DS-7600NI-H2/P Series CCTV Cameras

Installation Manual of DS-7600NI-H2/P Series

Overview

The DS-7600NI-H2/P Series is a Network Video Recorder (NVR)
designed for use with IP cameras. It supports up to 32 IP cameras
and provides various features such as live view, recording,
playback, and backup.

Preventive and Cautionary Tips

Before connecting and operating your NVR, please be advised of the
following tips:

• It is not recommended to replace the batteries by the user,
  since improper use or replacement of the battery may result in
  damage to the device.

Chipset Features

The DS-7600NI-H2/P Series uses a high-performance embedded
microprocessor and supports H.265/H.264 video compression.

Interface Description

Front Panel Introduction

The front panel of the DS-7600NI-H2/P Series includes:

• Power Button: Press to start or shut down the device.
• Status LED Indicators Tx/Rx: Blinks in green when there is
  network data transmission.
• HDD USB Ports: Universal Serial Bus (USB) 2.0 ports for
  additional devices such as USB mouse and USB Hard Disk Drive
  (HDD).

Rear Panel Introduction

The rear panel includes:

• LAN: RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet
  interface.
• RS-232: Interface for debugging and maintenance.
• Line in: Audio input for two-way audio function.
• PoE: Network interface for the cameras and to provide power
  over Ethernet.
• USB 3.0: Universal Serial Bus (USB) 3.0 port for additional
  device such as USB mouse and USB Hard Disk Drive (HDD).
• HDMI: Video output interface.
• VGA: Video output interface.
• Audio out: RCA connector for audio output.
• Alarm in/out: Connector for alarm input/output.
• Power supply: Power supply interface.
• Power switch: Power switch.

Motherboard Introduction

The motherboard of the DS-7600NI-H2/P Series includes:

• Debug card interface: For the purpose of debugging and
  maintenance.
• Nonstandard ATX power interface, with 6 pins.
• Debug card interface for BIOS: For the purpose of debugging and
  maintenance the BIOS module.
• Power interface for SATA, with 4 pins.
• 2 SATA interfaces for the system disk and system storage.
• Front panel interface, with 6 pins.
• FAN interface.
• USB 2.0 interface for front panel, with 9 pins.

Product Usage Instructions

1. Connect the NVR to a power source using the power supply
interface and turn on the power switch. 2. Connect IP cameras to
the NVR using the network interfaces. 3. Connect a monitor to the
NVR using either the HDMI or VGA video output interface. 4. Use a
USB mouse to navigate through the NVR’s user interface. 5. Use the
NVR’s features such as live view, recording, playback, and backup
to manage your IP cameras.

Installation Manual of DS-7600NI-H2/P Series
DS-7600NI-H2/P Series
Installation Manual
UD.7L0202D1761B01 1

Installation Manual of DS-7600NI-H2/P Series Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer. Before you start, read the following statement first: This manual, as well as the software described in it, is furnished under license and may be used or copied only in accordance with the terms of such license. The content of this manual is furnished for informational use only, is subject to change without notice. We assume no responsibility or liability for any errors or inaccuracies that may appear in the book. During using the surveillance equipment, please obey the applicable laws and regulatory requirements. Using the equipment for monitoring people’s privacy for other improper purpose is regarded as illegal. The installation manual is applicable to DS-7600NI-H2/4P and DS-7600NI-H2/8P series.
1

Installation Manual of DS-7600NI-H2/P Series
Preventive and Cautionary Tips
Before connecting and operating your NVR, please be advised of the following tips: It is not recommended to replace the batteries by the user, since improper use or replacement of the battery may result in
hazard of explosion. If needed, replace with the same or equivalent type only. Ensure unit is installed in a well-ventilated, dust-free environment. Ensure at least 2cm (0.79 inch) space between two devices. Environmental temperature should be within the range of 0ºC 45ºC (+32 ºF ~ +113ºF). Environmental humidity should be within the range of 10% ~ 90%. The dust on the circuit board inside the device will short circuit the board. Please use the soft brush to clean the circuit board,
the connector, the chassis and the fan. You can also use the water-diluted neutral detergent to wipe away the dust and then dry the components. The volatile solvents, such as alcohol, benzene or thinner, are not allowed to clean the device. Ensure no danger will be caused because of the uneven mechanical load. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter. Unit is designed for indoor use only. Keep all liquids away from the NVR. Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit. Use the NVR in conjunction with an UPS if possible. Power down the unit before connecting and disconnecting accessories and peripherals. A factory recommended HDD should be used for this device. Ensure the NVR is grounded.
2

