Product Information:
- Product Name: Aqualine Kit 51918 IC Set CS C3 C7 C16 w/ww Auto
Flash Jump Meteor - Battery Type: CR 2025 3V
- Power Supply: Double Insulated, does not require connection to
an Earth circuit - LED Strips: Safety Extra Low Voltage, must not be earthed
- Manufacturer: UK Manufacturer – BH17 7BY, EU Manufacturer –
Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg - Website: www.saxbylighting.com
Product Usage Instructions:
- Commissioning: Place the product in the desired
location. - Operating the Remote Control and Replacing the Battery:
On the left side of the compartment, pull out the battery housing
and replace the exhausted battery with a new CR 2025 3V battery.
Make sure to insert the battery with the correct polarity. - Recycling Advice: Do not dispose of waste electrical
products with household waste. Please recycle where facilities
exist. Check with your Local Authority or retailer for recycling
advice. - Safety Information: Always switch off the power supply
before changing lightbulbs or cleaning for your safety. - Installation: Install the product in accordance with IEE
Wiring regulations and current Building Regulations. If unsure,
consult an electrician. Ensure the cables are kept away from areas
where they may be at risk of being cut, trapped, or damaged. Do not
install in very wet areas. - Basic Installation:
- Plan the layout and ensure the cables will reach the desired
distance between the product and the power supply. - Stick the product to most surfaces using the adhesive backing.
Ensure the surface is clean and dry. - If necessary, use conduit or plastic trunking to hide and
protect the cables. - Do not bend the product sharply or fold it at any point.
- Seal the end of the product with a small amount of silicone
sealant to prevent water ingress. - Connect the cables to the power supply and ensure they are
securely connected. - Avoid cutting or damaging the product during installation or
maintenance. If damage occurs, the affected part should be
scrapped.
- Plan the layout and ensure the cables will reach the desired
- Battery Care: Always remove exhausted batteries from the
remote control. Dispose of batteries properly and in accordance
with local regulations. - Product Suitability: This product is suitable for use by
adults only.
Please refer to the provided specification for additional
details about the product’s electrical requirements and layout.
Commissioning
place.
Operating the remote control and replacing the battery
left of the compartment. Pull the battery housing out and replace the exhausted battery with a new one – make sure
Instruction leaflet
Aqualine Kit
51918
IC Set CS C3 C7 C16
w/ww
Auto
Flas h Jump Meteo r
+ CR 2025
3V
+ CR 2025
3V
+ CR 2025
3V
+ CR 2025
3V
Recycling advice
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice.
Safety information
For your safety, always switch off the power supply before changing lightbulbs, or cleaning.
UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
V5 10/05/2022 Saxby Lighting
satisfactory operation of this product. Please retain these instructions for future reference.
Warning
The power supply is Double Insulated and does not require connection to an Earth circuit. The LED strips are Safety Extra Low Voltage and must not be earthed. Please read these instructions carefully before commencing any work.
electrician. Install in accordance with IEE Wiring regulations and current Building Regulations.
when installing or maintaining this system.
cannot be serviced. If damage occurs the part should be scrapped.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice. Battery care:
Always remove exhausted batteries from the remote control. Always insert the battery with the correct
product is suitable for use by adults only.
Specification
220-240V~ 50Hz
Specification
Layout
which can be stuck to most surfaces. of 100mm or multiples of 100mm. ensuring the cables will reach the distance between
away from areas where they may be at risk from being cut, trapped or damaged.
conduit or plastic trunking.
very wet areas.
Basic Installation
this stage.
ensure that the cable can connect when in the desired position.
anywhere else on the strip as this may cause the Seal the end with a small amount of silicone sealant. correct.
the line on the strip with four copper pads, as shown below.
5000mm


















