Wingbo Wbcf-q028-ni 52 Inch Indoor Brushed Nickel Ceiling Fan Instruction Manual

WBCF-Q028-NI 52 Inch Indoor Brushed Nickel Ceiling Fan

Product Information:

The product is a ceiling fan with a blade bracket and a spare
part of a 12-inch downrod. It comes with a receiver, an outlet box,
and a remote control emitter that requires two batteries (12V 23A
and UM-44 AAARo3 DC 1.5Vx2). The fan has speed control buttons (HI,
MED, and LOW), an ON/OFF button for the lamp, a STOP button to turn
off the fan, and a fan timing button (1H, 2H, and 4H). It also has
an F/R button to control the direction of the fan (Forward and
Reverse).

Product Usage Instructions:

1. Attach the blade bracket to the fan motor assembly using two
   blade screws.
2. Attach the blade to the blade bracket using three blade screws
   and three washers.
3. Tighten all screws and washers securely. Repeat the same
   process for the other four blades.
4. Use the speed control buttons (HI, MED, and LOW) to adjust the
   fan speed.
5. Use the ON/OFF button to turn the lamp on or off.
6. Use the STOP button to turn off the ceiling fan.
7. Use the fan timing button (1H, 2H, and 4H) to set the timer for
   the fan.
8. Use the F/R button to control the direction of the fan (Forward
   and Reverse).
9. The remote control emitter requires two batteries (12V 23A and
   UM-44 AAARo3 DC 1.5Vx2).
10. To use the remote control emitter, install the transmitter wall
    mount holder with two screws.
11. The remote control emitter has a remote control distance of
    25-30 meters.

Blade bracket

Spare part-12- inch downrod

D.

MED

LOW

HI

STOP

2H

1H

4H

R/F

D

Outlet box
Black (hot)
Black (“AC IN L”)
Receiver
Black Red Orange
Orange Red Black

White (neutral) Green or bare copper (ground) White (“AC IN N”)
Bule(to light) White (neutral) Green(ground)
White (neutral) Bule (to light)

Attach the blade bracket to the fan motor assembly by using the two blade screws, Attach the blade to the blade bracket by using the three blade screws and three washers, Tighten all screws and washers securely. Repeat same process for the other four blades.

Screw Washer

Blade screw

Blade bracket

Blades

KINDLY REMINDERS: Learning code maching mode is used between emitter and receiver,Turn “ON” the supply power within 30 seconds and press the emitter’s “LIGHT” and “Hi”button for 3 seconds, it can load normally after hearing the “BEE” which means learning successfully and it can works normally.(PS:Learing mode is not acepted after turn “ON” the supply power for 30 seconds)

1. speed control button of fan: HI. MED AND LOW are speed button.
2. LI:ON/OFF the lamp.
3. STOP :Turn off the ceiling fan. 4. Fan timing button: 1H.2H and 4H. 5. F/R : Controls the direction of the fan
“Forward and Reverse”. 6. Battery for RF emitter: 12V 23A
Bettery foremitter:UM-44 AAARo3 DC 1.5Vx2. 7. RF emitter:Renote control distance at 25-30 meters.
emitter:Remote control distance within 10 meters.

MED

LOW

HI

STOP

2H

1H

4H

R/F

LIGHT ON/OFF
Installation of transmitter wall Mount holder with two screws.

RED ORANGE

TO FAN REVERSE L TO FAN REVERSE N

r l