Installation Manual of DS-7600NI-H2/P Series

Table of Contents

Chapter 1 Chapter 2 Chapter 3
Chapter 4
Chapter 5

Overview …………………………………………………………………………………………………………………………… 3 Chipset Features………………………………………………………………………………………………………………… 4 Interface Description …………………………………………………………………………………………………………. 5 3.1 Front Panel Introduction ………………………………………………………………………………………………. 5 3.2 Rear Panel Introduction ……………………………………………………………………………………………….. 5 3.3 Motherboard Introduction …………………………………………………………………………………………….. 6 Operating System Installation…………………………………………………………………………………………….. 8 4.1 Installing a HDD…………………………………………………………………………………………………………. 8 4.2 Setting Boot Sequence …………………………………………………………………………………………………. 9 4.3 Installing Operating System………………………………………………………………………………………… 10 4.4 Installing Driver………………………………………………………………………………………………………… 10 Specification…………………………………………………………………………………………………………………….. 12

Installation Manual of DS-7600NI-H2/P Series

Chapter 1 Overview
DS-7600NI-H2/P series is an embedded development platform. It is designed for professional digital surveillance. It is featured with well performance in CPU processing, encoding and decoding, and storage capability. Due to the openness of IA structure, various PC application software can be applied to the product, and providing a flexible NVR solution for the software developers or system integrators. Developing Support: Support the Windows 7 (32bit / 64 bit) and Windows 8 (32bit / 64 bit) operating system. Provide the system SDK and open-source DEMO for programmable alarm input/output and PoE (Power over Ethernet)
port. Provide third-party drivers including audio card driver, network interface driver, chipset driver, graphics card driver, etc.

Application

Software Partners

Windows Operating System SDK, Demo and Driver

Third Party Drivers

DS-7600NI-H2/P Hardware

Figure 1. 1 Development Support

3

Installation Manual of DS-7600NI-H2/P Series
Chapter 2 Chipset Features
Intel® Celeron® Processor J1900 (2M Cache, 2.00GHz) with low power consumption and high performance. Flexible development due to IA structure. 1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface. 4/8 PoE (Power over Ethernet) ports. H.264 hardware compression. Programmable alarm input/output and PoE ports. Compact and flexible structure design.
4

Installation Manual of DS-7600NI-H2/P Series
Chapter 3 Interface Description
3.1 Front Panel Introduction

No.

Name

1

Power Button

Power

2

Status LED Indicators Tx/Rx

HDD

3 USB Ports

1

2

3

Figure 3. 1 View of Front Panel

Table 3. 1 Description of Front Panel Description
When the device is off and the power switch in rear panel is on, press the power button to start the device. When the device is on, press the power button to shut down the device. Power indicator is red when the device is running and no light means the device is shutdown. Tx/Rx blinks in green when there is network data transmission.
HDD indicator blinks in green when hard disk writing or reading. Universal Serial Bus (USB) 2.0 ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD).

3.2 Rear Panel Introduction

1

23

4

56 7 8 9

Figure 3. 2 Rear Panel View

10 11

No.

Name

1 LAN

2 RS-232

Table 3. 2 Rear Panel Description Description
1 RJ-45 10 /100 /1000 Mbps self-adaptive Ethernet interface. RS-232 interface for debugging and maintenance.

5

Installation Manual of DS-7600NI-H2/P Series

No.

Name

3 Line in

4 PoE

5 USB 3.0
6 HDMI 7 VGA 8 Audio out 9 Alarm in/out 10 Power supply 11 Power switch

Description Audio input for two-way audio function. Network interface for the cameras and to provide power over Ethernet. 4 PoE interfaces for DS-7600NI-H2/4P and 8 for DS-7600NI-H2/8P. Universal Serial Bus (USB) 3.0 port for additional device such as USB mouse and USB Hard Disk Drive (HDD). HDMI video output interface. VGA video output interface. RCA connector for audio output. Connector for alarm input/output. Power supply interface. Power switch.

