Adjustable Multi-Pieces Solar Panel Mounting Brackets Kit System
Product Information
The product is a solar panel mounting bracket designed for
installation on roofs or other surfaces. It includes various
components and accessories for secure and efficient
installation.
- Model: U8(SE)U
- Tel: +1-4846260-973597-80202322
- E-mail: [email protected]
- Web: www.eco-worthy.com
Product Usage Instructions
Notice
Please wear gloves before installation to prevent hand
injuries.
To avoid a shock hazard, keep the panel covered with a dark
material during installation and avoid contact with the output
terminals.
If the panels will be mounted on a roof, make sure the material
is strong enough to provide support to the solar panel including
wind loading.
To minimize wind loading effects in an RV or mobile application,
place the panel’s longest edge parallel with the direction of wind
travel.
If you want to place the bracket on the ground, please choose a
flat, hard surface, use self-tapping screws for installation with
the plane, or choose a heavy thing to press the bracket.
Components & Accessories
| Image | Specification | Model | Quantity |
|---|---|---|---|
| 41mm bracket with perforation base | 41*41*1.2*200mm steel c-shape steel with perforation | 4 | |
| Triangle joint | 41*41*1.2*600mm steel c-shape steel with perforation | 4 | |
| Panel clamp +45mm | 41*41*1.2*1000mm c-shape steel with perforation | 6 |
Installation
Step 1: Set the four feet
Put the four base feet on the ground or surface where you want
to install the brackets.
Step 2: Mount the vertical rods
Note: The fixing position of the front foot should be at the
second hole of the rod.
Step 3: Connect horizontal rods
Use the 4 inside connectors and 6 rest 1000mm C-shape steel rods
to connect the horizontal rods.
Step 4: Tighten all screws
Make sure all screws are tightened before putting on the panels.
You can check it with a wrench.
Step 5: Mount panels and clamps
Put the panels on the two horizontal rods, mount the clamps into
the rods’ rail, and use the Y-shape sleeve to tie the screws on the
clamp, so it’ll press the panels on the rods. Use the two-head
clamp between two panels and the side clamp to hold one panel’s
side.
Tel+1-4846260-973597-80202322(U8(SE)U) E-mail:[email protected] Web:www.eco-worthy.com
Notice
Please wear gloves before installation to prevent hand injuries
To avoid a shock hazard, keep the panel covered with a dark material during installation and avoid contact with the output terminals.
If the panels will be mounted on a roof, make sure the material is strong enough to provide support to the solar panel including wind loading.
To minimize wind loading effects in an RV or mobile application, place the panel’s longest edge parallel with the direction of wind travel.
If you want to place the bracket on the ground, please choose a flat, hard surface, use self-tapping screws for installation with the plane, or choose a heavy thing to press the bracket.
Components&Accessories
(Some components already pre-installed)
Image Specification
Model Quantity
41mm bracket with perforation
base
4
Triangle joint
joint
4
panel clamp +45mm
35mm
M8 screw + 6mm M8
two-head panel
6
nut
clamp
-1-
panel clamp + 25mm
35mm
M8 screw + 6mm M8 side panel
4
nut
clamp
20mm M8 hexagonal
screw + M8 flange nut short bolt
24
+ 2*pads
60mm M10 hexagonal screw + M10 flange nut
long bolt
12
20mm M8 hexagonal
screw + 6mm M8
inside bolt
4
flange nut + 1*pad
41*41*1.2*200mm steel c-shape steel with perforation
2
41*41*1.2*600mm steel c-shape steel with perforation
2
41*41*1.2*1000mm
c-shape steel 6
steel with perforation
41*21*1.2*1000mm steel with perforation
c-shape steel
2
41*21mm cap
top cap
8
80mm M10 expanding expanding
screw
screw
8
40*20*1.4mm connector
inside connector
4
-2-
Installation
Step.1 Set the four feet
Put those four base feet on the ground or surface where you want to install the brackets.
Step.2 Mount the vertical rods
Use screws to fix the two vertical rods on the feet, and it’s able to set the angel degree as 30, 35, 40, 45 by diverse the back foot holes, the order be, top hole-30, second-35, third-40, fourth-45. You could choose the proper angle according to your location and latitude, E.g. If you live in California, set the vertical rods at 35°hole. So that the panels can get the maximum solar irradiance.
Note: The fixing position of the front foot should be at the second hole of the rod.
45°
30°
-3-
Step.3 Connect horizontal rods
There are 4*inside connectors, and 6 rest 1000mm C-shape steel rods.
·First, hook up 4 rods on the vertical rods with the 20mm M8 hexagonal screw, put each one C-shape rod on each connecting point of vertical rods.
·Then, use the inside connectors to fix the inside side of those installed horizontal rods, use 2 of 20mm M8 hexagonal screw for each rod’s installation.
·In the end, put the rest 2 rods on in the middle, so the both sides will be connecting with the inside connectors.
1
2
3
4
-4-
·Use top cap to install on sides of rods to prevent scratches
Step.4 Drill the feet into the surface When all rods get mounted, place the position on ground or flat surface that needs to be fixed and make a hole mark for the base feet fixing. In case of heavy wind or storm, If there is no solid surface, you can place a cement block for the drilling, or just put some heavy stuff to cover the feet. Remember to put the brackets towards the south side, it’s the best direction to absorb the sunlight in the north hemisphere. Then use an impact drill to drill a hole with a diameter of 12mm and a depth of 55mm in the marked position. After drilling the hole, use the M10x80 expansion screw to fix the feet firmly.
-5-
Make sure all screws tied before put on the panels, you can check it with the wrench. Step.5 Mount panels and clamps Put the panels on the two horizontal rods, mount the clamps into the rods’ rail, and use the Y-shape sleeve to tie the screws on the clamp, so it’ll press the panels on the rods. Two-head clamp be put in between two panels, and side clamp to hold one panel’s side.
-6-
Sell Diamonds, Jewelry and Watches for the Best Price | Worthy
ECO-WORTHY: Solar Panel Kits & Lithium Battery &DIY Solar Power System
