ICUSB-1 Single USB Charger
Product Information: ICUSB-1 / ICUSB-3 Single USB Charger
The ICUSB-1 / ICUSB-3 charger is designed to charge smartphones,
MP3 players, and other electronic devices. It is important to
ensure that the charger complies with the charging parameters of
the device before connecting it.
| Specification | ICUSB-1 / ICUSB-3 |
|---|---|
| Number of USB ports (type A) | 1 |
| Nominal input voltage | 110-240 V~ |
| Nominal input current | 0.25 A |
| Nominal output voltage | 5 V DC |
| Nominal output current | 1 A / 2 A |
| Ingress protection degree | IP 20 |
Warranty Conditions
A warranty period of 12 months is provided from the date of
purchase. In case of any defects, the defective ICUSB-1 / ICUSB-3
charger along with the proof of purchase should be sent to the
manufacturer or seller. The warranty does not cover mechanical
damages, defects resulting from unauthorized repairs, or improper
use of the product. The warranty period will be extended for the
duration of the repair.
Assembly Instructions
IMPORTANT: The installation must be carried out by a qualified
person with the power supply disconnected and in compliance with
national safety standards.
Refer to Figure 2 for the correct connection to
the installation. Improper connection may damage the charger or
cause it to work incorrectly. The USB charger mechanism consumes
idle power supply of approximately 0.2W.
Ensure that the charger is installed correctly and safely
according to the provided instructions.
USER MANUAL: ICUSB-1 / ICUSB-3 SINGLE USB CHARGER
Specification of ICUSB-1 / ICUSB-3 single USB charger The ICUSB-1 / ICUSB-3 charger is intended to charge devices like smartphones, MP3 players and other electronic equipment. Before connecting the device, check compliance of the charger with charging parameters of the given device.
54,00
54,00
Specification
Number of USB ports (type A)) Nominal input voltage Nominal input current Nominal output voltage Nominal output current Ingress protection degree
41,00
1 110-240 V~ 50/60Hz 0,25 A 5 V DC 1 A / 2 A IP 20
Warranty conditions Warranty is granted for a period of 12 months of the date of purchase. The defective ICUSB-1 /ICUSB-3 charger along with the proof of purchase should be sent to the manufacturer or to the seller. Warranty does not include mechanical damages, defects resulting from unauthorised repairs and improper use of the product. Warranty period will be extended for the duration of the repair.
1 I 2
ASSEMBLY INSTRUCTIONS
1. Remove the glass panel (1) with the label applying a knife or a flat screwdriver in the recess (3). 2. Remove the screw (2). 3. Dismantle the USB charger module (4). 4. Remove the spacer frame (5) from the assembly block (7). Pull away the block tabs or pull the frame tightly to do this. 5. Set the assembly block in the box (9) with tabs or screws at the box (8). 6. Insert the spacer frame in the external frame (6) and snap the entire set on the tabs protruding from the assembly block. 7. Connect the wires of the installation to the USB charger module as shown in Figure 2. 8. Insert the USB charger module in the intermediary unit. 9. Screw down the intermediary unit to the assembly block. 10. Attach the label and glass pane.
Fig. 1
Fig. 2 NOTE! The installation must be done by a person with sufficient qualifications, with power supply disconnected, and must comply with national safety standards. The connection to the installation should be done as shown in Figure 2. With improper connection, the charger may be damaged or may work incorrectly. USB charger mechanism with idle power supply consumes less than about 0,2W.
2 I 2
