KW 5136 Covet Small Ring Pendant
Product Information
Product Name: Covet Small Ring Pendant
Item Number: KW 5136
Installation Type: Option 1: Canopy Mounted
Driver
Usage Type: Ceiling Mounted
Care Instructions: Clean only with a soft dry
cloth or feather duster. Do not use abrasive or chemical
agents.
Product Usage Instructions – Option 1: Canopy Mounted
Driver
- Carefully remove all parts from the box. Place on a clean, soft
surface. - Remove mounting plate (B) from driver housing (I) and canopy
(J) by removing collar ring (K). - Install mounting plate (B) to the junction box and secure with
mounting screws (G). - Feed electrical wires through bottom rod (N) and thread to the
junction box. - Connect supply ground wire (usually green or bare copper)
around the green grounding screw. Tighten. - Continue supply ground wire and connect to filter (E) ground
wire (green/yellow) using wire nut (A). Note: It is imperative that
the fixture is grounded. - Connect filter (E) input neutral wire (white) to the supply
neutral wire (usually white) using wire nut (A). - Connect filter (E) input hot wire (black) to the supply hot
wire (usually black) using wire nut (A). Caution: Do not reverse
the hot and neutral connections. - Connect fixture neutral wire (black) to driver (F) output wire
(black) using wire nut (A). - Connect fixture hot wire (red) to driver (F) output wire (red)
using wire nut (A). Caution: Do not reverse the hot and neutral
connections. - Make sure all wire connections are tight, then carefully tuck
into the junction box. - Insert filter (E) and driver (F) into the center of the tall
mounting plate (B). - Install driver housing (I) and canopy (J) to the tall mounting
plate (B) and secure with collar ring (K).
Product Usage Instructions – Option 2: Ceiling Mounted
Driver
- Carefully remove all parts from the box. Place on a clean, soft
surface. - Remove mounting plate (B) from driver housing (I) and canopy
(J) by removing collar ring (K). - Install mounting plate (B) to the junction box and secure with
mounting screws (G). - Feed electrical wires through bottom rod (N) and thread to the
junction box. - Connect supply ground wire (usually green or bare copper)
around the green grounding screw. Tighten. - Continue supply ground wire and connect to filter (E) ground
wire (green/yellow) using wire nut (A). Note: It is imperative that
the fixture is grounded. - Connect filter (E) input neutral wire (white) to the supply
neutral wire (usually white) using wire nut (A). - Connect filter (E) input hot wire (black) to the supply hot
wire (usually black) using wire nut (A). Caution: Do not reverse
the hot and neutral connections. - Connect fixture neutral wire (black) to driver (F) output wire
(black) using wire nut (A). - Connect fixture hot wire (red) to driver (F) output wire (red)
using wire nut (A). Caution: Do not reverse the hot and neutral
connections. - Make sure all wire connections are tight, then carefully tuck
into the junction box. - Insert filter (E) and driver (F) into the center of the tall
mounting plate (B). - Install driver housing (I) and canopy (J) to the tall mounting
plate (B) and secure with collar ring (K).
ASSEMBLY INSTRUCTIONS Option 1: Canopy Mounted Driver
C D
C D
Diagram 1
Diagram 2
A B E F A G H I J K L
M
N
O
Covet Small Ring Pendant
Item # KW 5136
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Wire Strippers
Slip-joint pliers
Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (B) from driver housing (I) and canopy (J)
by removing collar ring (K). 3. Install mounting plate (B) to the junction box and secure with
mounting screws (G). 4. Feed electrical wires through bottom rod (N) and thread to
connector (O). Repeat for middle rod (M), connecting to bottom rod (N). 5. Continue feeding wires through collar ring (K), canopy (J), driver housing (I) and top rod (L). 6. Holding fixture upright, slide collar ring (K), canopy (J) and driver housing (I) down bottom rods (N) and rest on connector (O). Then connect top rod (L) to middle rod (M). NOTE: Slide components down slowly to avoid damages. 7. Hang fixture swivel ball (H) to center of tall mounting plate (B) and secure with set screw (C) using provided screwdriver (D). See diagram 1. 8. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS Option 1: Canopy Mounted Driver
C D
C D
Diagram 1
Diagram 2
A B E F A G H I J K L
M
N
O
Covet Small Ring Pendant
Item # KW 5136
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
9. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten. Continue supply ground wire and connect to filter (E) ground wire (green/yellow) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
10. Connect filter (E) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
11. Connect filter (E) input hot wire (black) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
12. Connect fixture neutral wire (black) to driver (F) output wire (black) using wire nut (A).
13. Connect fixture hot wire (red) to driver (F) output wire (red) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
14. Make sure all wire connections are tight, then carefully tuck into the junction box.
15. Insert filter (E) and driver (F) into center of tall mounting plate (B). 16. Install driver housing (I) and canopy (J) to tall mounting plate (B) and
secure with collar ring (K).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS Option 2: Ceiling Mounted Driver
DC
C D
Diagram 1
Diagram 2
F
E A P H G J K
L
M
N
O
Covet Small Ring Pendant
Item # KW 5136
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Wire Strippers
Slip-joint pliers
Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface.
2. Place driver (F) into ceiling and route all wires through one of the
knockouts in the junction box. 3. Remove mounting plate (B) from driver housing (I) and canopy (J)
by removing collar ring (K). NOTE: Driver housing (I) will be not be used for ceiling mounted assembly. Keep part and store for future use. 4. Install mounting plate (P) to the junction box and secure with mounting screws (G). 5. Feed electrical wires through bottom rod (N) and thread to connector (O). Repeat for middle rod (M), connecting to bottom rod (N). 6. Continue feeding wires through collar ring (K), canopy (J), driver housing (I) and top rod (L). 7. Holding fixture upright, slide collar ring (K), canopy (J) and driver housing (I) down bottom rods (N) and rest on connector (O). Then connect top rod (L) to middle rod (M). NOTE: Slide components down slowly to avoid damages. 8. Hang fixture swivel ball (H) to center of short mounting plate (P) and secure with set screw (C) using provided screwdriver (D). See diagram 1.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS Option 2: Ceiling Mounted Driver
DC
C D
Diagram 1
Diagram 2
F
E A P H G J K
L
M
N
O
Covet Small Ring Pendant
Item # KW 5136
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
9. Cut excess wires, being sure to leave enough to reach the junction box. Separate wires, and strip insulation on each 5/8″.
10. Connect supply ground wire (usually green or bare copper) around the green grounding screw (see diagram 2). Tighten. Continue supply ground wire and connect to filter (E) ground wire (green/yellow) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
11. Connect filter (E) input neutral wire (white) to the supply neutral wire (usually white) using wire nut (A).
12. Connect filter (E) input hot wire (black) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
13. Connect fixture neutral wire (black) to driver (F) output wire (black) using wire nut (A).
14. Connect fixture hot wire (red) to driver (F) output wire (red) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
15. Make sure all wire connections are tight, then carefully tuck into the junction box.
16. Install canopy (J) to short mounting plate (P) and secure with collar ring (K).
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.
M
LI ST ED
US
