RBIV-60 Dual Built-In Refrigerator
Product Information: Dual Built-in Refrigerator
The Dual Built-in Refrigerator from ZLINE Kitchen and Bath is a
luxury appliance that brings elegance and functionality to your
kitchen. The refrigerator features unique designs and unparalleled
quality, providing an elevated experience in the heart of your
home. With an endless selection of features and finishes, this
refrigerator is designed to meet all your needs and
requirements.
This product contains several components, including an adhesive
foam divider, plastic upper bracket, metal lower bracket, divider
trim, and screws. It is important to note that this product
contains nickel, which is a chemical known to the State of
California to cause cancer.
Product Usage: Installation Instructions
Follow the steps below to install the Dual Built-in
Refrigerator:
Tools and Parts:
- Adhesive Foam Divider
- Plastic Upper Bracket
- Metal Lower Bracket
- Screw
- Center Trim
- Phillips head
Attach the Adhesive Foam Divider:
- Approach the refrigerators from behind and angle one of them
out. - Next, measure 2 1/8 from both the top and left corner of the
side of the unit. - Using a level, ensure the divider remains parallel to the edge
of the unit. - Peel the protective sticker off the divider and carefully press
into place.
Mount Brackets:
- On the back of one unit near the top, find the location for one
plastic mounting bracket and screw into place with two screws,
ensuring the small arm is pointed in. - Move to the top of the unit to install the other two plastic
mounting brackets with two screws. - At the back base of the unit, install the metal lower bracket
by unscrewing the two existing screws, sliding into place and
re-screwing both screws. Unscrew the same two screws on the other
unit and set aside for later.
Connect Brackets:
- Realign both refrigerators so they are flush and line up with
the opening where they will be installed. - Finish installing the plastic mounting bracket on the back with
the other two screws to connect both units. Do the same with both
brackets on top. - At the back base of the unit, finish installing the metal lower
bracket by screwing in the two screws set aside earlier. - Install the last metal lower bracket on the front base of both
units using the remaining four screws.
Install Divider Trim:
After ensuring both units are in alignment and everything is
level, insert divider trim between both units and lightly pound
into place with the back of your fist.
For more information, you can scan the QR code provided to watch
an installation video. It is important to note that ZLINE Kitchen
and Bath may change specifications and designs without prior
notice.
Installation Manual
DUAL BUILT-IN REFRIGERATOR
www.zlinekitchen.com
ZLINE Kitchen and Bath provides Attainable Luxury, where the kitchen and bath of your dreams is never out of reach. Through our unique designs and unparalleled quality, we’re dedicated to providing you an elevated experience in the heart of your home. With an endless selection of features and finishes, our inspiration is your reality.
ZLINE is fueled by a passion for innovation; A relentless pursuit of bringing the highest end luxury designs and professional features into everyone’s homes. Because we continually strive to improve our products, we may change specifications and designs without prior notice.
WARNING: This product can expose you to chemicals including nickel, which is known to the State of California to cause cancer. For more information, go to www.P65Warnings.ca.gov.
INSTALLATION
DUAL INSTALLATION COMPONENTS
Divider Trim Plastic Upper Bracket
Adhesive Foam Divider
Metal Lower Bracket
1
Product Specifications
INSTALLATION
TOOLS AND PARTS
Part Adhesive Foam Divider Plastic Upper Bracket Metal Lower Bracket Screw Center Trim
Image
Description
Quantity
1/8″ x 15 3/4″ x 68 7/8″ 1
1/8″ x 2″ x 4 1/2″
3
1/16″ x 1 5/8″ x 2 1/4″
2
Phillips head
20
73 3/4″ long
1
ELECTRICAL AND WATER REQUIREMENTS · Please note that the installation process for your dual built-in refrigerator requires
combining two RBIV-30 model refrigerators to create one RBIV-60 unit. · From an electrical standpoint, each appliance is provided with a NEMA 5-15P
plug and a 3-pin power cable designed to be connected to a 120VAC, 60HZ power receptacle. · Therefore, we recommend both RBIV-30 units be plugged into independent circuits. They can be plugged into the same outlet, but please note the circuit must have a dedicated 15-amp breaker that is not shared with any other appliance to avoid exceeding the combined power requirements. · From a water standpoint, while both RBIV-30 units also come with their own water supply, a qualified technician can easily tee off the water supply to provide water to both units if the customer desires. · Please refer to your RBIV-30 installation manual for additional information for electrical and water requirements and other installation needs.
