Towing Master 10201104p Electric Marine Swivel Jack Instructions

10201104P Electric Marine Swivel Jack

Product Information: ELECTRIC MARINE SWIVEL JACK With Touch
Panel & 7-Way Connector

The Electric Marine Swivel Jack is a product designed to attach
to the side of straight trailer tongue of a boat, power sport or
equipment trailer. The swivel trailer jack allows the user to move
level and hitch the trailer with ease. It has a capacity of 1500
lbs and is equipped with a new one-piece Industrial design cover
increasing waterproof coverage. Improved LEDs lights illuminate the
area in front of the jack for superior nighttime visibility. The
7-way connector plugs into your vehicle connector to let you lift
or lower the jack with the push of a button, no hard wiring
required. The jack is made of aluminum and comes with an
omni-directional wheel and swivel mounting plate.

Technical Specifications

Tools and Components Required

• Two Plates (included)
• Four M10 Lock nut (included)
• Four M10 x 100 Hex bolts (included)
• 9/16in. Wrench (owner supplied, not included)
• Torque Wrench (owner supplied, not included)
• Wire Cutters (owner supplied, not included)
• Wire Strippers (owner supplied, not included)
• Crimpers or Soldering Iron (owner supplied, not included)

General Safety Rules

• Read and understand all instructions. Failure to follow all
  instructions listed below may result in serious injury.
• The warnings, cautions, and instructions discussed in this
  instruction manual cannot cover all possible conditions or
  situations that could occur. It must be understood by the operator
  that common sense and caution are factors which cannot be built
  into this product, but must be supplied by the operator.
• Do not allow persons to operate or assemble this electric jack
  until they have read this manual and have developed a thorough
  understanding of how the electric jack works.

Jack Use and Care

• Do not modify the jack in any way. Unauthorized modification
  may impair the function and/or safety and could affect the life of
  the equipment. There are specific applications for which the jack
  was designed.
• Always check for damaged or worn-out parts before using the
  jack. Broken parts will affect the jack operation. Replace or
  repair damaged or worn parts immediately.
• Store idle jack. When jack is not in use, store it in a secure
  place out of the reach of children. Inspect it for good working
  condition prior to storage and before re-use.
• Disconnect the battery from the trailer jack if it does not
  require power for several days. This will prevent the battery from
  discharging.

Product Usage Instructions

• Before operating the Electric Marine Swivel Jack, read all
  assembly and operation instructions carefully to avoid personal
  injury.
• Attach the jack to the side of straight trailer tongue of a
  boat, power sport or equipment trailer using the provided plates,
  lock nuts, and hex bolts.
• Check for damaged or worn-out parts before using the jack.
  Replace or repair damaged or worn parts immediately.
• Connect the 7-way connector to your vehicle connector to let
  you lift or lower the jack with the push of a button, no hard
  wiring required.
• To swivel the jack to a horizontal position during
  transportation, use the manual crank handle.
• Store the idle jack in a secure place out of reach of children.
  Inspect it for good working condition prior to storage and before
  re-use.
• If the trailer jack does not require power for several days,
  disconnect the battery to prevent it from discharging.

ELECTRIC MARINE SWIVEL JACK With Touch Panel & 7-Way Connector
1500 lbs. Capacity
WARNING
Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions
may result in serious personal injury.
SAVE THESE INSTRUCTIONS
Item# 10201104P

INTENDED USE
This Electric Marine Swivel Jack attaches to the side of straight trailer tongue of a boat, power sport or equipment trailer. The swivel trailer jack allows the user to move level and hitch the trailer with ease. It swivels to a horizontal position during transportation.
The 7-way connector plugs into your vehicle connector to let you lift or lower the jack with the push of a button, no hard wiring required.
Your jack is equipped with a new one-piece Industrial design cover increasing waterproof coverage. Improved LEDs lights illuminate area in front of jack for superior nighttime visibility.

