3174 Network Camera
Product Information
The Network Camera is a surveillance camera that can be used for
indoor or outdoor installation. It comes with a mounting base,
dome, enclosure, and various connectors for network and power
supply. The camera supports Power over Ethernet (PoE) for
convenient installation.
Key Features:
- Network connector for network connection
- Power connector for power supply
- Mounting base for camera installation
- Micro SD card slot for optional storage
- Reset button for optional camera reset
- Security cap for outdoor installation (recommended)
Product Usage Instructions
1. Connecting Network Cable
- Loosen the nut from the main element.
- Run the network cable (without RJ45 connector) through both
elements. - Crimp the cable with an RJ45 connector.
- Connect the cable to the hermetic connector.
- Tighten the nut and the main cover.
2. Installation
- Ensure that the wall or ceiling is strong enough to withstand 3
times the weight of the camera. - Loosen the fixed screw to disassemble the camera.
- If your camera has a micro SD card slot, remove the cover from
the dome and insert the SD card. Install the cover back to the dome
and fix it firmly with screws. - Attach the drill template to the desired location on the wall
and drill the screw holes and cable hole according to the
template. - Route and connect the cables.
- Secure the mounting base to the ceiling or wall using the
provided screws. - Install the dome and enclosure to the mounting base.
- Adjust the dome to obtain an optimum view angle.
- Fix the camera with the fixed screw.
3. Network Connection
In a local area network (LAN), there are two ways to access the
camera:
- Access Through IP-Tool:
- Make sure the camera and PC are connected to the local
network. - Install IP-Tool from the provided CD and run it.
- Click on “Device Network Search” to find the camera’s IP
address and other network information. - To modify network parameters, enter the administrator password
and make necessary changes. - Modify the IP address and gateway of the camera to match the
local network segment of the computer.
- Open a web browser on a computer connected to the same local
network as the camera. - Enter the camera’s IP address in the browser’s address bar and
press Enter. - Login with appropriate credentials if prompted.
- Access and configure camera settings through the web-based
interface.
Network Camera
Quick Start Guide
Camera
Quick start guide
Tapping screw × 3
* 2 If the PoE switch is used to power the camera that supports PoE power supply, DC12V power supply is not required.
Connecting Network Cable
Please read this instruction carefully before operating the
CD
Drill template
Plastic plug ×3
unit and keep it for further reference.
All the examples and pictures used here are for reference only.
The contents of this manual are subject to change without notice.
Screwdriver
1
2
3
1 Warning and Caution
If the product does not work properly, please contact your dealer or the nearest service center. Never attempt to disassemble the camera yourself. (We shall not be responsible for any problems caused by unauthorized repair or maintenance.) Do not allow water or liquid intrusion into the camera. In the use of the product, you must be strict compliance with the electrical safety regulations of the nation and region. When the product is mounted on wall or ceiling, the device shall be firmly fixed. Do not use camera beyond specified voltage range. Do not drop the camera or subject it to physical shock. Avoid touching the camera lens. If cleaning is necessary, please use clean cloth to wipe it gently. Do not aim the camera at the sun or extra bright place. Do not place the camera in extremely hot, cold (the operating temperature shall be -30°C~60°C), dusty or damp locations, and do not expose it to high electromagnetic radiation. To avoid heat accumulation, good ventilation is required for operating environment.
3 Overview
1
2
5
3
4
6
1
Network connector
2
Power connector
3
Mounting base
4
Fixed screw
5
Micro SD card slot*
6
Reset*
Note: Micro SD card slot and reset are optional. If no such interfaces, please skip the above-mentioned(5, 6) instructions.
Security Cap
DC12V
Loosen the nut from the main element. Run the network cable (without RJ 45 connector) through the both elements. Then crimp the cable with RJ 45 connector. Connect the cable to the hermetic connector. Then tighten the nut and the main cover.
4 Installation
Please make sure that the wall or ceiling is strong enough to withstand 3 times the weight of the camera. Loosen the fixed screw to disassemble the camera. Remove the cover from the dome to insert the SD card. Then, install the cover back to the dome and fix it firmly with the screws. Note that the cover should not be installed unevenly. (Please skip this step if your camera has no micro SD card slot).
Fixed Screw Mounting Base
Enclosure
Cover
Dome
2 Package
* 1 It is recommended to install the security cap for outdoor installation.
Attach the drill template to the place where you want to fix the camera and then drill the screw holes and the cable hole on the wall according to the drill template.
44.2
(mm) Ø91.6
38.2
Ø51.0 Ø4.5
Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.
Install the dome and enclosure to the mounting base and then adjust the dome to obtain an optimum view angle. Finally, fix the camera with the fixed screw.
5 Network Connection
In LAN, there are two ways to access the camera. 1. Access Through IP-Tool; 2. Direct Access Through WEB Browser
Access Through IP-Tool
Switch
IPC
Network Cable
Router
Network Cable
MENU
Computer
Make sure that the camera and the PC are connected to the local network. Install IP-Tool from the CD and run it after installation.
Device Network Search
Immediate Refresh
Device Name Device Type Product Model IP Address Http Port
name name
IPC
unknown 192.168.226.201
80
IPC
unknown 192.168.1.2
80
name
IPC
unknown 192.168.1.3
80
About
Data Port Subnet Modify Network Parameter
9008 9008 9008
255.255. Mac Address CE :98 :23 :75 :35 :22 255.255. IP Address 192 .168 . 226 . 201
255.255. Subnet Mask 255 . 255 . 255 . 0
Gateway
192 .168 . 226 . 1
Modify i Tip: Enter the administrator password, and
then modify the network parameters.
Restore IPC Default Configuration
Total Device: 3
Local IP Address:192.168.1.4 Subnet Mask:255.255.255.0 Gateway: 192.168.1.1 DNS210.21.196.6
Modify the IP address. The default IP address of this camera is 192.168.226.201. Click the information of the camera listed in the above table to show the network information on the right hand. Modify the IP address and gateway of the camera and make sure its network address is in the same local network segment as the computer’s. Please modify the IP address of your device according to the practical situation.
Modify Network Parameter
Mac Address CE :98 :23 :75 :35 :22
IP Address 192 .168 . 1 . 201
Subnet Mask 255 . 255 . 255 . 0
Gateway
192 .168 . 1 . 1
Modify
For example, the IP address of your computer is 192.168.1.4. So the IP address of the camera shall be changed to 192.168.1.X. After modification, please enter the password of the administrator and click “Modify” button to modify the setting.
The default password of the administrator is “123456”. Double-click the IP address and then the system will pop up the web browser to connect IP-CAM. Follow directions to download and run the plugin in the computer. Then enter the user name and password in the login interface.
The default username is admin; the default password is 123456. Direct Access Through WEB Browser
IPC
Network Cable
MENU
Computer
The default network settings are as shown below: IP address: 192.168.226.201 HTTP:80 Subnet Mask: 255.255.255.0 Data Port:9008 Gateway: 192.168.226.1 You may use the above default settings when you log in the camera for the first time. Set the IP address of the PC and make sure the network segment should be as the same as the default settings of IP-CAM. Open the network and share center. Click “Local Area Connection” to pop up the following window. Select “Properties” and then select Internet protocol according to the actual situation (for example: IPv4). Next, click “Properties” button to set the network of the PC.
Open a browser and enter the default address of IP-CAM and confirm. Download and run the plugin in the computer. Enter the default username and password in the login interface to log in.
450043001057 A2
