The Home Depot Ws-094d 4-person 21 Jet Hot Tub With Pearl White Interior And Bluetooth User Manual

WS-094D 4-Person 21 Jet Hot Tub with Pearl White Interior and Bluetooth

Product Information

The WS-094D is a sanitary ware product designed for a
comfortable and relaxing bathing experience. It features a
dual-speed pump with a power output of 1.5KW/0.35KW and a heater
with a power output of 3000W. The product has a size of
2060x1760x790mm and operates on a voltage range of 220V-240V at
50Hz.

Product Usage Instructions

Step 1: Installation

Before using the product, it is important to install it
correctly. Follow the steps below:

1. Ensure that the product is connected to a power source within
   the voltage range of 220V-240V at 50Hz.
2. Connect the dual-speed pump and heater to the appropriate power
   outlets.

Step 2: Drainage

Proper drainage is essential for the functioning of the product.
Follow the steps below:

1. Ensure that the drain pipe is properly connected to the
   product.

Step 3: Cleaning and Maintenance

To keep the product in good condition, regular cleaning and
maintenance are required. Follow the guidelines below:

1. Use ordinary detergent and a soft cloth to clean the product.
   Avoid using detergents containing acetone or ammonia liquid.
2. If there are marks or glue on the surface of the bathtub,
   polish it with a soft cloth dipped in gas.
3. To remove scratches on the bathtub surface, use 1500# frosted
   paper dipped in liquid and burnish it with toothpaste.
4. If there is furring on the surface of the bathtub, remove it
   using a mild acid detergent such as lemon juice or heated
   vinegar.
5. Avoid wiping the chrome plated spare parts with chemical
   detergents. Clean them with a soft cloth.
6. Regularly check the water pipe for cracks or blockages.
7. If there are any obstructions in the jets, twist them out and
   remove the blockage.
8. To clean the hydro-massage equipment, fill the bathtub with hot
   water (40°C) and add 2g/L detergent. Run the hydro-massage function
   for more than 5 minutes, then drain the water. Repeat the process
   with cold water for 3 minutes and dry the bathtub with a
   towel.

Troubleshooting

If you encounter any issues with the product, refer to the
troubleshooting guide below:

Problem: No power or electricity leaking protection device is
activated

• Reasons:
  1. The electricity leaking protection device cuts off power when
     the electricity line is not well connected.
  2. There may be a phenomenon of electricity leaking in the power
     or electricity circuit.
• Maintenance:
  1. Check and reconnect the wiring system.
  2. Check the power source, electricity circuit, and ground
     line.

Problem: Water Jets are not working

• Reasons:
  1. Check if the system is turned on.
  2. The impeller of the water pump may not be rotating.
  3. The water pump may be broken due to working without water
     coming in.
• Maintenance:
  1. Turn on the system.
  2. Check and remove any garbage inside the pump. The switch pipe
     can be removed for this purpose.
  3. If necessary, install a new water pump.

Problem: The intensity of hydro-massage cannot be adjusted

• Reasons:
  1. The water pump’s suction may not have enough power.
  2. The air adjustment valve may be abnormal.
  3. The jets or nozzles may be blocked.
• Maintenance:
  1. Check if the water pump is working normally.
  2. Replace the air adjustment valve if necessary.
  3. Remove any obstructions in the jets.

WS-094D

Dear user, Thank you very much for purchasing our sanitary ware. To enable you to use this product safely and effectively, please read this installation and operation manual carefully before use.

Cautions
1.Please connect the water pipe before installed the products. (Fig.1) 2.Please ensure that the product installed reliable electric leakage protection device, the power plug contains earth line, and make sure it is reliable earthing. Check the protect system of leakage protection each time before use. 3.Before turn on water pump, check if the water level over jets 10 to 20 mm or not, make sure regular usage of water pump otherwise it will be destroy because of water leakage. 4.Do not turn on water pump, heat pump or air bubble pump without water.
5.People with Hypertension symptom, after drink or heart disease are not allowed to usethis product . Children have a bath must under adult’s guidance. 6.During use please noticed that don’t blocked the jets . Also keepthis product clean and don’t let it blocked by hair or mess. 7.During use, please firstly adjust the water temperature or it will be burned. 8.The outdoor spa is designed with ergonomic, rise and fall changes are dis tiuctly, so pay more attention of slip. 9.Please shut down the system when not use.