TECHNICAL SPECIFICATIONS

Property Item Number Type Loading Capacity (lbs.) Support Capacity (lbs.) Clearance: Bracket to Jack Top (in.) Length of Travel (in.) Length Retracted (in.) Length Extended (in.) Jack Tube Size (in.) Crank Type Ground Support Mount Type Construction

Specification 10201104P 12V DC 1,500 2,250 16.8 14 14.2 (Measured from ground to center of mounting point) 28.2 (Measured from ground to center of mounting point) 2.2 Includes manual crank handle Omni-directional wheel Swivel mounting plate Aluminum

Tools and Components Required Two Plates (included) Four M10 Lock nut (included) Four M10 x 100 Hex bolts (included) 9/16in. Wrench (owner supplied, not included) Torque Wrench (owner supplied, not included) Wire Cutters (owner supplied, not included) Wire Strippers (owner supplied, not included) Crimpers or Soldering Iron (owner supplied, not included)

Page2 of 8

GENERAL SAFETY RULES
WARNING
Read and understand all instructions. Failure to follow all instructions listed below may result in serious injury.
The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions or situations that could occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
CAUTION
Do not allow persons to operate or assemble this electric jack until they have read this manual and have developed a thorough understanding of how the electric jack works.
JACK USE AND CARE
Do not modify the jack in any way. Unauthorized modification may impair the function and/or
safety and could affect the life of the equipment. There are specific applications for which the jack was designed.
Always check for damaged or worn-out parts before using the jack. Broken parts will affect
the jack operation. Replace or repair damaged or worn parts immediately.
Store idle jack. When jack is not in use, store it in a secure place out of the reach of children.
Inspect it for good working condition prior to storage and before re-use.
Disconnect the battery from the trailer jack if it does not require power for several days.
This will prevent the battery from discharging.
Do not force the trailer jack. Do not attempt to lift more than the maximum lifting capacity of
1500 pounds.
This electric trailer jack has been designed to attach to the side of a straight tongue trailer. Never attempt to adjust the universal wheel (#25) when there is any load on the jack. Make
certain the universal wheel and inner tube are securely connected before using the jack.
Page3 of 8

INSTALLATION INSTRUCTIONS

Before installation, compare the lift capacity of the electrical jack with your trailer to ensure safe operation of the jack.

1. Park the trailer on a level surface, block the tires of the trailer and support trailer tongue. 2. This marine electric trailer jack has been designed to attach to the side of a straight tongue trailer. 3. Do not connect this marine jack to the trailer battery before install the jack. 4. Place the trailer jack against the tongue and position the mounting bracket (#19) on the opposite side
of the tongue. 5. Align the holes in the mounting bracket (#19) with holes in the plate (#23). 6. Insert the 4 bolts (#21) through the mounting bracket (#19) and plate (#23). Push bolts through the top
and bottom bolt holes on the right side. 7. Slide a mounting plate over both bolt ends on the right side. Secure with locknuts, torque to 25 ft. lbs. 8. Repeat with a mounting plate on the left side. 9. Adjust the jack’s position if necessary. The mounting bracket should be square with the trailer tongue. 10. Tighten each nut evenly to secure the trailer jack in place. 11. Connect the jack to the vehicle. Wire lead from the jack directly to the positive (+) terminal of the
battery. This unit has a built-in circuit breaker which automatically trips and resets. Reconnect the battery ground cable. This jack includes a 7-way connector. Insert the 7-way connector into the 7-way receiver on the towing vehicle. 12. Check for proper installation, by pressing the motor switch UP for extending the jack and DOWN for retracting the jack. Also check that the light switch turns on the LED light.