2
Tools and Parts
INSTALLATION
ATTACH THE ADHESIVE FOAM DIVIDER 1. Approach the refrigerators from behind and angle one of them out. 2. Next, measure 2 1/8″ from both the top and left corner of the side of the unit. 3. Using a level, ensure the divider remains parallel to the edge of the unit. 4. Peel the protective sticker off the divider and carefully press into place.
2 1/8″ 2 1/8″ Adhesive Foam Divider
3
Attach the Adhesive Foam Divider
INSTALLATION
MOUNT UPPER BRACKETS AND LOWER BACK BRACKET TO CONNECT THE REFRIGERATORS 1. On the back of one unit near the top, find the location for one plastic mounting
bracket and screw into place with two screws, ensuring the small arm is pointed in. 2. Move to the top of the unit to install the other two plastic mounting brackets with
two screws. 3. At the back base of the unit, install the metal lower bracket by unscrewing the two
existing screws, sliding into place and re-screwing both screws. Unscrew the same two screws on the other unit and set aside for later.
4
Mount Brackets
INSTALLATION
CONNECT UPPER BRACKETS TO CONNECT THE REFRIGERATORS 1. Realign both refrigerators so they are flush and line up with the opening where
they will be installed. 2. Finish installing the plastic mounting bracket on the back with the other two
screws to connect both units. Do the same with both brackets on top.
CONNECT LOWER BRACKETS TO CONNECT THE REFRIGERATORS 1. At the back base of the unit, finish installing the metal lower bracket by screwing
in the two screws set aside earlier. 2. Install the last metal lower bracket on the front base of both units using the re-
maining four screws.
5
Connect Brackets
INSTALLATION
INSTALL DIVIDER TRIM After ensuring both units are in alignment and everything is level, insert divider trim between both units and lightly pound into place with the back of your fist.
Scan the QR code to watch an installation video.
6
Install Divider Trim
INSTALLATION
PUSH INTO PLACE 1. Before pushing into place, install the necessary power and water connections
(refer to your RBIV-30 installation manual). 2. Uninstall the door on the left unit and reorientate the inside drawers and hinges
so the handle to the door pulls out to the left — opposite of the door on the right unit — then reinstall the door (refer to your RBIV-30 installation manual). 3. Carefully push the dual unit into the cabinet and ensure there is a 1/8″ gap on either side.
Width of cabinet cutout: 59 7/8″ Width of dual unit: 59 5/8″ 1/8″
Scan the QR code to watch an installation video.
WARNING: ZLINE RBIV-30 refrigerators are top-heavy and weigh 342 WARNING pounds. The dual unit weighs close to 700 pounds. Take care when
installing the product; two-person assembly is highly recommended.
7
Push Into Place
INSTALLATION
LEVELING REFRIGERATORS 1. After pushing the dual unit into the cabinet, the feet need to be raised in order to
secure the product to the anti-tip brackets provided with the RBIV-30 installation kit. 2. Raise the front feet first to reduce risk of the product falling frontward. 3. Using a drill and bit shown below, adjust each foot as needed in a clockwise
motion. 4. After adjusting the feet, use a level to ensure the dual unit is level in both width and
depth.
1/4″ bit
Leveling Refrigerators
Front leveling foot
Rear leveling foot
WARNING: The front and rear legs have a maximum height adjustment of WARNING 1 9/16″. Raising the units higher may damage the front and rear leveling
components. If greater height is required, the installer may raise the units on a sheet of plywood or runners.
8
INSTALLATION
INSTALLATION COMPLETE Refer to your RBIV-30 installation manual as needed for other installation procedures.
Need to purchase a part or accessory for your ZLINE product? Visit www.zlineparts.com, ZLINE’s official parts distribution partner.
9
Installation Completion
1.1.1
www.zlinekitchen.com 1-614-777-5004
[email protected]
P65Warnings.ca.gov
ZLINE Kitchen and Bath
ZLINE Kitchen and Bath Parts & Accessories
Range Hood Manuals | ZLINE Kitchen and Bath
