CD 5014 Brindille Large Four Light Chandelier
Product Information: Brindille Large Four Light Chandelier
Item Number: CD 5014
This Brindille Large Four Light Chandelier is a stylish and
elegant lighting fixture that will enhance the ambiance of any
room. It is designed to be installed in accordance with local
installation codes and should be done by a person familiar with its
construction and operation.
Before installation, carefully inspect the item and its
contents. If any damage or defect is found, do not install and
contact customer support. Retain all packaging material until
installation is complete and approved.
Tools Required (Not Included):
- Phillips Screwdriver
- Slotted Screwdriver
- Wire Cutters
- Wire Strippers
Product Usage Instructions:
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Remove the mounting plate (B) from the canopy (H) by removing
the collar ring (I). - Install the mounting plate (B) to the junction box and secure
it with the provided mounting screws (C). - Feed the electrical wires through the bottom rod (K) and
connect them to the fixture (L). Repeat this step for the middle
rod (J), connecting it to the bottom rod (K). - Continue feeding the wires through the collar ring (I), canopy
(H), and top rod (G). - Holding the fixture upright, slide the collar ring (I) and
canopy (H) down and align them with the mounting plate (B). Secure
them together using the collar ring (I). - Connect the driver input hot wire (black) to the supply hot
wire (usually black) using the provided wire nut (A).
Caution: Do not reverse the hot and neutral
connections. - Connect the fixture neutral wire (black) to the driver output
wire (black) using the wire nut (A). - Connect the fixture hot wire (red) to the driver output wire
(red) using the wire nut (A). Caution: Do not
reverse the hot and neutral connections. - Ensure all wire connections are tight, then carefully tuck them
into the junction box. - Insert the driver into the mounting plate (B) bracket.
- Install the canopy (H) to the mounting plate (B) and secure it
with the collar ring (I). - Thread the glass shades (N) to the light sources (M).
Note: Do not over-tighten to avoid damaging the
shades. - Adjust the light sources (M) to the desired angle. They can be
rotated left or right and directed upwards or downwards.
Care Instructions:
Clean the chandelier only with a soft dry cloth or feather
duster. Do not use abrasive or chemical agents that may damage the
surface.
ASSEMBLY INSTRUCTIONS
D E
A
B
Diagram 1
D
C
E
A
F
G
H
I
J
K L
M N
Brindille Large Four Light Chandelier
Item # CD 5014
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Wire Cutters
Wire Strippers
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (B) from canopy (H) by removing collar
ring (I). 3. Install mounting plate (B) to the junction box and secure with
mounting screws (C). 4. Feed electrical wires through bottom rod (K) and connect to fixture (L).
Repeat for middle rod (J), connecting to bottom rod (K). 5. Continue feeding wires through collar ring (I), canopy (H) and top
rod (G). 6. Holding fixture upright, slide collar ring (I) and canopy (H) down and
rest on fixture (L). Then connect top rod (G) to middle rod (J). NOTE: Slide components down slowly to avoid damages. 7. Hang fixture swivel ball (F) to center of mounting plate (B) and secure with set screw (D) using provided wrench (E). 8. Cut excess wire, being sure to leave enough to reach the junction box. Separate wires
and strip insulation on each 5/8″. 9. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 1). Tighten. NOTE: It is imperative that the fixture is grounded. 10. Connect driver input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
D E
A
B
Diagram 1
D
C
E
A
F
G
H
I
J
K L
M N
Brindille Large Four Light Chandelier
Item # CD 5014
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
11. Connect driver input hot wire (black) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
12. Connect fixture neutral wire (black) to driver output wire (black) using wire nut (A).
13. Connect fixture hot wire (red) to driver output wire (red) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
14. Make sure all wire connections are tight, then carefully tuck into the junction box.
15. Insert driver into mounting plate (B) bracket. 16. Install canopy (H) to mounting plate (B) and secure with collar ring (I). 17. Thread glass shades (N) to light sources (M).
NOTE: Do not over-tighten otherwise shade could become damaged. 18. Adjust light sources (M) to desired angle.
NOTE: The light source can be rotated left or right and directed upwards or downwards.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
M
LI ST ED
US