Tip: The trailer connector on the vehicle must match the trailer connector on the jack to power it.
Test that the correct terminal is receiving power with a test light. Number 4 on the connector will receive power. Connector number 1 is the neutral ground. Consult a qualified technician on replacing the connector if there is a mismatch between the vehicle and jack connectors.
OPERATION
1. Park the trailer on a level surface and block the wheels. Tip: For nighttime hookups, turn the light switch ON to illuminate your work area.
2. Twist the swivel trailer jack until it is vertical. Pull the pull rod (#26) and insert to mounting bracket (#19) and lock the swivel trailer jack into position

WARNING
Do not stack blocks under the jack’s foot to increase the height. Stacked blocks may become unstable and fall.
3. Extend the jack by pushing the operating UP switch. Note: Under heavy use, the internal circuit breaker may open and cause the motor to switch off. In this case, release the operating switch and wait 15 seconds for the breaker to reset before resuming operation.
Page4 of 8

4. Retract the jack by pushing the operating DOWN switch. Note: The jack will stop automatically at the end of the extension or retraction stroke. If you attempt to extend or retract the jack and it does not respond, it may be at the end of the stroke. If the jack fails to respond, try operating it in the opposite direction. If it will not operate in either direction, refer to the troubleshooting guide.
5. When the jack is not in use, adjust the jack to a horizontal state in order to prevent the jack from touching the ground when the trailer is moving. Pull out the pull rod (#26) to swivel and lock the jack into a horizontal position.
6. When in use, the jack must be in a vertical state. Pull out the pull rod (#26) to swivel and lock the jack into a vertical position.
7. Tip: When pressing the UP or DOWN button, the jack will automatically detect voltage. If the voltage is lower than 10V, the jack will sound an alarm. When jack reaches the highest or lowest position, the jack will sound an alarm. The jack will need to reset for 10 seconds. After this period, the jack can either be lowered (if it was at its highest position) or raised (if it was at its lowest position). Example 1: If the jack is at the maximum height and you press the up button, the jack will not move. It will sound an alarm and the power will shut off for 10 seconds. If you press the down button, the jack will be able to retract normally. Example 2: If the jack is at the minimum height and you press the down button, the jack will not move. It will sound an alarm and the power will shut off for 10 seconds. If you press the up button, the jack will be able to extend normally. If the jack is connected to the vehicle, but has not been operated for at least two minutes, the jack will automatically power off. Pressing the UP or DOWN button will awaken the jack.
Page5 of 8

Troubleshooting

Refer to below troubleshooting guide if the device does not function properly. If unable to do so, have a qualified technician service the device.

Failure

Possible Cause

No or low voltage

Motor will not

operate

Open Internal Circuit Breaker

Open Manual Reset Circuit Breaker

Light work

doesn’t Loose wires on the ON/OFF switch Bad light bulb

Corrective Action Check trailer battery and electrical connections. Must have minimum of 10V DC to operate.
Wait 15 seconds for breaker to close
Reset the breaker by pressing the button on the breaker.
Secure wire connection
Replace bulb.

Page6 of 8

ENLARGED ELECTRIC JACK PARTS VIEW
Page7 of 8

PARTS LIST

Part Number

Part Description

Qty.

1

Override Protection Cover

1

2

Switch Cover

1

3

Plastic Cover (right)

1

4

Plastic Cover (left)

1

5-10

Gear Motor Box Assembly

1

11

Drive Shaft

1

12

PCB Board Assembly

1

13

LED Light

1

14

7-Way Connector

1

15

ACME Screw

1

16

Outer Tube

1

17

Crank Handle

1

18

Wheel Mounting Plate

1

19

Mounting Bracket

1

20

Inner Tube

1

21

M10 x 100 Hex bolts

4

22

M10 Lock nut

4

23

Plate

2

24

M10*25 Outer hexagon bolt M10 lock nut

4

25

Universal Wheel

1

26

Pull Rod

1

Limited 1-Year Warranty
We make every effort to assure that this product meets high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one years from the date of manufacture, provided that installation and use of the product is in accordance with product instructions. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
Save this manual for reference. Call or email our customer service department for troubleshooting help or replacement parts. Toll Free 1-800-545-9633

Page8 of 8