George Kovacs P1894-613-l Missing Link 24.875 Inch 1 Light Polished Nickel Led Vanity Light Instruction Manual

P1894-613-L Missing Link 24.875 Inch 1 Light Polished Nickel LED Vanity Light

Product Information

The product is a light fixture with the item number P1894-613-L.
The installation instructions are for a new fixture produced on
October 19, 2021. The fixture is compatible with ELV and/or LED
dimmer switches.

Product Usage Instructions

1. Before beginning installation, shut off power at the fuse box
   or circuit breaker box.
2. Remove the old fixture and its mounting hardware.
3. Unpack the new fixture and lay out all parts in a clear
   area.
4. Position the mounting plate on the wall and mark the location
   for two drywall anchors. Pre-drill the holes for drywall anchors
   and insert them into the wall.
5. Attach the mounting plate to the junction box using mounting
   screws. Ensure that the side of mounting plate marked GND faces
   out.
6. Connect the electrical wires as shown in Fig. 2, making sure
   all wire connectors are secured. If your junction box has a ground
   wire, connect the fixture’s ground wire to it. Otherwise, connect
   the fixture’s ground wire directly to the mounting plate using the
   green screw provided. After connecting wires, tuck them carefully
   inside the junction box.
7. Place back plate over mounting plate and secure with
   screws.
8. Align the glass shade onto back plate and secure with plastic
   washers and screws.
9. Place decorative frame over glass shade and secure with
   screws.

To replace the LED module:

1. Shut off power.
2. Remove decorative frame, plastic washers, and glass shade from
   back plate by loosening screws.
3. To remove fixture from the wall, loosen screws and back plate
   from mounting plate. Disconnect wire connectors and place back
   plate on a clean surface.
4. Press the button on printed L quick connector on LED module
   with a screwdriver to disconnect the black wire. Repeat by pressing
   the button on printed N quick connector on LED module to disconnect
   the white wire.
5. Remove screws and carefully remove LED module.
6. Reverse steps b-e for installing the new LED module.

INSTALLATION INSTRUCTIONS

Item#P1894-613-L (New. 2021/10/19)

READ AND SAVE THESE INSTRUCTIONS
W AR N I N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .

AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.

MOUNTING THE FIXTURE (Fig.1)
1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clear area. Take care not to misplace any small parts necessary for installation.
3. Loosening screws (C) to remove mounting plate (A) from back plate (D). Position mounting plate (A) on the wall and mark the location for two drywall anchors (F). Pre-drill the holes for drywall anchors (F). Insert drywall anchors (F) into the wall.
4. Attach the mounting plate (A) to the junction box (not included) using mounting screws (B). The side of mounting plate (A) marked “GND” must face out.
5. Screw wood screws (H) through the holes into drywall anchor (F) to secure mounting plate (A) as shown in Fig.1.

Fig. 1
Set#A-021-480119 -Mounting Screw*2 -Ground Screw -Mounting Plate

C

G

C K E

CONNECTING THE WIRES (Fig. 2)

F

6. Connect the electrical wires as shown in Fig. 2, making sure that all wire connectors are secured. If your junction box has a ground wire (green or bare copper), connect the fixture’s ground

A H

B

C D

wire to it. Otherwise, connect the fixture’s ground wire directly to

the mounting plate (A) using the green screw provided. After the

wires are connected, tuck them carefully inside the junction box.

FINISHING THE INSTALLATION (Fig.1)
7. Place back plate (D) over mounting plate (A) and secure with screws (C).
8. Align glass shade (E) onto back plate (D) and secure with plastic washers (K) and screws (C).
9. Place decorative frame (G) over glass shade (E) and secure with screws (C).
Replacing LED module (Fig.3)
The LED module can be replaced by a qualified electrician without cutting of wire and without damage to any decorative element to which the fixture is attached. See installation steps for more details (Fig 3.) a. Shut off the power. b. Loosening screws (C), remove decorative frame (G), plastic
washers (K) and glass shade (E) from back plate (D). c. To remove fixture from the wall, loosen screws (C) and back
plate (D) from mounting plate (A). Disconnect wire connectors and place back plate (D) on a clean surface. d. Press the button on printed “L” quick connector on LED module (I) with screwdriver (not included) to disconnected the black wire. Repeat by pressing the button on printed “N” quick connector on LED module (I) to disconnect the white wire. e. Remove screws (J) and then remove LED module (I) carefully. f. Reverse steps b-e for installing the new LED module.

Fig. 2
FIXTURE WIRES Black or Smooth
Fig. 3

Note: Illustration (Fig. 1) on this manual is for

A

installation purposes only. It may or may not be identical

to the fixture purchased.

Dimmable with ELV and/or LED compatible wall dimmer switches.

FIXTURE WIRES White or Ribbed HOUSE WIRES Black (Hot)

FIXTURE WIRES Green or Bare Copper (Ground)

HOUSE WIRES White (Neutral)

HOUSE WIRES Green (Ground)

C

G

C K E Screw driver
C D
I J

IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.

LA-3454E