True Fine Td20029fl Celina 3 Light Drum Semiflush Mount Light Instruction Manual

TD20029FL Celina 3 Light Drum SemiFlush Mount Light

Product Information

The 3-Light Flush Mount Lighting (TD20029FL) is a ceiling light
fixture that comes with metal bands, a canopy, a mounting strap,
screws, wire nuts, a shade, an acrylic board, and lamp
instructions. The fixture requires three E26 bulbs that are not
included. The input voltage for the fixture is 120V, and the
maximum rated power is 60W.

Product Usage Instructions

1. Assemble the metal band (B) by screw nut (C) onto the canopy
   (A) and bottom frame (E).
2. Assemble two pieces of metal band (B) first, then put the shade
   (D) on. After that, repeat step 1 to assemble the third and last
   metal band.
3. Adjust the three metal bands (B) and make sure they’re all well
   positioned, then tighten all screw nuts (C).
4. Install bulbs (not included), need three E26 bulbs.
5. Fix mounting strap (I) to outlet box with screw (G).
6. Connect the wires according to the wiring instruction provided.
   Do not connect ground wire to black or white power supply
   wires.
7. Place canopy (A) onto the outlet box, secure with screw
   (H).
8. Peel off the protective cover on acrylic board (G).
9. Gently bend acrylic board (G) a little bit and insert it into
   the bottom of the fixture and then release it. Adjust it to make it
   well positioned.

Wiring Instruction

1. Insert the green grounding screw into the hole with two raised
   dimples on the mounting bar. Wrap the ground wire from the fixture
   (if supplied) around the green grounding screw, then connect it to
   ground wire from the outlet box (if not fixed on the outlet box)
   using a wire connector (not supplied). If ground wire from the
   fixture is not supplied, wrap the ground wire (if not fixed on the
   outlet box) from the outlet box around the green grounding screw
   and tighten it.
2. Identify which group your fixture wire(s) falls into and
   connect the wires according to the directions provided.
3. Take your fixture wire(s) from [Group A] and place evenly
   against the black wire from the outlet box. Do NOT twist wires
   together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector
   clockwise until you feel firmness.
5. Try gently to pull the connector off the wires. If you can pull
   the connector off, carefully re-do steps 3 and 4 as above, and
   check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from
   the outlet box in the same manner. Make sure no bare wires can be
   seen outside wire connectors.

Cleaning

To clean, wipe fixture with a soft cloth. Clean glass with a
mild soap. Do not use abrasive materials such as scouring pads or
powders, steel wool or abrasive paper.

Safety Information

Make sure to follow the wiring instructions provided carefully
to avoid any electrical hazards. Do not connect ground wire to
black or white power supply wires. Do not use abrasive materials to
clean the fixture.

Instructions Manual 3-Light Flush Mount Lighting

Overview

TD20029FL

Outlet box
[GROUP] Black WSmiroeonthuts
Screw(H) Screw(G) Mounting strap(I)

Green(Ground)

White Ribbed

Bare copper wire(Ground) Canopy(A)
Screw nut(C) Shade(D) Metal band (B)

Bulb(F)
(not Included)

Bottom frame(E)

Acrylic board (G)
Assembly Instruction
1. Assemble Metal band(B) by Screw nut(C ) onto Canopy(A) and Bottom frame( E )
2. Assemble 2 pcs of Metal band(B) first, then put the shade on. After that, repeat step 1 to assemble the third and last metal band.
3. Adjust the 3 Metal bands(B) and make sure they’re all well positioned, then tighten all Screw nuts( C )
4. Install Bulbs (not included), need three E26 bulbs. 5. Fix Mounting strap (I) to outlet box with Screw (G). 6. Connect the wires according to the picture above.(Please refer to the
wiring instruction for details ) 7. Place Canopy (A) onto the outlet box, secure with Screw (H). 8. Peel off the protective cover on acrylic board(G) 9. Gently bend acrylic board (G) a little bit and insert it into the bottom
of the fixture and then release it. Adjust it to make it well positioned.

Wiring Instruction
1.Insert the green grounding screw into the hole with two raised dimples on the mounting bar. Wrap the ground wire from the fixture (if supplied) around the green grounding screw, then connect it to ground wire from the outlet box (if not fixed on the outlet box) using a wire connector (not supplied).If ground wire from the fixture is not supplied, wrap the ground wire (if not fixed on the outlet box) from the outlet box around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE POWER SUPPLY WIRES.
2.Take note for the color of the wire(s) on your fixture. Identify which group your fixture wire(s) falls into and connect the wires according to the directions below:

BLACK

WHITE

*PARALLEL WIRE (round & smooth) *PARALLEL WIRE (square & ridged)

WHITE OR GREY WITE TRACER

WHITE OR GREY WITHOUT TRACER

BROWN, GOLD OR BLACK WITHOUT TRACER

BROWN, GOLD OR BLACK WITH TRACER

3.Take your fixture wire(s) from [Group A] and place evenly against the black wire from the outlet box. Do NOT twist wires together before using wire connectors.
4. Fit a wire connector over the wires and screw the connector clockwise until you feel firmness.
5.Try gently to pull the connector off the wires. If you can pull the connector off, carefully re-do steps3 and4 as above, and check again for a firm connection.
6. Connect the fixture wire from [Group B] to the white wire from the outlet box in the same manner. Make sure no bare wires can be seen outside wire connectors.

Product Specifications
Input Voltage 120V Rated Power 60W Max Lamp Socket E26
Product Packaging
Metal band x 3 & Screw nut x 6 Canopy x 1 & Mounting strap x 1 Screw x 2 & wire nut x 3 Shade x 1 Acrylic board x 1 Lamp instruction x 1
Cleaning
To clean,wipe fixture with a soft cloth. Clean glass with a mild soap.Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Safety Information
Always switch off the electricity supply and allow to cool for 10 minutes before changing the light bulbs.
CONTACT US
E-mail:service @24h-reply.com

Print in china

References

• Digital Services, Technology and Consulting | Reply