F) & 1 in(N) screws, and remove the rear cover strip (K) and place aside for
final assembly.
Step 2
Begin the assembly process by placing the glider in the orientation shown to the right, with the back (I) and seat assembly (J) on their side.
Step 3
Align the holes on the arm assembly (H) with the holes going through the back (I)
and seat assemblies(J).
Step 4
Insert the 3.5 inch bolt (C) through a washer (D) and into the leg/arm (H), back (I) and seat (J) assemblies.
Step 5
Insert the 2.5 inch bolt (A) through a washer (D) and into the leg/arm (H) and seat
(J) assemblies.
Step 6
On the back side of the bolts (A & C) that were inserted through the seat (J), place a
washer and then thread a nut onto all of the bolts placed in steps 3-4. Tighten with 7/16
socket and wrench.
Step 7
Place the 3 inch bolt (B) through the leg/arm assembly (H) and the back assembly(I).
Step 8
On the back side of the bolt placed in step 6 (B), place a washer (D) and then thread a nut (E) onto the bolt. Tighten
with a 7/16 socket and wrench.
Step 9
Repeat steps 1-7 for other leg/arm assembly (H) of chair.
Step 10
Place the glider in the orientation shown to the right,
with the glide assembly (L) underneath.
Step 11
Remove the 3 washers, bolt and nut which is assembled through the bracket on the
glide assembly (L). Then place the bolt through the composite with a washer on either side. Slide it though the bracket and place a washer and thread the nut onto the end of the bolt. Tighten til snug with ½ in socket and
wrench.
Step 12
Repeat step 11 with the rear bracket on the glide assembly (L).
Step 13
Repeat steps 11 & 12 for both sides of the glider, the glide assembly should be attched at 4 corners with the
brackets, and the glider should swing freely.
Step 14
Align the predrilled holes with the rear brace(M) and screw two of the 2 inch(G) screws through the holes and into
the brace.
Step 15
Repeat step 14 on both sides of the brace to securely fixture it into place between the two arm/leg(H) assemblies.
Step 16
Attach the front brace (M) in the same manner as the rear using the predrilled holes and
included hardware.
Step 17
Align the rear cover strip (K) with the predrilled holes on the back and seat assemblies
(I & J).
Step 18
Reattach the rear cover strip removed in Step 1, (K) to the back and seat assemblies (I & J) using the provided 1.25
inch (F) and 1 inch screws (N). The screws are a #2
Square bit.
Buck Stove – Your locks, our security.
