In Common With Gemma Sconce Wall Light Instruction Manual

Gemma Sconce Wall Light

Product Information

The Gemma Sconce is a stylish and modern light fixture that adds
a touch of elegance to any space. It comes with a Mudring, which is
a mounting accessory that helps secure the fixture to the wall or
ceiling. The sconce includes various components such as a
backplate, mud ring, mounting screws, Wago clips, base screw,
mounting bracket, G9 LED bulb, diffuser, and Gemma shade.

Product Usage Instructions

1. Before starting the installation, make sure to turn off the
   electrical power at the main fuse box or circuit panel.
2. Using a Phillips head screwdriver, mount the backplate (Part A)
   to the junction box by tightening the mounting screws (Part D).
   Ensure that the wires from the junction box remain accessible.
3. Attach the mudring (Part B) to the backplate (Part A) using the
   two flat head mounting screws (Part E).
4. Apply drywall mesh tape (Part C) by overlapping it on the
   perimeter of the mud ring and the wall. Plaster over the drywall
   mesh-tape, mudring, and wall. It is recommended to apply three
   coats of plaster, allowing each coat to dry and sanding between
   coats. Ensure this area is painted before proceeding.
5. Attach the mounting bracket (Part H) to the exposed part of the
   mudring (Part B) using additional mounting screws (Part D).
6. Use the Wago clips (Part F) to connect the fixture’s wires to
   the corresponding wires from the junction box. Remember that white
   is neutral, black is live, and green/yellow is ground. Use a wire
   stripper if needed to remove 3/8 of the insulation from each wire
   before inserting them into the corresponding Wago clip (Part
   F).
7. Slide the L base (Part I) over the mounting bracket (Part
   C).
8. Secure the L base using the provided base screw (Part G).
9. Carefully slide the Gemma shade (Part M) over the socket.
10. Secure the shade (Part M) into place using the washer and
    provided tool (Part H).
11. Push the included G9 LED bulb into socket (Part K).
12. Thread the diffuser (Part L) over the bulb.
13. Turn the power back on at the main fuse box or circuit panel
    that was disabled before installation.

Gemma Sconce, Mudring
How to Install Your New Light Please check that you received all of the components pictured in this guide. Reach out to us if anything is missing. It’s very rare, but it happens. Don’t forget to turn off the electrical power source.
Tools you will need that aren’t included: standard wire stripper, Phillips head screwdriver.
CAUTION Electrical shock risk. Turn off electrical power at the main fuse box or circuit panel before beginning installation, servicing the light, or installing accessories. We recommend working with a qualified electrician familiar with the type of work you’d like done.
ATTENTION Risque de choc électrique. Coupez l’alimentation électrique au niveau de la boîte à fusibles principale ou du panneau de circuits avant de commencer l’installation, l’entretien de la lumière ou l’installation d’accessoires. Nous vous recommandons de travailler avec un électricien qualifié familier avec le type de travail que vous souhaitez effectuer.

Contents

Part A Backplate

Part B Mud Ring

Part C Mesh Tape

Part D Mounting Screws (x4)

Part E Mounting Screws (x2)
(flat head)

Part F Wago Clips (x3)

Part G

Part H

Part I

Base Screw (x2) Mounting Bracket L Base

Part J

Part K

Tool + Washer G9 LED Bulb

Part L Diffuser

Part M Gemma Shade

Assembly Guide

1 of 4

incommonwith.com

Gemma Sconce, Mudring

Step 1: Turn off electrical power at the main fuse box or circuit panel before beginning installation.

Step 2: Mount the backplate (A) to the junction box using a phillips head screwdriver to tighten the mounting screws (D). Make sure that the wires from the junction box are still accessible.

D A

!

Step 3: Attach the mudring (B) to the backplate (A) using the two flat head mounting screws (E).

Step 4: Apply drywall mesh tape (C), overlapping the perimeter of the mud ring and the wall. Plaster over drywall mesh-tape, mudring, and wall. We recommend applying three coats of plaster, allowing time for the plaster to dry and sanding between coats. Ensure this area painted before proceeding to the next steps.

C A

B

E

Assembly Guide

2 of 4

incommonwith.com

Gemma Sconce, Mudring

Step 5: Attach the mounting bracket (H) to the exposed part of the mudring (B) using the additional mounting screws (D).
B
D

Step 6: Use the wago clips to connect the fixture’s wires to the corresponding wires from the junction box in the wall or ceiling. White is neutral; Black is live; Green/ Yellow is ground. One ground wire will be attached to the backplate, the other ground wire should come from the junction box. If needed use a wire stripper to remove 3/8″ of the insulation from each wire before inserting them into the corresponding wago clip (F).
I
F H

H

Step 7: Slide L base (D) over the mounting bracket (C). I

Step 8: Secure using the provided base screw (G).

G H

Assembly Guide

3 of 4

incommonwith.com

Gemma Sconce, Mudring

Step 9: Carefully slide the Gemma shade (M) over the socket.

Step 10: Secure the shade (M) into place using the washer and provided tool (H).
J

M

Step 11: Push the included bulb into socket (K). K

M
Step 12: Thread the diffuser (L) over the bulb. Turn the power back on at the main fuse box or circuit panel you disabled before installation.
L

Assembly Guide

4 of 4

incommonwith.com

References

• In Common With