3.3 Motherboard Introduction

Figure 3. 3 Motherboard View

Table 3. 3 Motherboard Description

No.

Description

1

Debug card interface. For the purpose of debugging and maintenance.

2

Nonstandard ATX power interface, with 6 pins.

Debug card interface for BIOS. For the purpose of debugging and maintenance the 3
BIOS module.

4

Power interface for SATA, with 4 pins.

5

2 SATA interfaces for the system disk and system storage.

6

Installation Manual of DS-7600NI-H2/P Series

No.

Description

6

Front panel interface, with 6 pins.

7

FAN interface.

8

USB 2.0 interface for front panel, with 9 pins.

9

PoE card interface, with 24 pins.

7

Installation Manual of DS-7600NI-H2/P Series
Chapter 4 Operating System Installation
4.1 Installing a HDD
Before you start: Before installing a hard disk drive (HDD), please make sure the power is disconnected from the NVR. A factory recommended HDD should be used for this installation. Steps:
1. Remove the cover from the NVR by unfastening the screws on the rear and side panel. 2. Connect one end of the data cable to the motherboard of NVR and the other end to the HDD.
Figure 4. 1 Connecting Data Cable 3. Connect the power cable to the HDD.
Figure 4. 2 Connecting Power Cable 4. Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.
8

Installation Manual of DS-7600NI-H2/P Series
Figure 4. 3 Placing the HDD and Fastening the Screws 5. Re-install the cover of the NVR and fasten screws.
4.2 Setting Boot Sequence
Purpose: When installing the operating system, you need to manually set the CD/DVD-ROM Drive as the first boot type. Steps: 1. Enter BIOS interface when starting process by pressing F2 on keyboard. 2. Enter Advance settings interface by pressing direction buttons and Enter button on the keyboard.
Boot > Legacy > Normal Boot Menu > Advance
Figure 4. 4 Boot Configuration Interface 3. Set the CD/DVD-ROM Drive as the first boot type.
9

Installation Manual of DS-7600NI-H2/P Series
Figure 4. 5 Setting the Boot Type
4.3 Installing Operating System
Before you start: If you use a SATA CD/DVD-ROM drive, connect it to the interface of SATA. If you use a USB CD/DVD-ROM drive, connect it to any of the USB interfaces. Step: Insert the Windows installation CD and install the operating system.
4.4 Installing Driver
Purpose: The NVR is attached with a driver installation program when delivery. The program is used for installing system driver, including motherboard chipset driver, audio card driver, graphics driver, etc. And it is applicable to windows 7 and windows 8 of 32 bit and 64 bit. Step: For the detailed steps, please refer to driver installation manual. After successfully installing the drivers, you can view the drivers listed in the Computer Management interface.
10

Installation Manual of DS-7600NI-H2/P Series Graphics Driver
Network Driver Audio Driver Figure 4. 6 Computer Management Interface
11

Installation Manual of DS-7600NI-H2/P Series

Chapter 5 Specification

Model Processor Memory Network Video/Audio output
HDD interface
External interface
Other

DS-7600N-H2/4P

DS-7600N-H2/8P

Type

Intel® Celeron® Processor J1900 (2M Cache, 2.00GHz)

Memory size

4GB

Incoming bandwidth

300Mb

HDMI output

1-ch, resolution: 1920 × 1080/60Hz

VGA output

1-ch, resolution: 2560 × 1600/30Hz

Audio output

1 RCA (2.0Vp-p, 1k)

SATA interface

2

Capacity

Up to 4TB for each HDD.

HDD type

Support enterprise-class, surveillance-class and desktop HDD.

Network interface

1 1000Mbps self-adaptive Ethernet interface.

PoE interface

4-ch

8-ch

Two-way audio interface 1 RCA (2.0Vp-p, 1k)

Serial port USB interface Alarm in/out

1 × RS-232 2 USB 2.0 interfaces in front panel and 1 USB 3.0 interface in rear panel. 16 / 4

Power supply

100 ~ 240VAC

Working temperature

0ºC ~ 45ºC (+32 ºF ~ +113ºF)

Working humidity

10% ~ 90%

Chassis

1U chassis

Dimensions (W×D×H) 445 × 290 × 45mm(17.5″ × 11.4″ × 1.8″)

Weight (without HDDs) 4 Kg (8.8lb)

12