Technical Parameter

STEP1

YModel: WS-094D YSize: 2060x1760x790mm YVoltage: 2 2 0 V – 2 4 0 V 5 0 H z YDual- Speed Pump:1.5KW/0.35KW
YHeater:3000W

STEP2

drain pipe

STEP3

01 01

Cleaning and Maintenance
1. The daily maintenance of outdoor spa should be cleaned with ordinary detergent and soft cloth. Please do not use the detergent which contains acetone or ammonia liquid. If there marks or something like glue on the surface of bathtub, just polish it with soft cloth dipping with gas.
2. If there are scratches on bathtub surface, please polish it with 1500# frosted paper dipping with liquid and burnish it with toothpaste. It will be shining again after that.
3. If there are furring on the surface of bathtub, it can be take away by mild acid detergent, for example wipe the bathtub with lemon juice or vinegar which be heated.
4. Do not wipe the chrome plated spare parts all the time, and do not get in touch with chemical detergent etc. Otherwise the surface of chrome plated will be destroyed. The product should be clean by soft cloth other than coarse cloth.
5. To check the water pipe regularly in order to avoid troubles from crack of water pipes or blocked inside.
6. If there are something such as hair stuck inside the jets, then just to twist out the jets and remove it.
7. To clean hydro-massage equipment: To full fill hot water which is 40’C, and pour 2g/L detergent, start hydro-massage function more than 5 minutes, then turn off the massage function and drain out the water. Next, to full fill cold water and start hydro-massage function for 3 minutes, then turn off the massage function and drain out the water, at last, to dry the bathtub with towel.
8. Filter should be clean once a week. 9. Keep out from combustibles and goods which over 80°C to avoid fire
disaster and damage the product. 10.The bathtub should be transported carefully. Do not lay heavy things on it
and do not bump and shaking the tub. If the bathtub has not been used for a long time, drain out the water of the bathtub and keep it in a dry and ventilate environment. Avoid corrosive gas.
06 1006

Troubleshooting

Problems
No power or electricity leaking protection device is activated
Water Jets are not working.

Reasons
1.Electricity leaking protection device cut off power source when electricity line is not well connected. 2.Power or electricity circuit have phenomenon of electricity leaking.
1.check the system whether is on. 2.the impeller of water pump doesn’t rotate 3.water pump is broken which caused by working without water coming in.

Maintenances
1.check and reconnect the wiring system. 2.check the power source, electricity circuit and ground line.
1. turn on the system 2. check through and remove the garbage which is inside the pump. Switch pipe can be removed. 3. install a new water pump

The intensity of hydro-massage cannot be adjusted

1.water pump’s suction has not enough power. 2.air adjustment valve is abnormal 3.jets or nozzles are blocked

1. check the water pump whether is working normally. 2.change the air adjustment valve 3. remove things which are blocking the jets.

Water leaks from the pipes.

1.seal ring is broken 2.screws doesn’t lock tightly 3.pipes doesn’t seal properly. 4.water pipe is broken

1.chang seal ring 2. lock the screws tightly 3. re-seal the silicone. 4. change water pipe

Control panel doesn’t work
No lighting
Radio is off

1.Electricity line didn’t connect to power source, electricity leaking protection device cut off power. 2.power button is not working.
1.The bulb is broken 2. power line is disconnected. 3.control panel is broken
1.speaker is broken 2. power line is disconnected. 3.control panel is broken

1.Re-connect the power source and check the electricity leaking switch button. 2.change a new control panel Lighting is off
1.change a new bulb. 2.re-connect the circuit. 3 .maintain or change control panel
1.change a new speaker 2.reconnect the circuit. 3. maintain or change control panel

Construction Sketch

11

1 1

9

13

11 31 1

12
1 13 1

1

10

1

1

1

6

8

1 31
1

number

name

1

1″Jet

3

3.5″Jet

6

Water suction

8

Lamp

9

Filter

10

Drain

11

Air adjustor

12 Control panel

05 01

02 10

Water controc

When system stay in standard mode, press

dual-speed pump will work as high speed, and all jets spray

water powerfully. Press again, dual-speed will work as low

speed like flter pump, and all jets spray water smoothly.

Heater

Control box

Water pump

Filter Cleaning

0035 0013

*Air adjustor to adjust the intensity of each seat spray (steering counter clockwise Strength increases, clockwise hour intensity decreases)
Note: color is for easy visual recognition.

0024 10